Objective: The purpose of this study was to investigate the feasibility of a modified microtensile method used to test bond strengths of two current one-bottle dentin bond systems (Prime & Bond NT, PBNT; Prime one Mirage, P-One) with a parallel match design.
Methods: 15 extracted, caries-free human molars were cut to expose occlusal dentin. A 5 mm deep slot was prepared in each crown to divide the crown into nearly equal halves for accepting treatment of the two dentin bond systems, respectively. After 24 h storage in distilled water at 37 degrees C, the bonded teeth were subjected to two treatments: 5 teeth were tested without further treatment and 10 teeth were thermocycled (2400 cycles, between 5 degrees C and 55 degrees C) prior to bond strength testing. Hour-glass shaped specimens with a distance of approximately 1.0 mm at the narrowest portion were cut from each tooth and tested in tensile mode.
Results: Bond strengths (mean MPa) were: for PBNT: 42 & 31, and for P-One 64 & 38 without and with thermocycling, respectively. Two-way ANOVA revealed a significant difference in bond strengths(P < 0.001) between the two systems and when thermocycled. However, a pairwise multiple comparison (Tukey test) showed that after thermocycling the difference between the two systems was not significant (P > 0.05). Regression analysis showed that a correlation existed between the two systems' tensile bond strength values grouped by tooth (correlation coefficient r = 0.575, P < 0.05).
Conclusion: The modified microtensile method with a parallel match design is feasible and suitable for evaluating two different bonding systems or dentin treatments.
Download full-text PDF |
Source |
|---|
Publication Analysis
Top Keywords
Similar Publications
In vitro evaluation of antimicrobial photodynamic therapy with photosensitizers and calcium hydroxide on bond strength, chemical composition, and sealing of glass-fiber posts to root dentin.
Lasers Med Sci
January 2025
Department of Preventive and Restorative Dentistry, Discipline of Endodontics, Araçatuba School of Dentistry, São Paulo State University - UNESP, Araçatuba, SP, Brazil.
Investigate the impact of antimicrobial photodynamic therapy (aPDT) using different photosensitizers (PSs) such as indocyanine green (IG), curcumin (CC), and methylene blue (MB), with or without intracanal application of calcium hydroxide (CH), on the push-out bond strength of glass-fiber posts (GFPs) to intraradicular dentin, the chemical composition of the root substrate, and the sealing of the adhesive interface across different thirds of intraradicular dentin. A total of 112 bovine teeth underwent biomechanical preparation and were divided into eight experimental groups (n = 14 each): Negative control with deionized water; positive control with deionized water + CH; IG group with indocyanine green and infrared laser; IG + CH group; CC group with curcumin and blue LED; CC + CH group; MB group with methylene blue and red laser; and MB + CH group. The push-out bond strength was measured using a universal testing machine (n = 8), and scanning electron microscopy characterized the fracture patterns.
View Article and Find Full Text PDFComparing Sectional and Total Dentin Bond Strengths of Three Endodontic Sealers after Using the Single-cone Obturation Technique: An Study.
J Contemp Dent Pract
October 2024
College of Dentistry, Ajman University, Ajman P.O. Box 346, United Arab Emirates; Department of Endodontic, Faculty of Dentistry, Mansoura University, Egypt, Orcid: https://orcid.org/0000-0003-3391-5306.
Aim: This study aimed to investigate and compare the total and sectional bond strengths of three endodontic sealers when used with the single-cone obturation technique.
Materials And Methods: Forty-five human maxillary central incisors were prepared and divided into three groups according to the type of endodontic sealer: Group I (Gutta-percha/AH Plus Jet), group II (Gutta-percha/GuttaFlow 2), and group III (RealSeal/RealSeal SE). All canals were filled with the single-cone technique.
Effect of Mushroom, Ozone Gas, and Their Combination as Pretreatment Materials on the Bond Strength of Resin Composite to Dentin.
J Contemp Dent Pract
October 2024
Department of Dental Biomaterials, Faculty of Dental Medicine for Girls, Al-Azhar University, Cairo, Egypt, Orcid: https://orcid.org/0000-0002-3420-4146.
Aim: To assess the effect of mushrooms, ozone gas, and their combination as cavity disinfectants on the bonding strength of composite to dentin.
Materials And Methods: The study was conducted on 40 sound premolar teeth randomly divided into four groups. Group I: control group, Group II: mushroom group, Group III: Ozone group, and Group IV: mushroom + ozone gas (combination) group.
Riboflavin-ultraviolet-A collagen crosslinking treatments in improving dentin bonding and resistance to enzymatic digestion.
J Dent Sci
January 2025
School of Dentistry and Institute of Oral Medicine, National Cheng Kung University, Tainan, Taiwan.
Background/purpose: The efficacy of riboflavin-ultraviolet-A (RF-UVA) treatment in crosslinking collagen and improving dentin bonding has been proven. However, biodegradation of the hybrid layer may compromise the bonding. The purpose of this study was to evaluate different RF-UVA treatments regarding their ability to preserve dentin bonding from enzymatic digestion.
View Article and Find Full Text PDFShear bond strength of vat photopolymerization additive-manufactured zirconia to veneering ceramic.
J Prosthodont
January 2025
Department of Prosthodontics, Shanghai Ninth People's Hospital, Shanghai Jiao Tong University School of Medicine; College of Stomatology, Shanghai Jiao Tong University; National Center for Stomatology; National Clinical Research Center for Oral Diseases; Shanghai Key Laboratory of Stomatology; Shanghai Research Institute of Stomatology, Shanghai, PR China.
Purpose: To evaluate the shear bond strength (SBS) of stereolithography (SLA), digital light processing (DLP) manufactured, and computer numerical control (CNC) milled zirconia to veneering ceramic.
Materials And Methods: Rectangular shaped zirconia substrates (10 × 5 × 5 mm) were manufactured through SLA, DLP, and CNC technology separately. Their surface roughness was measured and the surface topography was analyzed by atomic force microscope (AFM).
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!