In order to bring down the cost of the castings used in fixed partial denture prosthesis, a study was conducted by reusing the nickel chromium alloy without adding any new material. We studied the effect on the ultimate tensile strength, yield strength and modulus of elasticity after reusing the nickel-chromium alloys. Results showed degenerative changes in the properties evaluated after recasting. These changes were statistically significant, suggesting that it can not be reused.
Download full-text PDF |
Source |
|---|
Publication Analysis
Top Keywords
Similar Publications
A process inspired by fractals for embedding digital codes into additively manufactured components for supply chain security.
Sci Rep
January 2025
Refined Imaging LLC, Baton Rouge, LA, 70810, USA.
This study describes procedures for embedding digital information into additively manufactured components as well as procedures for readout and tensile testing. Embedded digital codes were printed inside ASTM E8/E8M dumbbells using Direct Metal Laser Melting (DMLS) with an EOS M290 printer. The codes were configured as either ellipsoids or prolate spheroids in patterns given by the Cantor dust fractal.
View Article and Find Full Text PDFThe Influence of Iron Particles and Polyethylene Glycol on Selected Properties of Polylactide-Based Composites.
Polymers (Basel)
January 2025
Faculty of Mechanical Engineering, Bialystok University of Technology, Wiejska 45C, 15-351 Bialystok, Poland.
This article presents the characteristics of composites comprising polylactide combined with iron powder, from 1 to 10 wt.%, and nanoiron powders with a mass fraction from 0.1 to 1.
View Article and Find Full Text PDFDynamic Tensile Response of Basalt Fibre Grids for Textile-Reinforced Mortar (TRM) Strengthening Systems.
Polymers (Basel)
January 2025
Institute of Science and Innovation in Mechanical and Industrial Engineering (INEGI), FEUP Campus, Rua Dr. Roberto Frias 400, 4200-465 Porto, Portugal.
The present work constitutes the initial experimental effort to characterise the dynamic tensile performance of basalt fibre grids employed in TRM systems. The tensile behaviour of a bi-directional basalt fibre grid was explored using a high-speed servo-hydraulic testing machine with specialised grips. Deformation and failure modes were captured using a high-speed camera.
View Article and Find Full Text PDFMicrostructure and Mechanical Properties of Mg-8Li-3Al-0.3Si Alloy Deformed Through a Combination of Back-Extrusion and Spinning Process.
Materials (Basel)
January 2025
Shanxi Key Laboratory of Magnesium-Based Materials, College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China.
In this work, the Mg-8Li-3Al-0.3Si (LAS830) alloy was prepared by the vacuum melting method. The as-cast alloy was subjected to backward extrusion at 250 °C and then spun at 250 °C.
View Article and Find Full Text PDFEliminating Anisotropy of 7085 Alloy Forgings via Temperature Combination Control During Two-Stage Multi-Directional Forging.
Materials (Basel)
January 2025
National Key Laboratory of Science and Technology on High-Strength Structural Materials, Central South University, Changsha 410083, China.
Due to its high mechanical properties and low quench sensitivity, 7085 aluminum alloy is suitable for the aircraft industry. However, large cross-section forgings of 7085 alloy usually have over 40% anisotropy in mechanical behaviors, especially in the vertical direction. In this study, two-stage multi-directional forgings (MDFs) with different temperature combinations, isothermal medium-temperature composite MDF (MC-MDF) and isothermal hot MDF (H-MDF), were applied to 7085 aluminum alloy ingots.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!