A new method was developed for the fractionation of procyanidin oligomers according to their degree of polymerization. Monomeric flavan-3-ols and low molecular mass procyanidins were selectively extracted from the lyophilized powder of apple condensed tannins (ACTs) by methyl acetate extraction. Sequentially, the separation of each oligomer from dimer to pentamer in this extract was carried out by normal-phase high-performance liquid chromatography using a silica-beads packed column. The best separation was achieved with a mobile phase system containing hexane; (1) hexane-methanol-ethyl acetate, (2) hexane-acetone. These sequential treatments can be easily adapted to large-scale fractionation.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/s0021-9673(00)00614-2 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Experimental Study on the Application of Polymer Agents in Offshore Oil Fields: Optimization Design for Enhanced Oil Recovery.
Polymers (Basel)
January 2025
State Key Laboratory of Petroleum Resources and Engineering, China University of Petroleum (Beijing), Beijing 102249, China.
The Bohai oilfield is characterized by severe heterogeneity and high average permeability, leading to a low water flooding recovery efficiency. Polymer flooding only works for a certain heterogeneous reservoir. Therefore, supplementary technologies for further enlarging the swept volume are still necessary.
View Article and Find Full Text PDFImproved Biomineralization Using Cellulose Acetate/Magnetic Nanoparticles Composite Membranes.
Polymers (Basel)
January 2025
Department of Dental Medicine and Nursing, Faculty of Medicine, Lucian Blaga University of Sibiu, 550169 Sibiu, Romania.
Following implantation, infections, inflammatory reactions, corrosion, mismatches in the elastic modulus, stress shielding and excessive wear are the most frequent reasons for orthopedic implant failure. Natural polymer-based coatings showed especially good results in achieving better cell attachment, growth and tissue-implant integration, and it was found that the inclusions of nanosized fillers in the coating structure improves biomineralization and consequently implant osseointegration, as the nanoparticles represent calcium phosphate nucleation centers and lead to the deposition of highly organized hydroxyapatite crystallites on the implant surface. In this study, magnetic nanoparticles synthesized by the co-precipitation method were used for the preparation of cellulose acetate composite coatings through the phase-inversion method.
View Article and Find Full Text PDFVat photopolymerization (VPP) is an additive manufacturing method that requires the design of photocurable resins to act as feedstock and binder for the printing of parts, both monolithic and composite. The design of a suitable photoresin is costly and time-consuming. The development of one formulation requires the consumption of kilograms of costly materials, weeks of printing and performance testing, as well as the need to have developers with the expertise and knowledge of the materials used, making the development process cost thousands.
View Article and Find Full Text PDFCost-Effective Production of Bacterial Cellulose and Tubular Materials by Cultivating B-11267 on a Molasses Medium.
Polymers (Basel)
January 2025
Department of Biotechnology, Biochemistry and Bioengineering, National Research Ogarev Mordovia State University, 430005 Saransk, Russia.
An original design of a simple bioreactor was used to fabricate two tubular, 200 cm long BC structures by culturing B-11267 on a molasses medium. In addition, a tubular BC-based biocomposite with improved mechanical properties was obtained by combining cultivation on the molasses medium with in situ chemical modification by polyvinyl alcohol (PVA). Moreover, the present study investigated the BC production by the B-11267 strain on the media with different molasses concentrations under agitated culture conditions.
View Article and Find Full Text PDFShifting Focus to Quality: An Innovative Modeling Approach Includes Processing History for Rubber Part Quality Simulation.
Polymers (Basel)
January 2025
Department of Polymer Engineering and Science, Polymer Processing, Montanuniversitaet Leoben, Franz-Josef Strasse 18, 8700 Leoben, Austria.
An innovative modeling approach for the simulative description of the part quality of rubber materials, including the processing history, is presented in this paper. This modeling approach, the so-called average curing speed (ACS) model, is based on the degree of cure and the average curing speed instead of the conventionally considered temperature approach. Such approach neglects the processing history by calculating only the degree of cure.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!