Impact of Different Surface Treatments on Shear Bond Strength between Two Zirconia Ceramics and a Composite Material.

The purpose of this study was to compare the surface changes and shear bond strength between a resin composite and two zirconia ceramics subjected to sandblasting and forming gas (5% H in N) plasma surface treatment. Two types of zirconia ceramic specimens (3Y-TZP and (Y,Nb)-TZP) were divided into groups based on the following surface treatment methods: polishing (Control), sandblasting (SB), sandblasting and plasma (SB-P), and plasma treatment (P). Subsequently, chemical surface modification was performed using Clearfil SE Bond (Kuraray, Tokyo, Japan), and the Filtek Z-250 (3M, Maplewood, MN, USA) resin composite was applied.

Correlation of two different devices for the evaluation of primary implant stability depending on dental implant length and bone density: An in vitro study.

Non-invasive objective implant stability measurements are needed to determine the appropriate timing of prosthetic fitting after implant placement. We compared the early implant stability results obtained using resonance frequency analysis (RFA) and damping capacity analysis (DCA) depending on the implant length and bone density. Total 60, 4.

A One-Year Randomized Controlled Clinical Trial of Three Types of Narrow-Diameter Implants for Fixed Partial Implant-Supported Prosthesis in the Mandibular Incisor Area.

Narrow-diameter implants (NDI) serve as a solution for treating limited bone volume in the anterior mandible. This study aimed to evaluate the one-year clinical outcomes of various NDIs in the mandibular incisor area after immediate loading in partially edentulous patients. This single-center, prospective, single-blinded, randomized controlled trial study included 21 patients, with 7 patients in each of the following groups: control (BLT NC SLActive; Straumann), experimental group 1 (CMI IS-III Active S-Narrow; Neobiotech), and experimental group 2 (CMI IS-III Active Narrow; Neobiotech).

Comparison of Implant Surgery Methods of Cortical Tapping and Cortical Widening in Bone of Various Density: A Three-Dimensional Finite Element Study.

Purpose: The primary stability of a dental implant is critical for successful osseointegration during immediate loading. The cortical bone should be prepared to achieve enough primary stability, but not overcompressed. In this study, we investigated the stress and strain distribution in the bone around the implant induced by the occlusal force applied during immediate loading at various bone densities by the FEA method to compare cortical tapping and widening surgical techniques.

Effect of custom abutment data superimposition on the accuracy of implant abutment level scanning: An in vitro study.

Statement Of Problem: When scanning implant abutments, an incomplete scan is often obtained because of a subgingival location or restricted accessibility. Whether these problems can be overcome with a novel scanning technique with digital superimposition of the custom abutment is unclear.

Purpose: The purpose of this in vitro study was to evaluate the effect of the process of superimposing the custom abutment library data onto the scanned abutment data on the accuracy of the digital scan with an intraoral scanner.

Effect of scanning-aid agents on the scanning accuracy in specially designed metallic models: A laboratory study.

The advent of intraoral scanning methods has caused a paradigm shift in dentistry. However, despite their many advantages, intraoral scanners cannot accurately recognize the metallic surfaces of prothesis. Therefore, this experiment was designed to verify the effect of scanning-aid agents on the scanning accuracy using metallic reference models.

Influence of Scanning-Aid Materials on the Accuracy and Time Efficiency of Intraoral Scanners for Full-Arch Digital Scanning: An In Vitro Study.

This study was performed to verify the influence of scanning-aid materials on the accuracy and time efficiency of full-arch scanning with intraoral scanners. The full-arch reference model was constructed by a 3D printer and scanned with a model scanner to obtain the reference dataset. Four experimental groups (application of ScanCure (SC-80, ODS Co, Incheon, Korea), IP Scan Spray (IP-Division, Haimhausen, Germany) and Vita Powder Scan Spray (Vita Zahnfabrik, Stuttgart, Germany), and no treatment) were designed, and the scans were executed (trueness, n = 5) using two intraoral scanners: I500 (Medit Co.

Restoration of a partially edentulous patient with an implant-supported removable partial denture: a case report.

The aim of this report is to present and discuss the clinical procedure of an implant-supported removable partial denture for a partially edentulous patient who exhibited a severely resorbed ridge and a collapsed vertical stop. The 67-year-old partially edentulous patient presented with a lack of vertical stop and an advanced transverse arch discrepancy. For the maxilla, an implant-supported removable partial denture was fabricated on bilateral distal implant abutments.