Denture plaque and adherence of Candida albicans to denture-base materials in vivo and in vitro.

Crit Rev Oral Biol Med

Department of Prosthetic Dentistry, Guy's, King's and St. Thomas' Dental Institute, Guy's Dental Hospital, University of London, United Kingdom.

Published: April 2000

The aim of this paper is to review our understanding of the mechanisms and clinical significance of adhesion of C. albicans to denture-base materials in relation to denture plaque and denture-related stomatitis. Earlier reports in the literature of a 65% prevalence level of denture-related stomatitis seem to be exaggerated. More recent studies indicate that denture-related stomatitis is considerably less common, particularly in normal healthy subjects. The etiology of the condition is discussed in this review, and although much of the literature supports the view that the condition is strongly associated with C. albicans, this is not always so. In some subjects, the cause appears to be related to a non-specific plaque. This review also considers the role of denture plaque in the pathogenesis of denture-related stomatitis, the sequential development of denture plaque, and its colonization by Candida organisms. Designing controlled in vivo studies is difficult, and as a consequence, many investigators have had to resort to in vitro studies. The majority of these studies have attempted to investigate the hydrophobicity of C. albicans, relating the surface free-energy of denture-base materials, particularly acrylic resin, to that of the organism. Surprisingly little work has been directed at surface roughness and how it affects retention of organisms. Further, no attention has been paid to the properties and character of the surface, other than average surface roughness, as it affects adhesion. A comparison of results from in vitro studies on the effect on adhesion of pre-coating the surfaces of denture-base materials with saliva has produced equivocal conclusions. This is largely due to little standardization of experimental protocols between studies, particularly in the collection and handling of the saliva used. In conclusion, the review strongly supports the suggestion that adherence of C. albicans to denture-base materials in vitro is related to the hydrophobicity of the organism. The clinical significance of the observation and the mechanisms for the development and maturation of denture plaque are yet to be understood. There is a clear need for further investigation of other factors that may moderate the adhesion of organisms and subsequent colonization of denture-base materials.

Download full-text PDF

Source
http://dx.doi.org/10.1177/10454411990100010501DOI Listing

Publication Analysis

Top Keywords

denture-base materials
24
denture plaque
20
denture-related stomatitis
16
albicans denture-base
12
clinical significance
8
vitro studies
8
surface roughness
8
denture-base
6
materials
6
studies
6

Similar Publications

Development of an antimicrobial tissue conditioner with quaternary ammonium methacryloxy silane (K18): An in vitro study.

J Prosthodont Res

January 2025

Department of Comprehensive Dentistry, UT Health San Antonio, San Antonio, USA.

Purpose: To determine the effects of K18 quaternary ammonium methacryloxy silane (QAS) on tissue conditioner materials and their antimicrobial properties.

Methods: 30% K18 QAS in methyl methacrylate (MMA; K18-MMA; 0%, 15%, and 20% w/w) was incorporated into a commercial tissue conditioner (Coe comfort). The degree of curing (Shore A hardness), hydrophilicity (contact angle), flow, liquid sorption, mass loss, and antimicrobial properties of Streptococcus mutans, Streptococcus sanguinis, and Candida albicans were determined.

View Article and Find Full Text PDF

Purpose: This systematic review evaluated the effect of different printing orientations on the physical-mechanical properties and accuracy of resin denture bases and related specimens.

Study Selection: Utilizing PRISMA 2020 guidelines, a comprehensive search of PubMed, Web of Science, Cochrane, and Scopus databases was conducted until June 2024. Included studies examined the accuracy, volumetric changes, and mechanical or physical properties of 3D-printed denture bases in various orientations.

View Article and Find Full Text PDF

In vitro analysis of composition profiles of resins for 3D printing of dentures.

J Dent

January 2025

Clinic of General-, Special Care- and Geriatric Dentistry, Center for Dental Medicine, University of Zurich, Zurich, Switzerland. Electronic address:

Objective: This study aimed to investigate the resin compounds from CAD-CAM 3D-printed denture resins, focusing on the identification and classification of free monomers and other components. The primary objective was to determine the chemical profile of these 3D-prinding resin materials.

Methods: Four 3D-printed denture resins, two base materials (1: DentaBASE, Asiga Ltd.

View Article and Find Full Text PDF

Wooden Plate Denture Reproduced Using Materials and Methods From 400 Years Ago.

Cureus

December 2024

Department of Oral and Maxillofacial Surgery, National Hospital Organization, Kyoto Medical Center, Kyoto, JPN.

This study aimed to reproduce a complete wooden plate denture, which was the first in the world to retain suction under negative pressure, using the same materials and methods from 400 years ago (i.e., the Edo period) to verify its masticatory performance.

View Article and Find Full Text PDF

This study evaluated the color stability, surface roughness, and hardness of 3D-printed and heat-polymerized denture materials. A total of 90 samples were prepared, with equal numbers of 3D-printed and heat-polymerized disks. The initial hardness, surface roughness, and color values of the samples were measured.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!