Impression Disinfection and Its Effect on Dimensional Accuracy and Surface Detail in the Times of COVID-19: An In Vitro Study.

Introduction The disinfection of impressions is crucial to eliminate the viral and other microbial loads to prevent the cross contamination of diseases. The aim of this study was to compare the effect of different virucidal disinfecting methods on the dimensional accuracy and surface detail reproduction (SDR) of impression materials. Methods A total of 160 samples were fabricated with different impression materials using zinc oxide eugenol (Group 1), alginate (Group 2), polyether (Group 3), and addition silicone (Group 4) impression materials, each containing 40 samples (n=40).

Comparative analysis of shear bond strength of lithium disilicate samples cemented using different resin cement systems: An study.

Aim: This study aims to evaluate and compare the shear bond strength (SBS) of three different resin cements - total etch and rinse, self-etch and self-adhesive resin cements, used to bond the lithium disilicate restorations to human dentin.

Settings And Design: Comparative - study design.

Materials And Methods: Forty-five lithium disilicate (IPS E.

Evaluation of the effect of implant angulations and impression techniques on implant cast accuracy - An study.

Aim: The purpose of this study was to evaluate the accuracy of implant casts generated with splinted and nonsplinted impression techniques with multiple parallel and nonparallel implants.

Materials And Methods: In this experimental study, two edentulous maxillary stainless steel models with seven implant analogs in the central incisor, canine, premolar, and first molar region simulating clinical condition were used (control groups). In one master model, implant analogs were placed parallel to each other, whereas in another model, analogs were placed with a tilt-to-longitudinal axis.

Comparative evaluation of the influence of immediate versus delayed loading protocols of dental implants: A radiographic and clinical study.

Aim: Immediate loading protocol, in recent times, has gained popularity as it has not only shortened the treatment time but also resulted in enhanced patient satisfaction. The aim of this study was to evaluate and compare the effectiveness of immediate implant loading protocol over conventional implant loading protocol with respect to peri-implant bone loss.

Materials And Methods: Twenty patients selected for this study were divided into two groups.

Comparison of marginal and internal adaptation of copings fabricated from three different fabrication techniques: An study.

Aim: The purpose of this study was to compare the marginal and internal adaptation of cobalt-chromium (Co-Cr) copings fabricated from conventional wax pattern, three-dimensional (3D)-printed resin pattern, and laser sintering technique.

Materials And Methods: A total of thirty copings were made, out of which ten copings were made from 3D-printed resin pattern (Group A), ten from inlay wax pattern (Group B), and ten copings were obtained from direct metal laser sintering (DMLS) technique (Group C). All the thirty samples were seated on their respective dies and sectioned carefully using a laser jet cutter and were evaluated for marginal and internal gaps at the predetermined areas using a stereomicroscope.

Evaluation of fracture resistance of ceramic veneers with different preparation designs and loading conditions: An study.

Purpose: The purpose of this study was to evaluate the effect of incisal butt joint and incisal overlap design on the fracture resistance of ceramic veneers under two different loading conditions, i.e., 125° and 60° representing protrusive and intercuspal movements, respectively.

A finite element study of teeth restored with post and core: Effect of design, material, and ferrule.

Background: Different postdesigns and materials are available; however, no consensus exists regarding superiority for stress distribution. The aim of this study was to evaluate the effect of design and material of post with or without ferrule on stress distribution using finite element analysis.

Materials And Methods: A total of 12 three-dimensional (3D) axisymmetric models of postretained central incisors were made: Six with ferrule design and six without it.

Comparative evaluation of marginal leakage of provisional crowns cemented with different temporary luting cements: In vitro study.

Background Or Statement Of Problem: As, the longevity of provisional restorations is related to, a perfect adaptation and a strong, long-term union between restoration and teeth structures, therefore, evaluation of marginal leakage of provisional restorative materials luted with cements using the standardized procedures is essential.

Aims And Objectives: To compare the marginal leakage of the provisional crowns fabricated from Autopolymerizing acrylic resin crowns and bisphenol A-glycidyl dimethacrylate (BIS-GMA) resin crowns. To compare the marginal leakage of the provisional crowns fabricated from autopolymerizing acrylic resin crowns and BIS-GMA resin crowns cemented with different temporary luting cements.

Subway mandibular buccal defect blocked with two part prosthesis unified by Earth magnets.

This clinical report describes the fabrication of a two-piece obturator used to close the mandibular buccal defect. Two-piece obturator prosthesis was fabricated with clear heat cure acrylic resin to be used during the healing period following the marsupialization of odontogenic keratocyst which had lead to the loss of portions of the mandibular buccal region. The prosthesis fabricated in two parts was joined by the rare earth magnets.