Chemical characterization of polymer and chloride content in waste plastic materials using pyrolysis - direct analysis in real time - high-resolution mass spectrometry.

The increasing global demand for plastic has raised the need for effective waste plastic management due to its long lifetime and resistance to environmental degradation. There is a need for rapid plastic identification to improve the mechanical waste plastic sorting process. This study presents a novel application of Temperature-Programmed Desorption-Direct Analysis in Real Time-High Resolution Mass Spectrometry (TPD-DART-HRMS) that enables rapid characterization of various plastics.

Design of mid-infrared filter array based on plasmonic metal nanodiscs array and its application to on-chip spectrometer.

Mid-infrared wavelengths are called the molecular fingerprint region because it contains the fundamental vibrational modes inherent to the substances of interest. Since the mid-infrared spectrum can provide non-destructive identification and quantitative analysis of unknown substances, miniaturized mid-infrared spectrometers for on-site diagnosis have attained great concern. Filter-array based on-chip spectrometer has been regarded as a promising alternative.

Perovskites fabricated on textured silicon surfaces for tandem solar cells.

The silicon surface texture significantly affects the current density and efficiency of perovskite/silicon tandem solar cells. However, only a few studies have explored fabricating perovskite on textured silicon and the effect of texture on perovskite films because of the limitations of solution processes. Here we produce conformal perovskite on textured silicon with a dry two-step conversion process that incorporates lead oxide sputtering and direct contact with methyl ammonium iodide.

Optimization of tunable guided-mode resonance filter based on refractive index modulation of graphene.

To fabricate a tunable optical filter with a fast response in the near infrared region, a tunable guided-mode resonance (GMR) filter using graphene was proposed and its performance was optimized. In this study, a rigorous coupled wave analysis method was employed to systematically investigate the effects of geometrical configuration of graphene-integrated GMR filters and the optical properties of constituent materials including graphene on their spectral response in terms of tunability and extinction ratio. It was found that as the graphene is located close to the waveguide and the evanescent-field strength at the interface increases, the GMR filter exhibits better tunability.

Random nanohole arrays and its application to crystalline Si thin foils produced by proton induced exfoliation for solar cells.

We report high efficiency cell processing technologies for the ultra-thin Si solar cells based on crystalline Si thin foils (below a 50 µm thickness) produced by the proton implant exfoliation (PIE) technique. Shallow textures of submicrometer scale is essential for effective light trapping in crystalline Si thin foil based solar cells. In this study, we report the fabrication process of random Si nanohole arrays of ellipsoids by a facile way using low melting point metal nanoparticles of indium which were vacuum-deposited and dewetted spontaneously at room temperature.

Thin Ag Precursor Layer-Assisted Co-Evaporation Process for Low-Temperature Growth of Cu(In,Ga)Se Thin Film.

Achieving favorable band profile in low-temperature-grown Cu(In,Ga)Se thin films has been challenging due to the lack of thermal diffusion. Here, by employing a thin Ag precursor layer, we demonstrate a simple co-evaporation process that can effectively control the Ga depth profile in CIGS films at low temperature. By tuning the Ag precursor thickness (∼20 nm), typical V-shaped Ga gradient in the copper indium gallium diselenide (CIGS) film could be substantially mitigated along with increased grain sizes, which improved the overall solar cell performance.

Enhanced efficiency of crystalline Si solar cells based on kerfless-thin wafers with nanohole arrays.

Several techniques have been proposed for kerfless wafering of thin Si wafers, which is one of the most essential techniques for reducing Si material loss in conventional wafering methods to lower cell cost. Proton induced exfoliation is one of promising kerfless techniques due to the simplicity of the process of implantation and cleaving. However, for application to high efficiency solar cells, it is necessary to cope with some problems such as implantation damage removal and texturing of (111) oriented wafers.

Electrical analysis of c-Si/CGSe monolithic tandem solar cells by using a cell-selective light absorption scheme.

A monolithic tandem solar cell consisting of crystalline Si (c-Si)/indium tin oxide (ITO)/CuGaSe (CGSe) was demonstrated by stacking a CGSe solar cell on a c-Si/ITO solar cell to obtain a photovoltaic conversion efficiency of about 10%. Electrical analyses based on cell-selective light absorption were applied to individually characterize the photovoltaic performances of the top and bottom subcells. Illumination at a frequency that could be absorbed only by a targeted top or bottom subcell permitted measurement of the open-circuit voltage of the target subcell and the shunt resistance of the non-target subcell.

Completely transparent conducting oxide-free and flexible dye-sensitized solar cells fabricated on plastic substrates.

To achieve commercialization and widespread application of next-generation photovoltaics, it is important to develop flexible and cost-effective devices. Given this, the elimination of expensive transparent conducting oxides (TCO) and replacement of conventional glass substrates with flexible plastic substrates presents a viable strategy to realize extremely low-cost photovoltaics with a potentially wide applicability. To this end, we report a completely TCO-free and flexible dye-sensitized solar cell (DSSC) fabricated on a plastic substrate using a unique transfer method and back-contact architecture.

Silicon nanodisk array design for effective light trapping in ultrathin c-Si.

The use of ultrathin c-Si (crystalline silicon) wafers thinner than 20 μm for solar cells is a very promising approach to realize dramatic reduction in cell cost. However, the ultrathin c-Si requires highly effective light trapping to compensate optical absorption reduction. Conventional texturing in micron scale is hardly applicable to the ultrathin c-Si wafers; thus, nano scale texturing is demanded.

Characterization of efficiency-limiting resistance losses in monolithically integrated Cu(In,Ga)Se2 solar modules.

The cell-to-module efficiency gap in Cu(In,Ga)Se2 (CIGS) monolithically integrated solar modules is enhanced by contact resistance between the Al-doped ZnO (AZO) and Mo back contact layers, the P2 contact, which connects adjacent cells. The present work evaluated the P2 contact resistance, in addition to the TCO resistance, using an embedded transmission line structure in a commercial-grade module without using special sample fabrication methods. The AZO layers between cells were not scribed; instead, the CIGS/CdS/i-ZnO/AZO device was patterned in a long stripe to permit measurement of the Mo electrode pair resistance over current paths through two P2 contacts (Mo/AZO) and along the AZO layer.

An equivalent configuration approach for the moiré patterns appearing due to the reflecting surface in display system.

A new moiré pattern appearing in the off-state of a display system with a reflecting surface under illumination of an external ambient light source was analyzed. The origin of the new moiré pattern was attributed to the moiré pattern which is formed on the reflecting surface by external light and plays as a new light source with intensity profile. Configuring an optically equivalent system with no reflecting surface layer was proposed in order to overcome the limitation of new simulation program, which was previously proved to be very efficient in computation time but unable to handle a non-sequential system containing a reflecting surface.

Detection of amyloid-β42 using a waveguide-coupled bimetallic surface plasmon resonance sensor chip in the intensity measurement mode.

The waveguide-coupled bimetallic (WcBiM) surface plasmon resonance (SPR) chip had been utilized in the intensity interrogation detection mode to detect amyloid-β42 (Aβ42), a biomarker of the Alzheimer disease. The SPR reflectance curve of the WcBiM chip has the narrower full-width-at-half-maximum (FWHM) compared with the SPR reflectance curve of the conventional gold (Au) chip, resulting in the steeper gradient. For the enhancement of resolution, the light source was fixed at an angle where the slope of the reflectance curve is the steepest, and the change in the reflectance was monitored.

An efficient simulation and analysis method of moiré patterns in display systems.

A precise and fast computational method for the simulation and analysis of moiré patterns is proposed. This new algorithm is based on convolution with superposition of the intensity profile which is transmitted from the optical layers and the point spread function. The computational time is shown to be much faster than that of the ray-tracing algorithm because the new algorithm does not involve a massive calculation.

Optical design of transparent metal grids for plasmonic absorption enhancement in ultrathin organic solar cells.

Transparent metal grid combining with plasmonic absorption enhancement is a promising replacement to indium tin oxide thin films. We numerically demonstrate metal grids in one or two dimension lead to plasmonic absorption enhancements in ultrathin organic solar cells. In this paper, we study optical design of metal grids for plasmonic light trapping and identify different plasmonic modes of the surface plasmon polaritons excited at the interfaces of glass/metal grids, metal grids/active layers, and the localized surface plasmon resonance of the metal grids using numerical calculations.

Enhancing performance of a miniaturized surface plasmon resonance sensor in the reflectance detection mode using a waveguide-coupled bimetallic chip.

The characteristics of a waveguide-coupled bimetallic (WcBiM) chip in a miniaturized surface plasmon resonance (SPR) sensor and its detection capability for a low molecular weight biomolecule were investigated. The configuration of the WcBiM chip was gold (Au)/waveguide (ZnS-SiO2)/silver (Ag). In the intensity measurement mode, the sensitivity could be improved by reducing the full width at half maximum (FWHM) of the reflectance curve.

Fiber-optic waveguide coupled surface plasmon resonance sensor.

A novel approach to give an excellent tunability and self-referencing capability was presented by applying a concept of waveguide coupled surface plasmon resonance mode to a fiber-optic sensor. The presence of dielectric waveguide sandwiched between two metal layers made it possible to precisely tune the resonance wavelength in a broad range from visible to infrared region and to generate multiple modes which may be selectively used for suitable applications. Our approach also verified the potential capability of self-referencing based on a remarkable difference in sensitivity between the plasmonic and waveguide modes excited by p- and s-polarized lights, respectively, without using an additional reference channel.

Properties of ZnO thin films co-doped with hydrogen and fluorine.

ZnO films co-doped with fluorine and hydrogen were prepared on Corning glass by radio frequency magnetron sputtering of ZnO targets with varying amounts of ZnF2 in H2/Ar gas mixtures of varying H2 content. The ZnO films' electrical, optical, and structural properties in combination with their compositional properties were investigated. A small addition of H2 to the sputtering gas caused a drastic increase of Hall mobility with a marginal increase in carrier concentration, indicating an effective passivation of grain boundaries due to hydrogenation.

An efficient ray tracing algorithm for the simulation of light trapping effects in Si solar cells with textured surfaces.

Optimizing the design of the surface texture is an essential aspect of Si solar cell technology as it can maximize the light trapping efficiency of the cells. The proper simulation tools can provide efficient means of designing and analyzing the effects of the texture patterns on light confinement in an active medium. In this work, a newly devised algorithm termed Slab-Outline, based on a ray tracing technique, is reported.

Method to protect charge recombination in the back-contact dye-sensitized solar cell.

We prepared a back-contact dye-sensitized solar cell and investigated effect of the sputter deposited thin TiO₂ film on the back-contact ITO electrode on photovoltaic property. The nanocrystalline TiO₂ layer with thickness of about 11 μm formed on a plain glass substrate in the back-contact structure showed higher optical transmittance than that formed on an ITO-coated glass substrate, which led to an improved photocurrent density by about 6.3%.

Resolution enhancement in surface plasmon resonance sensor based on waveguide coupled mode by combining a bimetallic approach.

In this study, we present and demonstrate a new route to a great enhancement in resolution of surface plasmon resonance sensors. Basically, our approach combines a waveguide coupled plasmonic mode and a kind of Au/Ag bimetallic enhancement concept. Theoretical modeling was carried out by solving Fresnel equations for the multilayer stack of prism/Ag inner-metal layer/dielectric waveguide/Au outer-metal layer.

Toward understanding the mechanism of nonlinear optical characteristics of PbTe thin film for nano-optical memory.

An experimental study is conducted toward understanding the mechanism of nonlinear optical properties of PbTe thin film that were demonstrated potentially usable for nano-optical memory based on super-resolution technology. By way of a real time optical-electrical characterization of a PbTe thin film device, it is found that absorption coefficient decreases with increasing laser power, accompanied by increase in carrier concentration. From z-scan measurements, nonlinear optical coefficient due to a long pulse (1 micros) z-scan is found nearly 3 order of magnitude higher than the one due to a short pulse (30 ps) z-scan when input energy density is relatively comparable.