Compositional analysis of multilayered plastic constituents and constituent mixtures using benchtop H NMR spectroscopy.

Multilayered plastics are widely used in food packaging and other commercial applications due to their tailored functional properties. By layering different polymers, the multilayered composite material can have enhanced mechanical, thermal, and barrier properties compared to a single plastic. However, there is a significant need to recycle these multilayer plastics, but their complex structure offers significant challenges to their successful recycling.

Four buildings and a flush: Lessons from degraded water quality and recommendations on building water management.

A reduction in building occupancy can lead to stagnant water in plumbing, and the potential consequences for water quality have gained increasing attention. To investigate this, a study was conducted during the COVID-19 pandemic, focusing on water quality in four institutional buildings. Two of these buildings were old (>58 years) and large (>19,000 m), while the other two were new (>13 years) and small (<11,000 m).

Chemical characterization of microplastic particles formed in airborne waste discharged from sewer pipe repairs.

Microplastic particles are of increasing environmental concern due to the widespread uncontrolled degradation of various commercial products made of plastic and their associated waste disposal. Recently, common technology used to repair sewer pipes was reported as one of the emission sources of airborne microplastics in urban areas. This research presents results of the multi-modal comprehensive chemical characterization of the microplastic particles related to waste discharged in the pipe repair process and compares particle composition with the components of uncured resin and cured plastic composite used in the process.

Bystander chemical exposures and injuries associated with nearby plastic sewer pipe manufacture: public health practice and lessons.

Cured-in-place pipes (CIPPs) are plastic liners manufactured inside existing damaged sanitary sewer, storm sewer, and water pipes that extend the service life of host pipes. This process often is conducted in neighborhoods and near roadways. Before, during, and after plastic manufacture, waste materials that include volatile materials are released into the air.

Residential Water Softeners Release Carbon, Consume Chlorine, and Require Remediation after Hydrocarbon Contamination.

Water quality impacts of new ion exchange point-of-entry residential softeners and their ability to be decontaminated following hydrocarbon exposure were investigated. During startup, significant amounts of total sulfur (445 ± 815 mg/L) and total organic carbon (937 ± 119 mg/L) were released into the drinking water that flowed through the softeners. Particulate organic carbon was released until the third regeneration cycle, and resin may also have been released.

Pulmonary and neurological health effects associated with exposure to representative composite manufacturing emissions and corresponding alterations in circulating metabolite profiles.

Cured-in-place pipe (CIPP) technology is increasingly being utilized to repair aging and damaged pipes, however, there are concerns associated with the public health hazards of emissions. CIPP installation involves the manufacture of a new plastic composite pipe at the worksite and includes multiple variable components including resin material, curing methods, and operational conditions. We hypothesize styrene-based composite manufacturing emissions (CMEs) will induce greater pulmonary inflammatory responses and oxidative stress, as well as neurological toxicity compared with nonstyrene CMEs.

Regulatory Significance of Plastic Manufacturing Air Pollution Discharged into Terrestrial Environments and Real-Time Sensing Challenges.

Cured-in-place-pipe (CIPP) is an onsite plastic manufacturing technology used in the U.S. and has not been evaluated for regulatory compliance with federal air pollution laws.

Emergency responder and public health considerations for plastic sewer lining chemical waste exposures in indoor environments.

The cured-in-place pipe (CIPP) manufacturing process is used to repair buried pipes, and its waste commonly discharged into the air can enter nearby buildings. Exposure can prompt illness and the need for medical care. A mass balance model was applied to estimate indoor styrene concentrations due to intrusion of CIPP emissions through plumbing under different bathroom ventilation conditions.

An emerging mobile air pollution source: outdoor plastic liner manufacturing sites discharge VOCs into urban and rural areas.

The in situ manufacture of cured-in-place-pipe (CIPP) plastic liners in damaged sewer pipes is an emerging mobile source of anthropogenic air pollution. Evidence indicates volatile organic compounds (VOCs) can be released before, during, and after manufacture. The chemical composition of a popular uncured styrene-based CIPP resin was examined, along with the VOCs that remained in the new cured composite.

Impacts of Municipal Water-Rainwater Source Transitions on Microbial and Chemical Water Quality Dynamics at the Tap.

When rainwater harvesting is utilized as an alternative water resource in buildings, a combination of municipal water and rainwater is typically required to meet water demands. Altering source water chemistry can disrupt pipe scale and biofilm and negatively impact water quality at the distribution level. Still, it is unknown if similar reactions occur within building plumbing following a transition in source water quality.