Vertical concentration profiles of soluble reactive phosphorus (SRP) in the upper sedimentary zone of freshwater lakes are an important means for studying internal phosphorus (P) loading and to gain insight into early diagenetic processes. The interpretation of such pore water profiles generally neglects the occurrence of horizontal variability at a specific sampling site. To further examine this variability, we have designed a novel two-dimensional sampler (2D peeper) consisting of 2280 chambers at a spatial resolution of 9 mm providing a sampling area of 43 x 44 cm. This new device was deployed in three eutrophic lakes in north-eastern Germany. The resulting 2D images of the SRP concentrations, diffusive fluxes, and turnover rates revealed systematic vertical and horizontal structures with local niches of increased phosphorus release. Thus, the extrapolation of P flux calculations based on one-dimensional pore water profiles may lead to a considerable error. The observed small-scale horizontal heterogeneity, probably mainly caused by organisms, was larger in the biologically more active Lake Müllrose and Süsser See than in the deeper Arendsee where meio- and macrozoobenthos were missing. In all cases, the variability was highest at the sediment-water interface and diminished with sediment depth.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1021/es0102538 | DOI Listing |
Chemosphere
January 2025
DASCO Inc, Centennial, Colorado, USA.
This study thoroughly investigated the adsorption of Congo Red (CR) dye onto various microplastics (MPs), including high-density polyethylene (HDPE), polyvinyl chloride (PVC), low-density polyethylene (LDPE), polypropylene (PP) and polyethylene terephthalate (PET). Initial adsorption capacities (q) revealed that HDPE had the highest value (21.90 mg/g), followed by PVC (4.
View Article and Find Full Text PDFWaste Manag
January 2025
Qilu University of Technology (Shandong Academy of Sciences), Advanced Materials Institute, Shandong Engineering Research Centre of Municipal Sludge Disposal, Jinan 250014, China. Electronic address:
Municipal solid waste incineration fly ash (MSWIFA) is considered a hazardous solid waste, traditionally disposed by solidified landfill methods. However, solidified landfills present challenges with leaching heavy metals, polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). To address this issue, this study examined two pretreatment methods for MSWIFA: sintering at 850℃ for 30 min and washing with three water baths (20 min each) at a 3:1 liquid-solid ratio.
View Article and Find Full Text PDFPolymers (Basel)
January 2025
State Key Laboratory of Petroleum Resources and Engineering, China University of Petroleum (Beijing), Beijing 102249, China.
The Bohai oilfield is characterized by severe heterogeneity and high average permeability, leading to a low water flooding recovery efficiency. Polymer flooding only works for a certain heterogeneous reservoir. Therefore, supplementary technologies for further enlarging the swept volume are still necessary.
View Article and Find Full Text PDFPolymers (Basel)
January 2025
Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, Qatar Foundation, Doha P.O. Box 34110, Qatar.
The development of ultrafiltration (UF) polymeric membranes with high flux and enhanced antifouling properties bridges a critical gap in the polymeric membrane fabrication research field. In the present work, the preparation of novel PES membranes incorporated with carrageenan (CAR), which is a natural polymer derived from edible red seaweed, is reported for the first time. The PES/CAR membranes were prepared by using the nonsolvent-induced phase separation (NIPS) method at 0.
View Article and Find Full Text PDFPolymers (Basel)
January 2025
State Key Laboratory of Material Processing and Die & Mold Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China.
Biological surfaces with physical discontinuity or chemical heterogeneity possess special wettability in the form of anisotropic wetting behavior. However, there are several challenges in designing and manufacturing samples with anisotropic wettability. This study investigates the fabrication of PTFE/PDMS grid membranes using Direct Ink Writing (DIW) 3D printing for oil-water separation applications.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!