Surface modification of an experimental silicone rubber maxillofacial material to improve wettability.

J Dent

Department of Basic Dental Science, College of Medicine, University of Wales, Heath Park, Cardiff CF14 4XY, UK.

Published: March 2003

Objectives: Good wettability of maxillofacial prosthetic materials is important so that a lubricating layer is formed with supporting tissues thus reducing patient discomfort. The purpose of the study was to surface modify an experimental silicone rubber material in order to improve wettability.

Methods: Samples of experimental silicone rubber were surface modified by first argon plasma treatment followed by chemisorption of ethyleneoxy functional silanes. These were compared with the same silicone rubber which had ethyleneoxy functional surfactants incorporated into the polymer matrix. In all cases contact angles, tear strength and water uptake were measured.

Results: Surface modified materials had comparable contact angles to surfactant modified silicone rubber all being significantly lower than the unmodified material. Surface modified materials, however, had a significantly higher tear strength and lower water uptake in comparison to surfactant modified materials.

Conclusions: Argon plasma treatment followed by chemisorption of ethyleneoxy functional silanes proved an effective way of improving the wettability of an experimental silicone rubber maxillofacial prosthetic material without altering bulk properties.

Download full-text PDF

Source
http://dx.doi.org/10.1016/s03005712(02)00131-8DOI Listing

Publication Analysis

Top Keywords

silicone rubber
24
experimental silicone
16
surface modified
12
ethyleneoxy functional
12
rubber maxillofacial
8
maxillofacial prosthetic
8
argon plasma
8
plasma treatment
8
treatment chemisorption
8
chemisorption ethyleneoxy
8

Similar Publications

Coaxial Direct Ink Writing of Cholesteric Liquid Crystal Elastomers in 3D Architectures.

Adv Mater

January 2025

Department of Materials Science and Engineering, University of Pennsylvania, 3231 Walnut Street, Philadelphia, PA, 19104, USA.

Cholesteric liquid crystal elastomers (CLCEs) hold great promise for mechanochromic applications in anti-counterfeiting, smart textiles, and soft robotics, thanks to the structural color and elasticity. While CLCEs are printed via direct ink writing (DIW) to fabricate free-standing films, complex 3D structures are not fabricated due to the opposing rheological properties necessary for cholesteric alignment and multilayer stacking. Here, 3D CLCE structures are realized by utilizing coaxial DIW to print a CLC ink within a silicone ink.

View Article and Find Full Text PDF

Surface Fluorination of Silicone Rubber with Enhanced Stain Resistance and Slip Properties.

ACS Appl Mater Interfaces

January 2025

State Key Laboratory of Polymer Materials Engineering, College of Polymer Science and Engineering, Sichuan University, Chengdu, Sichuan 610065, P.R. China.

Silicone rubber (SR) holds significant potential for everyday wearable devices due to its inherent sweat resistance and flexibility. However, its broader applicability is constrained by poor oil resistance and a suboptimal slip performance. In this study, we developed an SR with durable oil resistance and enhanced slip properties by forming a covalently bonded barrier layer on its surface through a one-step in situ fluorination reaction using F/N.

View Article and Find Full Text PDF

Effect of Plasma Treatment on Coating Adhesion and Tensile Strength in Uncoated and Coated Rubber Under Aging.

Materials (Basel)

January 2025

Mechanical Engineering Department, Universidad Carlos III de Madrid, 28911 Leganés, Spain.

The degradation of rubber materials under environmental and mechanical stress presents a significant challenge, particularly due to UV (ultraviolet light) exposure, which severely impacts the material's physical properties. This study aims to enhance the UV stability and longevity of rubber by evaluating the performance of modified polyurethane and silicone coatings as protective stabilizers. Natural rubber-styrene-butadiene rubber (NR-SBR), known for its exceptional mechanical properties, was selected as the base material.

View Article and Find Full Text PDF

Inchworm Robots Utilizing Friction Changes in Magnetorheological Elastomer Footpads Under Magnetic Field Influence.

Micromachines (Basel)

December 2024

Department of Mechanical Engineering, Inha University, Incheon 22212, Republic of Korea.

The application of smart materials in robots has attracted considerable research attention. This study developed an inchworm robot that integrates smart materials and a bionic design, using the unique properties of magnetorheological elastomers (MREs) to improve the performance of robots in complex environments, as well as their adaptability and movement efficiency. This research stems from solving the problem of the insufficient adaptability of traditional bionic robots on different surfaces.

View Article and Find Full Text PDF

The advancement of medical 3D printing technology includes several enhancements, such as decreasing the length of surgical procedures and minimizing anesthesia exposure, improving preoperative planning, creating personalized replicas of tissues and bones specific to individual patients, bioprinting, and providing alternatives to human organ transplants. The range of materials accessible for 3D printing within the healthcare industry is significantly narrower when compared with conventional manufacturing techniques. Liquid silicone rubber (LSR) is characterized by its remarkable stability, outstanding biocompatibility, and significant flexibility, thus presenting substantial opportunities for manufacturers of medical devices who are engaged in 3D printing.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!