Food provocation test (FPT) is one of important diagnostic methods for food allergy, but no standard antigens for FPT have yet been developed. In this study, dried powders were manufactured from five kinds of foods (cow's milk, hen egg, chicken, soybean and wheat) by spray-drying or freeze-drying and examined in vitro for their usefulness as antigens for FPT. In SDS-PAGE, the migration pattern of the extract from each powder was the same as or closely similar to that of the extract from its material. When analyzed by ELISA, a good correlation (r=0.853-0.978) in the reactivity with sera from food-allergic patients was observed between the extracts from each powder and its material. Moreover, in cow's milk, hen egg and soybean, almost the same ELISA inhibition curves were drawn, regardless of whether the extracts from each powder and its material were used as immobilized antigens or inhibitors. These results demonstrated that each powder contains the same allergens as its material at almost the same levels, being useful as an antigen for FPT. Favorably, the powders were found to be stored without significant changes in IgE reactivity at -20 degrees C or 5 degrees C for more than 18 months, although their storage at room temperature was suggested to be avoided.

Download full-text PDF

Source

Publication Analysis

Top Keywords

powders manufactured
8
food provocation
8
antigens fpt
8
cow's milk
8
milk hen
8
hen egg
8
extracts powder
8
powder material
8
[in vitro
4
vitro evaluation
4

Similar Publications

This study investigates the optimization of mechanical milling parameters to enhance the recycling of Ti6Al4V machining chips, addressing a significant challenge in sustainable materials processing. The influence of ball-to-powder ratio (BPR) and ball size distribution on powder characteristics, including crystallite size, particle size, and phase composition, was systematically examined. Key findings include a 30% reduction in crystallite size, with the smallest crystallite size of 51.

View Article and Find Full Text PDF

Fabrication of Piezoelectric Structures with High Porosity by Digital Light Processing.

3D Print Addit Manuf

October 2024

School of Mechanical Engineering (Shandong Institute of Mechanical Design and Research), Qilu University of Technology (Shandong Academy of Sciences), Jinan, China.

Digital light processing is a recently developed solution to fabricate complex structured piezoelectric devices. To obtain a high-performance device, the slurry configuration, model slicing, and heat treatment methods during the printing should be carefully determined. In this article, 200 nm particle size barium titanate powders with an optimized solid content of 80% (mass fraction) were used to configure the slurry with higher printing efficiency.

View Article and Find Full Text PDF

This article presents a fabrication strategy on the structural design, optimization, additive manufacturing, and processing of metal mirror. Specifically, the study showcases the topology design of a metal mirror with diameter of 200 mm, the additive manufacturing of standard aluminum-based powder (AlSi10Mg), the high-precision single-point diamond turning process of the surface. By setting the feasible domain partition, a topology optimization model suitable for metal additive manufacturing and subsequent surface shaping was constructed, which takes into account the multi-load machining load conditions of single-point diamond turning technology and the material topology representation of standard support structures for additive manufacturing.

View Article and Find Full Text PDF

Application of additive manufacturing TaBw01 porous tantalum rod in ARCO stage II osteonecrosis of the femoral head.

J Orthop Surg Res

December 2024

Center for Joint Surgery, Southwest Hospital, Army Medical University, Gaotanyan Street, Shapingba District, Chongqing, 400038, China.

Purpose: This study aims to investigate the suitable surgical strategies for applying TaBw01 porous tantalum rod across different stages of osteonecrosis of the femoral head (ONFH).

Methods: TaBw01 tantalum rods were fabricated using type FTaY-1 tantalum powder via the foam impregnation-sintering method. Mechanical testing with the Instron 8801 universal testing machine and finite element analysis (FEA) assessed single tantalum rod implantation and impaction bone grafting combined with rod implantation.

View Article and Find Full Text PDF

Graphene aerogels (GAs) with engineered architectures are a promising material for applications ranging from filtration to energy storage/conversion. However, current preparation approaches involve the combination of multiple intrinsically-different methodologies to achieve graphene-synthesis and architecture-engineering, complicating the entire procedure. Here, a novel approach to prepare GAs with engineered architectures based on the laser-upcycling of protein biowaste, hemoglobin, is introduced.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!