Development of Pyramidal Microwells for Enhanced Cell Spheroid Formation in a Cell-on-Chip Microfluidic System for Cardiac Differentiation of Mouse Embryonic Stem Cells.

Three-dimensional (3D) tissue culture models provide in vivo-like conditions for studying cell physiology. This study aimed to examine the efficiency of pyramidal microwell geometries in microfluidic devices on spheroid formation, cell growth, viability, and differentiation in mouse embryonic stem cells (mESCs). The static culture using the hanging drop (HD) method served as a control.

Novel electroporation microchip with field constriction enhances transfection efficiency and survival rates of feline embryos.

This study introduces a low-voltage electroporation microchip designed for transfection in cat embryos, featuring real-time impedance monitoring. The microchip uses a field constriction strategy, which localises the electric field to the membrane region in contact with the micro-orifice, enhancing electroporation efficiency while minimising damage. Embryos were positioned on the orifice, and a series of voltage pulses (10, 15, and 20 V) were applied.

Application of a novel rectangular filtering microfluidic device for microfilarial detection.

The rectangular filtering microfluidic chip was invented using microfluidics device fabrication technology and can separate living microfilariae from blood samples without a syringe pump. The diagnostic results are highly effective. The device is based on the principle of separating millions of blood cells from microfilariae using a rectangular filter structure.

Effects of Porous Size and Membrane Pattern on Shear Stress Characteristic in Gut-on-a-Chip with Peristalsis Motion.

Dynamic gut-on-a-chip platform allows better recreation of the intestinal environment in vitro compared to the traditional static cell culture. However, the underlying mechanism is still not fully discovered. In this study, the shear stress behavior in a gut-on-a-chip device with porous membrane subjected to peristalsis motion is numerically investigated using CFD simulation for three different pore sizes and two pattern layouts.

Enhancing Performance of a MEMS-Based Piezoresistive Pressure Sensor by Groove: Investigation of Groove Design Using Finite Element Method.

The optimal groove design of a MEMS piezoresistive pressure sensor for ultra-low pressure measurement is proposed in this work. Two designs of the local groove and one design of the annular groove are investigated. The sensitivity and linearity of the sensor are investigated due to the variations of two dimensionless geometric parameters of these grooves.

A simple and high -performance immobilization technique of membrane protein from crude cell lysate sample for a membrane-based immunoassay application.

Membrane proteins are difficult to be extracted and to be coated on the substrate of the immunoassay reaction chamber because of their hydrophobicity. Traditional method to prepare membrane protein sample requires many steps of protein extraction and purification that may lead to protein structure deformation and protein dysfunction. This work proposes a simple technique to prepare and immobilize the membrane protein suspended in an unprocessed crude cell lysate sample.

Hybrid Plasticizers Enhance Specificity and Sensitivity of an Electrochemical-Based Sensor for Cadmium Detection.

In addition to their use as an additive to improve physical properties of solvent polymeric membranes, plasticizers have a considerable impact on the specificity and sensitivity of membrane-modified electrochemical sensors. In this work, we aim at the hybridization of two different plasticizers using the electropolymerization technique in the development of a cadmium(II)-selective electrochemical sensor based on screen-printed gold electrode along with cyclic voltammetric measurement. At this point, we first screen for the primary plasticizer yielding the highest signal using cyclic voltammetry followed by pairing it with the secondary plasticizers giving rise to the most sensitive current response.

Formation of double emulsion micro-droplets in a microfluidic device using a partially hydrophilic-hydrophobic surface.

The objective of this paper is to propose a surface modification method for preparing PDMS microfluidic devices with partially hydrophilic-hydrophobic surfaces for generating double emulsion droplets. The device is designed to be easy to use without any complicated preparation process and also to achieve high droplet encapsulation efficiency compared to conventional devices. The key component of this preparation process is the permanent chemical coating for which the Pluronic surfactant is added into the bulk PDMS.

A miniPCR-Duplex Lateral Flow Dipstick Platform for Rapid and Visual Diagnosis of Lymphatic Filariae Infection.

Lymphatic filariasis (LF) is a neglected major tropical disease that is a leading cause of permanent and long-term disability worldwide. Significant progress made by the Global Programme to Eliminate Lymphatic Filariasis (GPELF) has led to a substantial decrease in the levels of infection. In this limitation, DNA detection of lymphatic filariae could be useful due to it capable of detecting low level of the parasites.

Fabrication of High Aspect Ratio Micro-Structures with Superhydrophobic and Oleophobic Properties by Using Large-Area Roll-to-Plate Nanoimprint Lithography.

Bio-inspired surfaces with superamphiphobic properties are well known as effective candidates for antifouling technology. However, the limitation of large-area mastering, patterning and pattern collapsing upon physical contact are the bottleneck for practical utilization in marine and medical applications. In this study, a roll-to-plate nanoimprint lithography (R2P NIL) process using Morphotonics' automated Portis NIL600 tool was used to replicate high aspect ratio (5.

A Potential Application of Triangular Microwells to Entrap Single Cancer Cells: A Canine Cutaneous Mast Cell Tumor Model.

Cellular heterogeneity is a major hindrance, leading to the misunderstanding of dynamic cell biology. However, single cell analysis (SCA) has been used as a practical means to overcome this drawback. Many contemporary methodologies are available for single cell analysis; among these, microfluidics is the most attractive and effective technology, due to its advantages of low-volume specimen consumption, label-free evaluation, and real-time monitoring, among others.

Investigation of Leukocyte Viability and Damage in Spiral Microchannel and Contraction-Expansion Array.

Inertial separation techniques in a microfluidic system have been widely employed in the field of medical diagnosis for a long time. Despite no requirement of external forces, it requires strong hydrodynamic forces that could potentially cause cell damage or loss during the separation process. This might lead to the wrong interpretation of laboratory results since the change of structures and functional characteristics of cells due to the hydrodynamic forces that occur are not taken into account.

Optimization of 3-aminopropyltriethoxysilane functionalization on silicon nitride surface for biomolecule immobilization.

The 3-aminopropyltriethoxysilane (APTES) is a common method for biomolecule immobilization on silicon and silicon derivatives such as silicon nitride (SiN). However, there are many parameters which impact the efficiency of APTES modification such as APTES concentration and reaction time. Thus, various APTES concentrations (0.

Diagnosis of feline filariasis assisted by a novel semi-automated microfluidic device in combination with high resolution melting real-time PCR.

Background: The diagnosis of filariasis traditionally relies on the detection of circulating microfilariae (mf) using Giemsa-stained thick blood smears. This approach has several limitations. We developed a semi-automated microfluidic device to improve and simplify the detection of filarial nematodes.

The Viability of Single Cancer Cells after Exposure to Hydrodynamic Shear Stresses in a Spiral Microchannel: A Canine Cutaneous Mast Cell Tumor Model.

Our laboratory has the fundamental responsibility to study cancer stem cells (CSC) in various models of human and animal neoplasms. However, the major impediments that spike our accomplishment are the lack of universal biomarkers and cellular heterogeneity. To cope with these restrictions, we have tried to apply the concept of single cell analysis, which has hitherto been recommended throughout the world as an imperative solution pack for resolving such dilemmas.

Chemiluminescence detection with microfluidics for innovative in situ measurement of unbound cobalt ions in dynamic equilibrium with bound ions in binding study with polyethyleneimine and its functionalized nanoparticles.

This work reports a novel method for in situ measurement of binding of cobalt ions to polyethyleneimine (PEI) and polyethyleneimine-functionalized poly (methyl methacrylate) nanoparticles (PEI-NPs) using simple microfluidics with a chemiluminescence detection system. The catalytic effect of free cobalt ion in solution on the luminol-hydrogen peroxide chemiluminescence was employed for the detection of unbound cobalt in dynamic equilibrium with cobalt bound to PEI or PEI-NPs. Many binding measurements lead to incorrect estimation of free metal ions due to insufficient separation of bound and free ions.

Microfluidic Analysis with Front-Face Fluorometric Detection for the Determination of Total Inorganic Iodine in Drinking Water.

A microfluidic method with front-face fluorometric detection was developed for the determination of total inorganic iodine in drinking water. A polydimethylsiloxane (PDMS) microfluidic device was employed in conjunction with the Sandell-Kolthoff reaction, in which iodide catalyzed the redox reaction between Ce(IV) and As(III). Direct alignment of an optical fiber attached to a spectrofluorometer was used as a convenient detector for remote front-face fluorometric detection.

Development of an immunoFET biosensor for the detection of biotinylated PCR product.

ImmunoFET (IMFET) biosensor is a simple platform for the detection of biotinylated products of polymerase chain reaction (PCR). Construction of the IMFET biosensor started with adsorption of 1.5 mg/mL of protein A (PA) onto the insulated gate surface of ISFET for 90 min.

A silicon nitride ISFET based immunosensor for Ag85B detection of tuberculosis.

A silicon nitride Ion Sensitive Field Effect Transistor (ISFET) based immunosensor was developed as a low-cost and label-free electrical detection for the detection of antigen 85 complex B (Ag85B). The sensing membrane of the ISFET was modified with 3-aminopropyltriethoxysilane (APTES) followed by glutaraldehyde (GA), yielding an aldehyde-terminated surface. This group is available for immobilization of a monoclonal antibody against a recombinant Ag85B protein (anti-Ag85B antibody).

Surface modification of silicon dioxide, silicon nitride and titanium oxynitride for lactate dehydrogenase immobilization.

Three different types of surface, silicon dioxide (SiO2), silicon nitride (Si3N4), and titanium oxynitride (TiON) were modified for lactate dehydrogenase (LDH) immobilization using (3-aminopropyl)triethoxysilane (APTES) to obtain an amino layer on each surface. The APTES modified surfaces can directly react with LDH via physical attachment. LDH can be chemically immobilized on those surfaces after incorporation with glutaraldehyde (GA) to obtain aldehyde layers of APTES-GA modified surfaces.

Increasing active surface area to fabricate ultra-hydrophobic surface by using "Black silicon" with bosch etching process.

Needle-shaped pillars so-called "Black silicon" (B-Si) were fabricated by etching cleaned silicon wafer with fluorine-based deep reactive ion etching plasma. The B-Si pillar with the pillar size (a) and spacing (b) of 250 nm, and height (h) of 6.47 microm, coated with SiOxFy film had water contact angle (WCA) and ethylene glycol contact angle (ECA) of 159.

An effect of silicon micro-nano-patterning arrays on superhydrophobic surface.

Superhydrophobic surface can be fabricated by creating a rough surface at very fine scale and modify it with low-surface energy material. To obtain the optimum superhydrophobicity, the surface roughness must be maximized. To avoid the limitation of scaling down the pattern size by using an expensive lithography tools, the surface roughness factor (r) was increased by means of changing an asperity shape so as to increase its overall surface area.