Impact of Orthodontic-Surgical Treatments on the Signs and Symptoms of Temporomandibular Disorders: A Systematic Review.

Introduction: Some patients exhibit temporomandibular joint or muscular disorders of the masticatory system before, during, or after orthognathic surgery (OS). These are collectively referred to as temporomandibular disorders (TMDs). This systematic literature review aimed to determine the relationship between orthodontic-surgical treatment and TMDs.

Experimental Investigation of Dental Composites Degradation After Early Water Exposure.

While dental composite long-term aging has already been studied in the past, no data exist about the early aging while it might be detrimental regarding the composites' longevity. This study aims to better understand the effects of early water exposure on dental composites. Dental resin composites with different fillers ratio were subjected to water exposure during 24 h, 1 week, or 1 month.

The impact of an underactuated arm exoskeleton on wrist and elbow kinematics during Prioritized Activities of daily living.

This study addresses the feasibility of underactuated arm exoskeletons as an alternative solution to the often bulky and heavy exoskeletons which actuate the shoulder with 3 DoF. Specifically, the study investigates how the wrist and elbow joint adapts their kinematics when the shoulder abduction is constrained. Ten healthy participants conducted three different grasping activities of daily living, during natural motion and during constrained shoulder abduction at two fixed angles: the resting position angle and at an angle of 10 ° abduction from the resting position.

Experimental Bi-axial tensile tests of spinal meningeal tissues and constitutive models comparison.

Introduction This study aims at identifying mechanical characteristics under bi-axial loading conditions of extracted swine pia mater (PM) and dura and arachnoid complex (DAC). Methods 59 porcine spinal samples have been tested on a bi-axial experimental device with a pre-load of 0.01 N and a displacement rate of 0.

Modjaw® device: Analysis of mandibular kinematics recorded for a group of asymptomatic subjects.

Objective: To assess the repeatability and kinematic data of Modjaw® recordings from a group of asymptomatic patients.

Methods: Modjaw® mandibular kinematic data were recorded for 22 asymptomatic volunteers (DC/TMD questionnaire). Sagittal (SCI at 3 and 5 mm) and transversal (TCI at 4 mm) condylar inclination values of the instantaneous center of rotation were measured over two recording sessions.

Update on the parameters influencing the adjustment of the sagittal and transversal condylar inclination of dental articulators.

Objectives: The literature review aimed to compile and summarize the results of research relating to the recordings of condylar displacements obtained with extraoral devices, to guide clinicians to set dental (virtual) articulator parameters. The meta-analysis was undertaken to assess the sagittal condylar inclination (SCI) and transversal condylar inclination (TCI, also known as Bennett angle) values according to horizontal reference planes, movement studied, and patient characteristics: dental status, interocclusal relationship, skeletal pattern, and signs and symptoms of temporomandibular disorders (TMD).

Data Sources: A bibliographic search was conducted in the three following electronic databases: MEDLINE, EMBASE, and Cochrane Library and Best Evidence.

Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model.

With modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method.

A numerical, theoretical and experimental study of the effect of thermocycling on the matrix-filler interface of dental restorative materials.

Objective: Thermocycling is widely used to age dental composites but with very different results from one study to another, even with apparent similar conditions. This study aims at understanding better the relative damaging speed of matrix and fillers, based on theoretical models.

Methods: Eight formulations of an experimental dental material were produced.

Mechanical characterization and identification of material parameters of porcine aortic valve leaflets.

The ideal artificial heart valve does not exist yet. Understanding of mechanical and structural properties of natural tissues is necessary to improve the design of biomimetic aortic valve. Besides these properties are needed for the finite element modeling as input parameters.

Theoretical prediction of dental composites yield stress and flexural modulus based on filler volume ratio.

Objective: A costly advantageous approach in composites development process is to limit experimental tests by predicting mechanical properties with respect to their filler ratio. Models exist for other fields than dentistry. They have been compared to 3-point bending test experimental results for yield stress, flexural modulus and flexural strength.

Diagnosis and management of bruxism: Evaluation of clinical practices in France.

: The Evaluation of Clinical Practice (ECP) conducted with a sample of French general dental practitioners aimed to measure the methods used to diagnose and manage bruxism.: The ECP was performed using a declarative online questionnaire-based anonymous survey (SurveyMonkey) of 1388 practitioners. Twenty-two questions were grouped in 5 categories: (1) Sociodemographic characteristics (Q1-6); (2) Knowledge of the prevalence and definition of bruxism (Q7-9); (3) Diagnostic approach (Q10-11) and management (Q12-Q13); (4) The use of occlusal splints (Q14-21); (5) Oral rehabilitation (Q22).

Material properties of the placenta under dynamic loading conditions.

Trauma during pregnancy especially occurring during car crashes leads to many foetal losses. Numerical modelling is widely used in car occupant safety issue and injury mechanisms analysis and is particularly adapted to the pregnant woman. Material modelling of the gravid uterus tissues is crucial for injury risk evaluation especially for the abruption placentae which is widely assumed as the leading cause of foetal loss.

Stress distribution in the temporo-mandibular joint discs during jaw closing: a high-resolution three-dimensional finite-element model analysis.

Purpose: This study aims at analysing the stresses distribution in the temporomandibular joint (TMJ) using a complete high-resolution finite element model (FE Model). This model is used here to analyse the stresses distribution in the discs during a closing jaw cycle. In the end, this model enables the prediction of the stress evolution in the TMJ disc submitted to various loadings induced by mandibular trauma, surgery or parafunction.

Determination of Young's modulus of mandibular bone using inverse analysis.

Development of a numerical model applicable to clinical practice, and in particular oral implantology, requires knowledge of the mechanical properties of mandibular bone. The wide range of mechanical parameters found in the literature prompted us to develop an inverse analysis method that takes into account the exact geometry of each specimen tested, regardless of its shape. The Young's modulus of 3000MPa we determined for mandibular bone using this approach is lower than the values reported in the literature.