Unlabelled: Dedicated mammotomography with pinhole incomplete circular orbit (PICO) SPECT imaging of an uncompressed pendant breast was evaluated with small, very-high-stopping-power pinhole apertures. Comparisons were made with planar pinhole scintimammography. Enhanced 3-dimensional imaging performance with very-high-stopping-power apertures is thought to ultimately yield improved sensitivities for lesion detection and identification in breast disease.
Methods: Pinhole collimators made of high-density and high atomic number (184)W or depleted (238)U, with aperture diameters from 1 to 4 mm, were used to image 0.6- and 1.0-cm-diameter spherical lesions in a pendulous, uncompressed breast phantom in planar and PICO-SPECT modes. The breast was centered on the horizontal axis of rotation of an incomplete circular orbit. Lesion, breast and body, and myocardial activities (L:B:M) were included in the phantoms to simulate clinical imaging conditions with (99m)Tc (140 keV). Lesion contrasts and signal-to-noise ratios (SNRs) for all apertures were determined for near clinical acquisition times for L:B:M ratios of 12:1:20 and 7:1:25. A set of minidisks inserted in the breast phantom was scanned to determine sampling limitations at depth from the nipple. In an initial study, a patient with biopsy-confirmed breast carcinoma was injected with 960 MBq (99m)Tc-tetrofosmin and scanned 2 h later with planar pinhole and PICO-SPECT techniques.
Results: Overall, for PICO-SPECT imaging there were small differences in measured counting rate sensitivity (4.9%) and lesion contrast (8.8%) with larger SNR differences (20.8%) between tungsten and depleted uranium pinhole materials at this energy and these lesion sizes. Backgrounds from simulated myocardial uptake had minor contributions in all reconstructed image volumes because of the rapid sensitivity fall-off for pinhole apertures. An optimal aperture diameter between 2 and 3 mm was determined from peak SNR, indicating that these aperture sizes may have the best performance for lesions as small as 0.6 cm in diameter with activity concentration ratios of (99m)Tc similar to those currently seen in patients. Both lesions were visualized with PICO-SPECT better than with planar pinhole imaging, with respective contrast improvements >20 times the values obtained from planar imaging for the same pinholes. In the patient study, higher contrast (>6) visualization of the active tumor periphery was obtained with PICO-SPECT than with planar imaging.
Conclusion: These results indicate that the enhanced spatial resolution of smaller apertures outweighs the loss in sensitivity in small lesion identification with PICO-SPECT. Although the imaging differences between investigated aperture types are small and some limitations to this imaging approach exist, dedicated PICO-SPECT of the breast appears to be an improved technique compared with conventional planar pinhole scintimammography. This technique provides enhanced contrast and SNR for imaging small lesions with the high-resolution pinhole apertures along with 3-dimensional localization of the lesions.
Download full-text PDF |
Source |
---|
Nucl Med Commun
January 2025
Departments of Nuclear Medicine.
Purpose: Parathyroid imaging with dual-phase technetium-99m methoxyisobutrylizonitrile (Tc-99m MIBI) scintigraphy serves as an important prerequisite for the identification of hyperfunctioning parathyroid gland(s) in patients with primary hyperparathyroidism (PHPT) for a successful targeted parathyroidectomy. This study aimed to evaluate the clinical value of additional lateral imaging and single-photon emission computed tomography/computed tomography (SPECT/CT) versus conventional planar imaging for locating parathyroid pathologies in patients with PHPT.
Materials And Methods: A retrospective review was performed on 105 patients who underwent dual-phase Tc-99m MIBI scintigraphy and were surgically treated by parathyroidectomy.
Adv Healthc Mater
October 2024
Centre for Cancer Biology, University of South Australia and SA Pathology, Adelaide, South Australia, 5000, Australia.
While blood-contacting materials are widely deployed in medicine in vascular stents, catheters, and cannulas, devices fail in situ because of thrombosis and restenosis. Furthermore, microbial attachment and biofilm formation is not an uncommon problem for medical devices. Even incremental improvements in hemocompatible materials can provide significant benefits for patients in terms of safety and patency as well as substantial cost savings.
View Article and Find Full Text PDFACS Appl Energy Mater
February 2024
Division of Materials Science, Department of Engineering Sciences and Mathematics, Luleå University of Technology, SE-971 87 Luleå, Sweden.
An inorganic wide-bandgap hole transport layer (HTL), copper(I) thiocyanate (CuSCN), is employed in inorganic planar hydrothermally deposited SbS solar cells. With excellent hole transport properties and uniform compact morphology, the solution-processed CuSCN layer suppresses the leakage current and improves charge selectivity in an n-i-p-type solar cell structure. The device without the HTL (FTO/CdS/SbS/Au) delivers a modest power conversion efficiency (PCE) of 1.
View Article and Find Full Text PDFJ Phys Chem Lett
October 2023
School of New Energy and Materials, Southwest Petroleum University, Chengdu 610500, China.
The aggregation of SnO nanocrystals due to van der Waals interactions is not conducive to the realization of a compact and pinhole-free electron transport layer (ETL). Herein, we have utilized potassium alginate (PA) to self-assemble SnO nanocrystals, forming a PA-SnO ETL for perovskite solar cells (PSCs). Through density functional theory (DFT) calculations, PA can be effectively absorbed onto the surface of SnO.
View Article and Find Full Text PDFJ Colloid Interface Sci
December 2023
School of Instrument Science and Opto-Electronics Engineering, Beijing Information Science & Technology University, Beijing 100192, PR China.
The efficiency and durability of perovskite solar cells (PSCs) are closely related to the property and stability of each functional layer involved in device. Owing to the excellent hole transport properties, the additive-doped Spiro-OMeTAD (2,2',7,7'-tetrakis (N,N-di-p-methoxyphenylamine) 9,9'-spirobifluorene) has become an excellent hole-transporting material for obtaining highly efficient PSCs. However, the hygroscopic nature of additives and the pinholes caused by poor film-forming capability inevitably impair the performance and long-term stability of Spiro-OMeTAD and the resulting PSCs.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!