Properties of Cold Sprayed Titanium and Titanium Alloy Coatings after Laser Surface Treatment.

Additive manufacturing (AM) has seen remarkable development in recent years due to relatively high efficiency of the process. Cold spraying (CS) is a particular method of AM, in which titanium and titanium alloy powders are used. CS is a very competitive technology enabling the deposition of coatings, repairing machine parts, and manufacturing new components.

The Impact of Plastic Deformation on the Microstructure and Tensile Strength of Haynes 282 Nickel Superalloy Produced by DMLS and Casting.

The article presents the results of research on the influence of plastic deformation on the microstructure and tensile strength of Haynes 282 nickel superalloy produced by direct metal laser sintering (DMLS) and a conventional technique (casting). Samples were tested for dimensional accuracy using a 3D scanner. Then, the samples were subjected to plastic deformation by rolling.

A Comparative Study of Aluminium and Titanium Warm Sprayed Coatings on AZ91E Magnesium Alloy.

Aluminium (Al) and titanium (Ti) coatings were applied on AZ91E magnesium alloy using a low-pressure warm spray (WS) method. The deposition was completed using three different nitrogen flow rates (NFR) for both coatings. NFR effects on coating microstructure and other physical properties were systematically studied.

Physicochemical Properties of Dentine Subjected to Microabrasive Blasting and Its Influence on Bonding to Self-Adhesive Prosthetic Cement in Shear Bond Strength Test: An In Vitro Study.

The aim of this in vitro study was to assess the influence of microabrasive blasting on the physicochemical properties of dentine and shear bond strength (SBS) of self-adhesive resin cement (Maxcem Elite, Kerr, Orange, CA, USA) bonded to the dentine surface. Ninety cylindrical specimens with exposed dentine of human teeth were prepared and divided into three randomized, parallel sample sets A, B, and C. Groups B and C were subjected to abrasive blasting using a micro-sandblasting device (Microetcher IIa, Danville Materials, Carlsbad, CA, USA) with two gradations of AlO abrasives (Group B, abrasion with a gradation of 50 μm; group C, abrasion with a gradation of 27 μm).

Comparison of Microstructure, Texture, and Mechanical Properties of TZ61 and AZ61 Mg Alloys Processed by Differential Speed Rolling.

In this work, the comparison of microstructure, texture, and mechanical properties of the newly developed TZ61 (Mg-6Sn-1Zn) alloy with the commercially available AZ61 (Mg-6Al-1Zn) has been presented. Both analyzed Mg alloys were processed by conventional symmetric and asymmetric rolling (i.e.

Microstructure and Mechanical Properties of Inverse Nanocomposite Made from Polylactide and Hydroxyapatite Nanoparticles.

Polymer nanocomposites have been extensively researched for a variety of applications, including medical osteoregenerative implants. However, no satisfactory solution has yet been found for regeneration of big, and so-called critical, bone losses. The requirement is to create a resorbable material which is characterised by optimum porosity, sufficient strength, and elastic modulus matching that of the bone, thus stimulating tissue regrowth.

Microstructure, Texture and Mechanical Properties of Mg-6Sn Alloy Processed by Differential Speed Rolling.

The effect of shear deformation introduced by differential speed rolling (DSR) on the microstructure, texture and mechanical properties of Mg-6Sn alloy was investigated. Mg-6Sn sheets were obtained by DSR at speed ratio between upper and lower rolls of R = 1, 1.25, 2 and 3 (R = 1 refers to symmetric rolling).

Strength and thickness of the layer of materials used for ceramic veneers bonding.

The use of adhesive bonding systems and composites in prosthetic dentistry brought improved and more aesthetic prosthetic restorations. The adhesive bonding of porcelain veneers is based on the micromechanical and chemical bond between tooth surface, cement layer and ceramic material. The aim of the study was to measure the thickness of the material layer formed during cementing of a ceramic restoration, and - in the second part of the study - to test tension of these cements.