AI Article Synopsis

  • Hygroscopic compounds like LiCl, CaCl2, and MgCl2 enhance the performance of heat and moisture exchangers (HME) by improving water retention, but can also lead to systemic absorption through the bronchopulmonary tract.
  • Lithium, particularly in forms like LiCl, poses risks of side effects including nausea and cardiac issues, complicating differentiation from similar symptoms experienced during anesthesia.
  • Research showed significant variability in LiCl content in HMEs, with notable lithium plasma concentration increases in some patients, highlighting potential risks, especially in vulnerable populations like infants.

Article Abstract

Such hygroscopic compounds as LiCl, CaCl2, and MgCl2 are used to improve water retention capacity and, as a consequence, the effectiveness of heat and moisture exchangers (HME). Resorption of these substances via the bronchopulmonary tract and a resulting systemic action cannot be excluded, especially if additional active moisturizing devices are used. The narrow therapeutic range of lithium is known, as are its unwanted side effects, such as nausea, vomiting, somnolence and even cardiac arrhythmia. These are symptoms that also frequently occur during anaesthesia and intensive care, so that differentiation against effects of lithium is nearly impossible. We investigated whether, in theory and in practice, LiCl-coated HME could result in effective Li plasma concentrations. We measured (1) total LiCl content of HMEs, (2) release of this content, simulating the worst-case situation with a breathing model, and (3) lithium plasma concentrations of adult patients being ventilated during anaesthesia with a rebreathing circuit and LiCl-coated HME, but with no additional active moisturizing system incorporated. RESULTS. The results show striking differences with LiCl content ranging from 3 to 251 mg varying not only between different types of HME but also within the same lots. After 20 min of ventilation more than 90% of the LiCl coating was rinsed into the test lung of the breathing model. In practical use, we observed an increase in lithium plasma concentration in 3 of 20 investigated patients. The plasma values of maximum 49.5 micrograms/l (= 0.007 mmol/l) do not amount to potentially toxic concentrations. Nevertheless, clinically relevant concentrations might occur in patients with small distribution volumes, e.g. newborns or infants with frequent exposition within short intervals such as in intensive care units. The differences in lithium content also indicate qualitative differences in water retention capacity. Because of the potential side effects of lithium, we prefer qualitatively equivalent HMEs, e.g., with MgCl2 or CaCl2 as hygroscopic substance.

Download full-text PDF

Source

Publication Analysis

Top Keywords

heat moisture
8
water retention
8
retention capacity
8
additional active
8
active moisturizing
8
side effects
8
intensive care
8
effects lithium
8
licl-coated hme
8
plasma concentrations
8

Similar Publications

Mechanical properties of a polylactic 3D-printed interim crown after thermocycling.

PLoS One

January 2025

Department of Advanced General Dentistry, College of Dentistry, Yonsei University, Seoul, Korea.

Polylactic acid (PLA) has garnered attention for use in interim dental restorations due to its biocompatibility, biodegradability, low cost, ease of fabrication, and moderate strength. However, its performance under intraoral conditions, particularly under heat and moisture, remains underexplored. This study evaluated the mechanical properties of PLA interim crowns compared with those of polymethylmethacrylate (PMMA) and bisphenol crowns under simulated intraoral conditions with thermocycling.

View Article and Find Full Text PDF

Hydrogen production by suspension self-rotation enhanced pyrolysis of sludge particles in cyclone.

Water Res

January 2025

National Engineering Research Center of Industrial Wastewater Detoxication and Resource Recovery, East China University of Science and Technology, Shanghai, 200237, China. Electronic address:

The challenges faced by sludge pyrolysis units, including poor heat transfer efficiency and uneven heating of material groups, significantly hinder the green and low-carbon transformation and sustainable development of sludge treatment. The suspension self-rotation of sludge particles in a cyclone enhances particle heat transfer, thereby improving the pyrolysis process. In this study, we developed a novel method for sludge pyrolysis using Cyclone Suspension Self-Rotation Pyrolysis Reactor (CSSPR).

View Article and Find Full Text PDF

Type 1 resistant starch (RS1) was prepared by high-pressure homogenization of corn starch (CS) embedded with 0.1 %, 0.3 %, 0.

View Article and Find Full Text PDF

Synthesis and characteristics of type 3 resistant waxy corn starch by removal of starch granule surface proteins and heat-moisture treatment.

Food Chem

January 2025

Engineering Research Center of Bio-process, Ministry of Education, Hefei University of Technology, 193 Tunxi Road, Hefei, Anhui 230009, PR China; School of Food Science and Engineering, Hefei University of Technology, Hefei, Anhui 230009, PR China.

The type 3 resistant waxy corn starch (RS3) was synthesized by removing starch granule surface proteins and subjecting it to heat-moisture treatment at -20°C, 4°C, and 25°C. Upon applying the dual modification, a significant reduction in particle size and in vitro digestion was observed, while the gelatinization enthalpy, relative crystallinity, and resistant starch content increased. Notably, RS3 treated at 4°C demonstrated the lowest digestion rate of 3.

View Article and Find Full Text PDF

Development of heat sealable film from tapioca and potato starch for application in edible packaging.

J Food Sci Technol

February 2025

Department of Food Technology and Nutrition, Faculty of Technology, Mahasarakham University, Maha Sarakham, 44150 Thailand.

This study aimed to fabricate edible films from tapioca (T) and potato (P) starch, assessing their physicochemical properties and biodegradation across different ratios (T100P0, T70P30, T50P50, and T30P70). The films underwent evaluation for moisture content, thickness, water vapor permeability, and color values. T100P0 and T30P70 formulations exhibited the highest film transparency at 43.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!