Background: Tension of the abdominal wall in the inguinal region induced by Shouldice repair of an inguinal hernia is said to be responsible for elevated postoperative pain levels.
Patients And Methods: In 20 patients we recorded the inguinal tensile strength during closure of the hernial gap using a wound retractor equipped with strain gauges. Postoperative pain levels were scaled using a visual analogous score, and correlated with the tensile strength of the inguinal abdominal wall together with peak flow and forced expiratory volume in 1 s (FEV1) 8, 24, and 48 h after the time of operation.
Results: Shouldice repair caused an average increase in inguinal tensile strength of 2.9 +/- 0.58 N (mean +/- SEM). The pain level expressed by active patients was twice the value obtained from resting patients (41.55 +/- 6.3% vs 20.81 +/- 7.1% 8 h after operation), but decreased slightly later on. Peak flow during forced expiration was depressed to about 80% of the control values, whereas the 1-s volume during forced expiration decreased only to 95% of the control value. We excluded any correlation between the recorded individual inguinal tensile strength or the changes in distance between the lateral edge of the rectus sheath and the base of the inguinal ligament and the postoperative pain level.
Conclusion: We failed to see any evidence for the hypothesis that higher inguinal tensile strength induced by Shouldice repair leads to an elevated level of postoperative pain. If there is any effect, it may be masked by other factors with a stronger influence.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s100290100025 | DOI Listing |
Heliyon
January 2025
Faculty of Material and Manufacturing Technologies, Malek Ashtar University of Technology, P.O. Box 1774-15875, Tehran, Iran.
The potential of epoxy-graphene oxide (GO) nanocomposites to improve the mechanical characteristics of conventional epoxy resins is causing them to gain prominence. This makes them appropriate for advanced engineering applications, including structural materials, automotive, and aerospace. This study aimed to develop an epoxy/GO composite with improved mechanical properties through synthesizing epoxy/GO samples with varying GO content (from 0.
View Article and Find Full Text PDFSci Rep
January 2025
Department of Mechanical and Industrial Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, 576104, India.
Fiber-reinforced polymer composites are subjected to harsh environmental conditions over the course of their designed lifespan. Studying the aging process of fiber-reinforced polymer composites exposed to boiling water is critical for improving their durability. This study uses a hand lay-up technique to fabricate composites from glass fiber, bamboo fiber, nanoclay, and epoxy.
View Article and Find Full Text PDFSci Rep
January 2025
Department of General Dentistry, Medical University of Lodz, 251 Pomorska Str, Lodz, 92-213, Poland.
This study aimed at assessing the mechanical properties and degradation of commercial bioactive materials. The bioactive materials (Activa Bioactive Restorative, Beautifil Flow Plus F00, F03, Predicta Bulk Bioactive) and composite resin Filtek Supreme Flow were submitted to flexural and diametral tensile strength tests (FS, DTS), modulus of elasticity (ME) evaluation, and analysis of aging in 70% ethanol and saliva on their hardness and sorption. The results for DTS ranged from 33.
View Article and Find Full Text PDFSci Rep
January 2025
Department of Earth, Environment and Life Sciences, University of Genoa, 16132, Genoa, Italy.
The World Health Organization has confirmed that asbestos fibres are carcinogenic, claiming that asbestos-related diseases should be eradicated worldwide. Actinolite, amosite, anthophyllite, chrysotile, crocidolite, and tremolite are regulated asbestiform mineral phases. However, in nature, asbestos minerals occur either in a fibrous and asbestiform (original morphology characterized by high length-to-width ratio and provided of high tensile strength and flexibility) or fibrous but not asbestiform appearance.
View Article and Find Full Text PDFInt J Biol Macromol
January 2025
Guangxi Key Laboratory of Clean Pulp & Papermaking and Pollution Control, School of Light Industry and Food Engineering, Guangxi University, Nanning 530004, PR China. Electronic address:
Microplastic contamination of low-density polyethylene mulch and nutrient loss from fertilizers present significant challenges in the crop-growing. In this study, the focus was on creating a biodegradable film that combines the advantages of plastic film, thermal insulation and water retention, as well as the controlled release of fertilizer. A key innovation was the efficient introduction of low molecular weight and low dispersibility of poplar lignin into chitosan and polyvinyl alcohol matrices.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!