The factors affecting the operating life of the light-emitting electrochemical cells (LECs) based on films of tris(2,2'-bipyridine)ruthenium(II) both in sandwich (using an ITO anode and a Ga:Sn cathode) and planar (using interdigitated electrode arrays (IDAs)) configurations were investigated. Stability of these devices is greatly improved when they are produced and operated under drybox conditions. The proposed mechanism of the LEC degradation involves formation of a quencher in a small fraction of tris(2,2'-bipyridine)ruthenium(II) film adjacent to the cathode, where light generation occurs, as follows from the observed electroluminescence profile in the LECs constructed on IDAs, showing that the charge injection in such devices is highly asymmetric, favoring hole injection. Bis(2,2'-bipyridine)diaquoruthenium(II) is presumed to be the quencher responsible for the device degradation. A microscopic study of photo- and electroluminescence profiles of planar light-emitting electrochemical cells was shown as a useful approach for studies of charge carrier injection into organic films.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/ja029550i | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
White light-emitting electrochemical cells based on metal-free TADF emitters.
Nat Commun
January 2025
The Organic Photonics and Electronics Group, Department of Physics, Umeå University, Umeå, Sweden.
The attainment of white emission from a light-emitting electrochemical cell (LEC) is important, since it enables illumination and facile color conversion from devices that can be cost-efficient and sustainable. However, a drawback with current white LECs is that they either employ non-sustainable metals as an emitter constituent or are intrinsically efficiency limited by that the emitter only converts singlet excitons to photons. Organic compounds that emit by thermally activated delayed fluorescence (TADF) can address these issues since they can harvest all excitons for light emission while being metal free.
View Article and Find Full Text PDFP2-NaMnNiCoO stabilized by optimal active facets for sodium-ion batteries.
J Colloid Interface Sci
January 2025
MOE Key Laboratory for UV Light-Emitting Materials and Technology, Department of Physics, Northeast Normal University, Changchun, Jilin 130024, PR China; Faculty of Chemistry, Northeast Normal University, Changchun, Jilin 130024, PR China. Electronic address:
Considering factors such as crustal reserves, atomic mass, redox potential and energy density, sodium-ion batteries (SIBs) are regarded as the most promising alternative to lithium-ion batteries (LIBs). Transition metal-based layered oxides, especially typical NaMnO, stand out among cathode materials due to their low cost and high energy density. However, NaMnO cathodes face several challenges, including Jahn-Teller distortion, manganese dissolution, structural collapse, irreversible phase transition and significant capacity loss.
View Article and Find Full Text PDFImpact of the Electrode Material on the Performance of Light-Emitting Electrochemical Cells.
ACS Appl Mater Interfaces
January 2025
The Organic Photonics and Electronics Group, Department of Physics, Umeå University, SE-90187 Umeå, Sweden.
Light-emitting electrochemical cells (LECs) are promising candidates for fully solution-processed lighting applications because they can comprise a single active-material layer and air-stable electrodes. While their performance is often claimed to be independent of the electrode material selection due to the in situ formation of electric double layers (EDLs), we demonstrate conceptually and experimentally that this understanding needs to be modified. Specifically, the exciton generation zone is observed to be affected by the electrode work function.
View Article and Find Full Text PDFNickel-Cobalt Layered Double Hydroxide Nanosheet-Decorated 3D Interconnected Porous Ni/SiC Skeleton for Supercapacitor.
Molecules
November 2024
Department of Chemical Engineering, National Chung Hsing University, Taichung 40227, Taiwan.
In this study, a three-dimensional (3D) interconnected porous Ni/SiC skeleton (3D Ni/SiC) was synthesized by binder-free hydrogen bubble template-assisted electrodeposition in an electrolyte containing Ni ions and SiC nanopowders. This 3D Ni/SiC skeleton served as a substrate for directly synthesizing nickel-cobalt layered double hydroxide (LDH) nanosheets via electrodeposition, allowing the formation of a nickel-cobalt LDH nanosheet-decorated 3D Ni/SiC skeleton (NiCo@3D Ni/SiC). The multiscale hierarchical structure of NiCo@3D Ni/SiC was attributed to the synergistic interaction between the pseudocapacitor (3D Ni skeleton and Ni-Co LDH) and electrochemical double-layer capacitor (SiC nanopowders).
View Article and Find Full Text PDFBreakage of the dense structure of coal precursors increases the plateau capacity of hard carbon for sodium storage.
Chem Sci
December 2024
MOE Key Laboratory for UV Light-Emitting Materials and Technology, Northeast Normal University Changchun Jilin 130024 China
Article Synopsis
- Hard carbon is a promising material for sodium ion batteries due to its ability to store sodium efficiently, but its production costs are high, prompting efforts to optimize usage of coal-derived hard carbon.
- To enhance the electrochemical performance, a method involving Zn(OH)CO assisted ball milling and subsequent carbonization is proposed to create closed pores within the coal-derived hard carbon, which is essential for increasing capacity.
- The resulting coal-derived hard carbon shows a significant capacity of 325.3 mA h g with a good retention rate over 500 cycles, demonstrating that innovative pore design can significantly boost sodium storage capabilities and utilize coal more effectively.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!