The Intestinal Barrier Protective Effect of Indole Aldehyde Derivatives on Acute Infection.

Toxoplasmosis, a zoonotic infection caused by (), poses a significant risk to human health and public safety. Despite the availability of clinical treatments, none effectively mitigate the intestinal barrier damage, which is the primary defense against invasion. This study introduced aldehyde groups into the indole scaffold of a peptide-like structure to investigate the protective effects of these indole aldehyde derivatives on the intestinal barrier in mice with acute infection.

An Accurate Non-contact Photoplethysmography via Active Cancellation of Reflective Interference.

Imaging Photoplethysmography (IPPG) is an emerging and efficient optical method for non-contact measurement of pulse waves using an image sensor. While the contactless way brings convenience, the inevitable distance between the sensor and the subject results in massive specular reflection interference on the skin surface, which leads to a low Signal to Interference plus Noise Ratio (SINR) of IPPG. To ease this challenge, this work proposes a novel modulation illumination approach to measure the accurate arterial pulse wave via surface reflection interference isolation from IPPG.

Corrosion Resistance and Mechanical Properties of Cr-Rich 316 Stainless Steel Coatings Fabricated by the TIG Process Using Flux-Cored Wires.

Arc welded 316 stainless steel coatings with flux-cored wires are very promising for marine service environments due to their low cost, high efficiency, and satisfactory performance, while they suffers from Cr dilution during the preparation process. Herein, based on the consideration of increasing the Cr content and ensuring the same value of the Cr/Ni equivalence ratio (Cr/Ni), 316-modified flux-cored wires, 316F (19Cr-12Ni-3Mo) and 316G (22Cr-14Ni-3Mo), were designed under the guidance of a Schaeffler diagram for the improvement of the electrochemical and mechanical properties of 316 stainless steel coatings. The designed flux-cored wires were welded into a three-layer cladding by the tungsten inert gas welding (TIG) process, and the microstructure, corrosion resistance, and mechanical properties of the claddings were investigated.

Polyaniline Induced Trivalent Ni in Laser-Fabricated Nickel Oxides for Efficient Oxygen Evolution Reaction.

Although it is generally acknowledged that transition metals at high oxidation states represent superior oxygen evolution reaction (OER) activity, the preparation and stability of such a high-valence state are still a challenge, which requires relatively harsh reaction conditions and is unstable under ambient conditions. Herein, we report the formation of trivalent nickel (Ni) in laser-fabricated nickel oxides induced by polyaniline (PANI) under electrochemical activation via a significant charge transfer between Ni and N, as confirmed by X-ray photoelectron spectroscopy and density functional theory calculations. Thereafter, the presence of Ni and the improved conductivity by PANI effectively increase the electrochemical OER activity of the samples together with excellent long-term stability.

Fast and Deep Reconstruction of Coprecipitated Fe Phosphates on Nickel Foams for an Alkaline Oxygen Evolution Reaction.

Although there is a general consensus that the electrocatalysts will undergo reconstruction to generate (oxy)hydroxides as real active sites during the electrochemical oxygen evolution reaction (OER), the understanding of this process is still far from satisfactory. In particular, the reconstruction process of most of these electrocatalysts is either slow or occurs only on the surface, which thus restrains the OER performance of the electrocatalysts. Herein, we reveal a fast and deep reconstruction of the coprecipitated Fe phosphates on nickel foam, via in situ Raman spectroscopy together with electron microscopy, X-ray photoelectron spectroscopy, and electrochemical tests.

Wear-Resistant TiC Strengthening CoCrNi-Based High-Entropy Alloy Composite.

In order to improve the wear resistance of CoCrNi alloy, TiC was introduced into the alloy and wear-resistant CoCrNi/(TiC) composites were designed. The effects of TiC contents on the microstructure, mechanical properties, and wear resistance of CoCrNi matrix were investigated, respectively. It was found that the TiC produced dissolution and precipitation process in CoCrNi alloy, and a large number of needled and blocky TiC particles were precipitated in the composites.

Microstructure and Mechanical Properties of Wire Arc Additively Manufactured MoNbTaWTi High Entropy Alloys.

High-temperature resistant high-entropy alloys (HEAs) have attracted extensive attention due to their excellent thermodynamic stability and mechanical properties, especially at high temperatures. However, a highly effective method for large-size HEAs is still desirable but challengeable. This research reported a facile yet effective strategy for MoNbTaWTi HEAs via in-situ wire arc additive manufacturing (WAAM).

Simple and green fabrication process of nano silver conductive ink and the application in frequency selective surface.

A simple and green method for fabrication of nano silver conductive ink was developed for use in frequency selective surface (FSS). The hydrogen peroxide and ethyl cellulose were used as reducing agents and dispersants to synthesize silver nanoparticles (Ag NPs), and the ethyl cellulose was be used as binders of nano silver conductive ink eventually. The reaction byproducts of hydrogen peroxide are water and oxygen, the synthesized Ag NPs were be cleaned using purified water and alcohol without centrifugation and drying process.

Different-Shaped Ultrafine MoNbTaW HEA Powders Prepared via Mechanical Alloying.

Different-shaped ultrafine MoNbTaW high-entropy alloy powders were firstly prepared by a convenient mechanical alloying method. The phase composition and microstructure of the powders were characterized. The powders are ultrafine with nano-sized grains and a good homogeneous microstructure.

Homogenized finite element analysis on effective elastoplastic mechanical behaviors of composite with imperfect interfaces.

A three-dimensional (3D) representative volume element (RVE) model was developed for analyzing effective mechanical behavior of fiber-reinforced ceramic matrix composites with imperfect interfaces. In the model, the fiber is assumed to be perfectly elastic until its tensile strength, and the ceramic material is modeled by an elasto-plastic Drucker-Prager constitutive law. The RVE model is then used to study the elastic properties and the tensile strength of composites with imperfect interfaces and validated through experiments.