Is one head and neck immobilization system as good as another? One center's experience.

Med Dosim

William Buckland Radiotherapy Centre, The Alfred Hospital, Melbourne, Victoria, Australia.

Published: August 2003

The William Buckland Radiotherapy Center has used 2 different immobilization systems for patients requiring radiotherapy to the head-and-neck region. A polycarbonate mask was manufactured for radical treatments and a thermoplastic mask for palliative treatments. This study evaluated field placement accuracy, staff opinion, and production costs of both systems. The manual matching program of Varian PortalVision Electronic Portal Imaging (EPI) System was used to assess field placement accuracy on a daily basis. Radiation therapists (RTs) were surveyed before and after the study to determine their opinions of each system. Production time and required materials were recorded to assess cost. Nineteen patients from each system had daily EPI results compiled with no statistically significant difference observed in field placement accuracy. The thermoplastic system was found to be more cost efficient due to a combination of the reduced production time and reuseability of the masks. User acceptability of the thermoplastic system has increased so that it is now the preferred system. In conclusion, the thermoplastic system is a viable alternative to the polycarbonate system in terms of treatment accuracy and cost. It is recommended that the thermoplastic system be used for all radical and palliative treatments. In addition, RTs prefer the thermoplastic system.

Download full-text PDF

Source
http://dx.doi.org/10.1016/S0958-3947(02)00240-6DOI Listing

Publication Analysis

Top Keywords

thermoplastic system
20
field placement
12
placement accuracy
12
system
11
palliative treatments
8
production time
8
thermoplastic
6
head neck
4
neck immobilization
4
immobilization system
4

Similar Publications

Acting as the interface between the human body and its environment, clothing is indispensable in human thermoregulation and even survival under extreme environmental conditions. Development of clothing textiles with prolonged passive temperature-adaptive thermoregulation without external energy consumption is much needed for protection from thermal stress and energy saving, but very challenging. Here, a temperature-adaptive thermoregulation filament (TATF) consisting of thermoresponsive vacuum cavities formed by the temperature-responsive volume change of the material confined in the cellular cores of the filament is proposed.

View Article and Find Full Text PDF

Synthesis and characterization of dextran palmitate for extrusion 3D printing.

Int J Biol Macromol

January 2025

KU Leuven, Department of Chemical Engineering, Chemical and Biochemical Reactor Engineering and Safety (CREaS), Celestijnenlaan 200F, 3001 Leuven, Belgium. Electronic address:

The fabrication of objects with complex shape and geometry has been greatly facilitated with the advancements in additive manufacturing. While synthetic polymers like ABS and PLA have found widespread use in extrusion 3D printing, other biobased thermoplastics that are both biodegradable and biocompatible could offer strategic advantages over traditional synthetic materials. In this work dextran of low (20 kDa) and medium (40 kDa) molecular weight (MW) was modified with palmitic acid to obtain meltable polymers for extrusion 3D printing/fused deposition modeling additive manufacturing.

View Article and Find Full Text PDF

Enhanced density separation efficiency of microplastics in presence of nonionic surfactants.

Environ Res

December 2024

College of Environmental Science and Engineering, Qingdao University, Qingdao, China. Electronic address:

Microplastics (MPs) recycling, a promising approach to tackle its pollution, faces significant challenges due to the lack of effective separation methods. Herein, the optimized density separation accompanied with nonionic surfactants was employed to purify single MPs species from mixed systems. By adjusting the flotation fluid density, the single MPs can be separated from their mixtures in equal proportions (e.

View Article and Find Full Text PDF

For wider adoption of the material extrusion (MatEx)-based additive manufacturing (AM) process, it is important to understand the systems for an improved production rate of the machine. This AM process is the most adaptable and popular due to its wide availability, scalability, compatibility with a broad range of thermoplastic materials, and decreasing cost of personal MatEx-based systems. The performance limits are being explored by many researchers, but none have tried to find the efficacy of different kinematic configurations.

View Article and Find Full Text PDF

Observation and Control of Single-Component Adhesion Interphase of Polyamide 66 through Confocal Raman Microspectroscopy.

ACS Appl Mater Interfaces

December 2024

Department of Chemical Science and Engineering, Graduate School of Engineering, Kobe University, Rokko, Nada Kobe 657-8501, Japan.

Manufacturing using adhesion technology has attracted much attention. Examples of adhesion include the lay-up of carbon fiber reinforced thermoplastic prepregs and the lamination of food packaging. In single-component adhesion systems, the analysis of the boundary region poses challenges because of the absence of chemical and physical discrimination at the adhesion interphase.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!