We have developed a new depth-graded multilayer system comprising W and SiC layers, suitable for use as hard x-ray reflective coatings operating in the energy range 100-200 keV. Grazing-incidence x-ray reflectance at E = 8 keV was used to characterize the interface widths, as well as the temporal and thermal stability in both periodic and depth-graded W/SiC structures, whereas synchrotron radiation was used to measure the hard x-ray reflectance of a depth-graded multilayer designed specifically for use in the range E approximately 150-170 keV. We have modeled the hard x-ray reflectance using newly derived optical constants, which we determined from reflectance versus incidence angle measurements also made using synchrotron radiation, in the range E = 120-180 keV. We describe our experimental investigation in detail compare the new W/SiC multilayers with both W/Si and W/B4C films that have been studied previously, and discuss the significance of these results with regard to the eventual development of a hard x-ray nuclear line telescope.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/ao.42.002415 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
An Enhanced Bioactive Glass Composition with Improved Thermal Stability and Sinterability.
Materials (Basel)
December 2024
Department of Engineering "Enzo Ferrari", University of Modena and Reggio Emilia, Via P. Vivarelli 10, 41125 Modena, Italy.
The development of new bioactive glasses (BGs) with enhanced bioactivity and improved resistance to crystallization is crucial for overcoming the main challenges faced by commercial BGs. Most shaping processes require thermal treatments, which can induce partial crystallization, negatively impacting the biological and mechanical properties of the final product. In this study, we present a novel bioactive glass composition, S53P4_MSK, produced by a melt-quench route.
View Article and Find Full Text PDFStudy on the Effect of Laser Power on the Microstructure and Properties of Cladding Stellite 12 Coatings on H13 Steel.
Materials (Basel)
December 2024
College of Mechanical and Automotive Engineering, Ningbo University of Technology, Ningbo 315221, China.
To address the issue of cracking in aluminum extrusion dies during operation, this study employs laser cladding technology to modify the surface of these dies. This modification aims to enhance their hardness and friction resistance. Laser cladding technology was utilized to coat the surface of H13 steel with Stellite 12, a cobalt-based alloy, at varying laser power levels.
View Article and Find Full Text PDFAnalysis of printing temperature effect on texture modification: Potential of soy protein isolate-based bigel for swallowing-friendly food.
Int J Biol Macromol
January 2025
Institute of Food Science and Technology, Chinese Academy of Agricultural Sciences, Key Laboratory of Agro-products Processing, Ministry of Agriculture and Rural Affairs, Beijing 100193, China; Institute of Western Agriculture, Chinese Academy of Agricultural Sciences, Changji 831100, China. Electronic address:
This work prepared the soy protein isolate (SPI)-beeswax-based bigel loaded with β-carotene, and the effect of printing temperature (PT) on texture regulation was investigated. During printing, increasing PT weakened the rheological properties and printability of ink. However, the mechanical strength and deformation resistance at non-linear regions of products were strengthened after printing.
View Article and Find Full Text PDFEffect of post-processing on the surface, optical, mechanical, and dimensional properties of 3D-printed orthodontic clear retainers.
Clin Oral Investig
January 2025
School of Materials Science and Innovation, Faculty of Science, Mahidol University, Phuttamonthon 4 Road, Salaya, Phuttamonthon District, Nakhon Pathom, 73170, Thailand.
Objectives: To address the high surface roughness and poor optical properties of three-dimensional (3D) printed orthodontic clear retainers, an alternative post-processing protocol was investigated with the goal of achieving improved surface, optical, and mechanical properties while preserving dimensional accuracy.
Materials And Methods: Samples were prepared from two biocompatible methacrylate-based 3D-printing resins (Formlabs Dental LT Clear V2, NextDent OrthoFlex) and one thermoplastic material (Duran). For the 3D-printed resins, one group was post-processed by rinsing in isopropyl alcohol, while another group was centrifuged before post-curing in glycerine.
Augmented Reality for Surgical Navigation: A Review of Advanced Needle Guidance Systems for Percutaneous Tumor Ablation.
Radiol Imaging Cancer
January 2025
From the Department of Clinical Affairs, MediView XR, Cleveland, Ohio (M.E.); College of Medicine, Alfaisal University, Riyadh, Saudi Arabia (A.B.); and Department of Diagnostic Radiology, Section of Interventional Radiology, Cleveland Clinic Foundation, 9500 Euclid Ave, Cleveland, OH 44195-5243 (S.K., K.G., C.M.).
Percutaneous tumor ablation has become a widely accepted and used treatment option for both soft and hard tissue malignancies. The current standard-of-care techniques for performing these minimally invasive procedures require providers to navigate a needle to their intended target using two-dimensional (2D) US or CT to obtain complete local response. These traditional image-guidance systems require operators to mentally transpose what is visualized on a 2D screen into the inherent three-dimensional (3D) context of human anatomy.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!