Design and Implementation of C-Band Large-Power Planar Butler Matrix in SRS.

In satellite remote sensing (SRS), there is a demand for large-power microwave components. A Butler matrix is essential to a transmitting antenna array in SRS. This article illustrates the electrical and mechanical design, simulation, and test results of a large-power planar beamforming network for SRS at C-band.

Modelling energy deposition in polymethyl methacrylate with low-energy electron irradiation.

Energy deposition in dielectric materials by electron irradiation is important in evaluating irradiation effects in various applications. Herein, we developed a novel Monte Carlo model to calculate the actual distribution of energy deposition in polymethyl methacrylate (PMMA) by simulating low-energy electron transport, including secondary electron cascades. We compared the energy deposition calculated using this model with the distribution of energy loss based on the continuous slowing down approximation (CSDA).

Experimental research on influence of gas adsorption on secondary electron emission of copper surface.

Secondary electron (SE) emission is a superficial physical phenomenon. The range of SEs excited in materials which are finally emitted from the surface is generally within a few tens of nanometers. SE emission from materials by electron irradiation has great dependence on surface quality, such as gas adsorption, oxidation, contamination, and morphology.

Electron beam irradiation on novel coronavirus (COVID-19): A Monte-Carlo simulation.

The novel coronavirus pneumonia triggered by COVID-19 is now raging the whole world. As a rapid and reliable killing COVID-19 method in industry, electron beam irradiation can interact with virus molecules and destroy their activity. With the unexpected appearance and quickly spreading of the virus, it is urgently necessary to figure out the mechanism of electron beam irradiation on COVID-19.

Effect of Sputtering Temperature on Fluorocarbon Films: Surface Nanostructure and Fluorine/Carbon Ratio.

In this work, fluorocarbon film was deposited on silicon (P/100) substrate using polytetrafluoroethylene (PTFE) as target material at elevated sputtering temperature. Field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were employed to investigate the surface morphology as well as structural and chemical compositions of the deposited film. The surface energy, as well as the polar and dispersion components, were determined by water contact angle (WCA) measurement.

Voltage Control of Magnetic Anisotropy through Ionic Gel Gating for Flexible Spintronics.

In spite of recent rapid development of flexible electronics, voltage-tunable spintronic structures and devices on flexible substrates have been rarely studied. Here, voltage control of magnetic anisotropy (VCMA) is demonstrated via ionic gel (IG) gating on flexible polyimide substrates with a circuit operating voltage of 1.8 V.

Fabrication of Porous Ag/TiO/Au Coatings with Excellent Multipactor Suppression.

Porous Ag/TiO/Au coatings with excellent multipactor suppression were prepared by fabrication of porous Ag surface through two-step wet chemical etching, synthesis of TiO coatings by electroless-plating-like solution deposition and deposition of Au coatings via electroless plating. Porous structure of Ag surface, TiO coatings on porous Ag surface and Au coatings on porous Ag/TiO surface were verified by field-emission scanning electron microscopy, the composition and crystal type of TiO coatings was characterized by X-ray photoelectron spectroscopy and X-ray diffraction. Secondary electron yield (SEY) measurement was used to monitor the SEY coefficient of the porous Ag coatings and Ag/TiO/Au coatings.

Influence of surface topography on the secondary electron yield of clean copper samples.

Secondary electron yield (SEY) due to electron impact depends strongly on surface topography. The SEY of copper samples after Ar-ion bombardment is measured in situ in a multifunctional ultrahigh vacuum system. Increasing the ion energy or duration of ion bombardment can even enlarge the SEY, though it is relatively low under moderate bombardment intensity.

Heating-induced variations of secondary electron emission from ion-cleaned copper samples.

Secondary electron (SE) emission due to electron impact depends strongly on surface conditions. The variations of SE yield and spectrum with the heating temperature of Ar-ion-cleaned oxygen-free copper samples are therefore measured in situ in a multifunctional ultrahigh vacuum system. The SE yield and the SE spectrum are observed to increase and to narrow, respectively, after sample heating.

Note: measuring effects of Ar-ion cleaning on the secondary electron yield of copper due to electron impact.

In a measurement system of total secondary electron yield (SEY) with in situ ion cleaning, we investigate SEY characteristics of the Cu samples cleaned at different Ar-ion energies and cleaning time. Measured SEY data are compared with those before cleaning and simulated with the Monte Carlo method for an ideal surface of copper. We find that weakening the cleaning intensity, i.

Rainbow-like radiation from an omni-directional source placed in a uniaxial metamaterial slab.

In this paper, the radiation of an omni-directional line source placed in a uniaxial metamaterial slab is experimentally presented. The anisotropic slab made of metallic symmetrical rings with dispersive permeability is investigated both theoretically and experimentally. For low value of the permeability, a directive radiation at the broadside of the slab can be obtained.