Green Chemistry to Modify Functional Properties of Crambe Protein Isolate-Based Thermally Formed Films.

Proteins are promising precursors to be used in production of sustainable materials with properties resembling plastics, although protein modification or functionalization is often required to obtain suitable product characteristics. Here, effects of protein modification were evaluated by crosslinking behavior using high-performance liquid chromatography (HPLC), secondary structure using infrared spectroscopy (IR), liquid imbibition and uptake, and tensile properties of six crambe protein isolates modified in solution before thermal pressing. The results showed that a basic pH (10), especially when combined with the commonly used, although moderately toxic, crosslinking agent glutaraldehyde (GA), resulted in a decrease in crosslinking in unpressed samples, as compared to acidic pH (4) samples.

Functionalization Routes for Keratin from Poultry Industry Side-Streams-Towards Bio-Based Absorbent Polymers.

Keratin is a largely available protein that can be obtained from the ca. 3 million tons of feathers that the European poultry industry produces as a side-stream. Here, the functionalization of keratin from poultry feathers was evaluated using a one- versus two-stage process using two functionalization agents (succinic anhydride-SA and ethylene dianhydride-EDTAD).

Protein Fractionation of Green Leaves as an Underutilized Food Source-Protein Yield and the Effect of Process Parameters.

Green biomass has potential as a sustainable protein source for human consumption, due to its abundance and favorable properties of its main protein, RuBisCO. Here, protein fractionation outcomes of green leafy biomass from nine crops were evaluated using a standard protocol with three major steps: juicing, thermal precipitation, and acid precipitation. Successful protein fractionation, with a freeze-dried, resolubilized white protein isolate containing RuBisCO as the final fraction, was achieved for seven of the crops, although the amount and quality of the resulting fractions differed considerably between crops.

Acylation of agricultural protein biomass yields biodegradable superabsorbent plastics.

Superabsorbent polymers (SAP) are a central component of hygiene and medical products requiring high liquid swelling, but these SAP are commonly derived from petroleum resources. Here, we show that sustainable and biodegradable SAP can be produced by acylation of the agricultural potato protein side-stream (PPC) with a non-toxic dianhydride (EDTAD). Treatment of the PPC yields a material with a water swelling capacity of ca.

Extrusion of Porous Protein-Based Polymers and Their Liquid Absorption Characteristics.

The production of porous wheat gluten (WG) absorbent materials by means of extrusion processing is presented for the future development of sustainable superabsorbent polymers (SAPs). Different temperatures, formulations, and WG compositions were used to determine a useful protocol that provides the best combination of porosity and water swelling properties. The most optimal formulation was based on 50 wt.

Carboxylated Wheat Gluten Proteins: A Green Solution for Production of Sustainable Superabsorbent Materials.

Functionalized wheat gluten (WG) protein particles with the ability to absorb fluids within the superabsorbent range are presented. Ethyleneditetraacetic dianhydride (EDTAD), a nontoxic acylation agent, was used for the functionalization of the WG protein at higher protein content than previously reported and no additional chemical cross-linking. The 150-550 μm protein particles had 50-150 nm nanopores induced by drying.

Superabsorbent and Fully Biobased Protein Foams with a Natural Cross-Linker and Cellulose Nanofibers.

The development of fully natural wheat gluten foams showing rapid and high uptake of water, sheep blood, and saline solution, while maintaining high mechanical stability in the swollen state, is presented. Genipin was added as a natural and polar cross-linker to increase the polarity of the protein chains, whereas cellulose nanofibers (CNFs) were added as a reinforcement/stiffener of the foams, alone or in combination with the genipin. The presence of only genipin resulted in a foam that absorbed up to 25 g of water per gram of foam and a more than 15 g uptake in only 8 min.

Film Extrusion of Crambe abyssinica/Wheat Gluten Blends.

Crambe abyssinica is a plant with potential for use in industrial (non-food) plant oil production. The side stream from this oil production is a high-protein crambe meal that has limited value, as it is not fit for food or feed use. However, it contains proteins that could potentially make it a suitable raw material for higher-value products.

Macromolecular changes and nano-structural arrangements in gliadin and glutenin films upon chemical modification: Relation to functionality.

Protein macromolecules adopted for biological and bio-based material functions are known to develop a structured protein network upon chemical modification. In this study, we aimed to evaluate the impact of chemical additives such as, NaOH, NH4OH and salicylic acid (SA), on the secondary and nano-structural transitions of wheat proteins. Further, the effect of chemically induced modifications in protein macromolecular structure was anticipated in relation to functional properties.

Economically viable components from Jerusalem artichoke (Helianthus tuberosus L.) in a biorefinery concept.

Biorefinery applications are receiving growing interest due to climatic and waste disposal issues and lack of petroleum resources. Jerusalem artichoke (Helianthus tuberosus L.) is suitable for biorefinery applications due to high biomass production and limited cultivation requirements.

Effect of additives on the tensile performance and protein solubility of industrial oilseed residual based plastics.

Ten chemical additives were selected from the literature for their proposed modifying activity in protein-protein interactions. These consisted of acids, bases, reducing agents, and denaturants and were added to residual deoiled meals of Crambe abyssinica (crambe) and Brassica carinata (carinata) to modify the properties of plastics produced through hot compression molding at 130 °C. The films produced were examined for tensile properties, protein solubility, molecular weight distribution, and water absorption.