Effects of basal debris on glacier flow.

Science

Department of Geological and Atmospheric Sciences, Iowa State University, Ames, IA 50011, USA.

Published: July 2003

Glacier movement is resisted partially by debris, either within glaciers or under glaciers in water-saturated layers. In experiments beneath a thick, sliding glacier, ice containing 2 to 11% debris exerted shear traction of 60 to 200 kilopascals on a smooth rock bed, comparable to the total shear traction beneath glaciers and contrary to the usual assumption that debris-bed friction is negligible. Imposed pore-water pressure that was 60 to 100% of the normal stress in a subglacial debris layer reduced shear traction on the debris sufficiently to halt its deformation and cause slip of ice over the debris. Slip resistance was thus less than debris shearing resistance.

Download full-text PDF

Source
http://dx.doi.org/10.1126/science.1083086DOI Listing

Publication Analysis

Top Keywords

shear traction
12
debris
7
effects basal
4
basal debris
4
debris glacier
4
glacier flow
4
flow glacier
4
glacier movement
4
movement resisted
4
resisted partially
4

Similar Publications

Low-dimensional -based carbon nanostructures, known for their remarkable transport properties and mechanical behaviors, are widely used as reinforcing phases in polymer composites to enhance their performance. While carbon nanocomposites are promising materials for extreme conditions, the damage mechanisms due to charge injection at the interfaces between carbon nanostructures and polymers remain unclear. Using first-principles calculations, we investigated ambipolar charging and structural responses at the interfaces between industrially relevant polymers and carbon nanotubes or graphene upon electron and hole injection.

View Article and Find Full Text PDF

[Microsurgical vascular suture].

Oper Orthop Traumatol

December 2024

Plastisch- und Handchirurgische Klinik, Universitätsklinik Erlangen, Krankenhausstr. 12, 91054, Erlangen, Deutschland.

Objective: Anastomosis of two vessels by end-to-end or end-to-side suturing to create an uninterrupted blood flow between the two vessels.

Indications: Transplantations; replantations; vascular trauma.

Contraindications: Active infections in the area to be vascularized or surgical site; large differences in caliber between the vessels; hypercoagulability; extensive tissue damage.

View Article and Find Full Text PDF

Sandwich panels are widely used in the naval and aerospace industries to withstand the normal tensile, compressive, and shear stresses associated with bending. The faces of sandwich composites are usually made of metals such as aluminum and, in some studies with composites, using a polymeric matrix, but there are no studies in the literature using a castor oil polyurethane matrix. The core of the panel must keep the faces apart and be rigid perpendicular to them.

View Article and Find Full Text PDF

Analysis of aging effects on the mechanical and vibration properties of quasi-isotropic basalt fiber-reinforced polymer composites.

Sci Rep

November 2024

Department of Computer Science and Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education (MAHE), Manipal, 576 104, Karnataka, India.

Eco-friendly natural fiber composites, such as basalt fiber composites, are gaining traction in material science but remain vulnerable to environmental degradation. This study investigates the mechanical and vibrational properties of quasi-isotropic basalt fiber composites subjected to aging in two different environments: ambient (30 ºC) and subzero (-10 ºC), both in distilled water until moisture saturation. Aged specimens absorbed 8.

View Article and Find Full Text PDF

Mechanical testing of colloidal solids with millipascal stress and single-particle strain resolution.

Phys Rev E

August 2024

John A. Paulson School of Engineering and Applied Sciences, Harvard University, Cambridge, Massachusetts 02138, USA.

We introduce a technique, traction rheoscopy, to carry out mechanical testing of colloidal solids. A confocal microscope is used to directly measure stress and strain during externally applied deformation. The stress is measured, with single-mPa resolution, by determining the strain in a compliant polymer gel in mechanical contact with the colloidal solid.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!