Safety products have been developed to help reduce the incidence of trauma caused by headgear. Previous studies have reported the characteristics of breakaway-type headgear release mechanisms with axial force application. Not all accidental releases are triggered by an axial force and it is necessary to understand the characteristics of these mechanisms with nonaxial force application. Thirteen headgear release mechanisms were tested as part of a complete headgear system. With the system attached to a plaster head and neck model a tensile force was applied to the system at 30 degrees to the sagittal plane at 2 rates. The force of activation at release and the distance traveled were determined and analyzed statistically. Force values ranged from 4.6 to 36.7 pounds and face bow travel before release ranged from 0.97 to 3.42 inches. No consistent pattern of rate dependence was observed. Several devices demonstrated the desirable combination of low force and face bow travel at release.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1043/0003-3219(2000)070<0377:ROHRMT>2.0.CO;2 | DOI Listing |
Eur J Orthod
March 2022
Faculty of Health Sciences, Institute of Dentistry, University of Eastern Finland, Kuopio, Finland.
Aim: To study the influence of different force magnitudes on dental arches in cervical headgear (CHG) treatment.
Material And Methods: In this controlled clinical trial, patients (n = 40) were treated with CHG with light (L, 300 g, n = 22) or heavy force (H, 500 g, n = 18) magnitude. Subjects were asked to use CHG for 10 hours a day for 10 months.
Ann Biomed Eng
May 2020
George Mason University, Fairfax, VA, USA.
Recently, protective headgear has been released for women's lacrosse despite the fact that contact to the head is illegal. The purposes of this study were to (1) compare the linear and rotational impact attenuation properties of 2 brands of lacrosse headgear at 4 different locations during laboratory pendulum impacts and (2) determine impact dissipation of new and used lacrosse headgear. We measured peak rotational acceleration (PRA; rad/s) and linear acceleration (PLA; g) at 4 impact locations (side, rear boss non-centric (NC), front boss, and front) in two headgear brands (Cascade LX, Hummingbird).
View Article and Find Full Text PDFAm J Orthod Dentofacial Orthop
March 2001
Biomaterials Science Unit, University of Manchester, Dental School, Manchester, UK.
The effect of intraoral aging of biomaterials on the modification of their surface properties has mostly been unknown. The purpose of this study was to investigate and characterize surface alterations of retrieved inner face-bow headgear components. Specimens were prepared from 3 areas of retrieved headgear wires: inner-outer face-bow soldered junction, buccal segment, and projection entering the buccal tube.
View Article and Find Full Text PDFAngle Orthod
October 2000
UCLA Orthodontics, Los Angeles, Cal., USA.
Safety products have been developed to help reduce the incidence of trauma caused by headgear. Previous studies have reported the characteristics of breakaway-type headgear release mechanisms with axial force application. Not all accidental releases are triggered by an axial force and it is necessary to understand the characteristics of these mechanisms with nonaxial force application.
View Article and Find Full Text PDFChest
September 1999
Department of Medicine, Temple University School of Medicine, Philadelphia, PA 19140, USA.
Study Objectives: Previous studies have shown the acute effects of noninvasive positive pressure ventilation (NPPV) in chronic respiratory failure; however, information on the chronic effects of NPPV is limited. We examined the acute and chronic effects of NPPV on gas exchange, functional status, and respiratory mechanics in patients with chronic respiratory failure related to restrictive ventilatory disorders or COPD.
Design: Descriptive analysis of prospectively collected clinical data.
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!