An Automated Microfluidic Analyzer for Monitoring of Total Alkalinity.

We have designed, built, tested, and deployed an autonomous analyzer for seawater total alkalinity. Such analyzers are required to understand the ocean carbon cycle, including anthropogenic carbon dioxide (CO) uptake and for mitigation efforts via monitoring, reporting, and verification of carbon dioxide removal through ocean alkalinity enhancement. The microfluidic nature of our instrument makes it relatively lightweight, reagent efficient, and amenable for use on platforms that would carry it on long-term deployments.

Simultaneous Absorbance and Fluorescence Measurements Using an Inlaid Microfluidic Approach.

A novel microfluidic optical cell is presented that enables simultaneous measurement of both light absorbance and fluorescence on microlitre volumes of fluid. The chip design is based on an inlaid fabrication technique using clear and opaque poly(methyl methacrylate) or PMMA to create a 20.2 mm long optical cell.

An Energy Efficient Thermally Regulated Optical Spectroscopy Cell for Lab-on-Chip Devices: Applied to Nitrate Detection.

Reagent-based colorimetric analyzers often heat the fluid under analysis for improved reaction kinetics, whilst also aiming to minimize energy use per measurement. Here, a novel method of conserving heat energy on such microfluidic systems is presented. Our design reduces heat transfer to the environment by surrounding the heated optical cell on four sides with integral air pockets, thereby realizing an insulated and suspended bridge structure.

A Magnetically Tunable Check Valve Applied to a Lab-on-Chip Nitrite Sensor.

Presented here is the fabrication and characterization of a tunable microfluidic check valve for use in marine nutrient sensing. The ball-style valve makes use of a rare-earth permanent magnet, which exerts a pulling force to ensure it remains passively sealed until the prescribed cracking pressure is met. By adjusting the position of the magnet, the cracking pressure is shown to be customizable to meet design requirements.

Determination of boron concentration in oilfield water with a microfluidic ion exchange resin instrument.

We developed and validated a microfluidic instrument for interference-free determination of boron in produced water. The instrument uses a boron-specific chelating resin to separate the analyte from its complex matrix. Ten produced water samples were analyzed with the instrument and the results were successfully validated against ICP-MS measurements.

Determination of boron in produced water using the carminic acid assay.

Using the carminic acid assay, we determined the concentration of boron in oilfield waters. We investigated the effect of high concentrations of salts and dissolved metals on the assay performance. The influence of temperature, development time, reagent concentration, and water volume was studied.

Asphaltenes yield curve measurements on a microfluidic platform.

We describe a microfluidic apparatus and method for performing asphaltene yield measurements on crude oil samples. Optical spectroscopy measurements are combined with a microfluidic fluid handling platform to create an automated microfluidic apparatus to measure the asphaltene yield. The microfluidic measurements show good agreement with conventional wet chemistry measurements as well as available models.

A high performance microfluidic analyser for phosphate measurements in marine waters using the vanadomolybdate method.

We report a high performance autonomous analytical system based on the vanadomolybdate method for the determination of soluble reactive phosphorus in seawater. The system combines a microfluidic chip manufactured from tinted poly (methyl methacrylate) (PMMA), a custom made syringe pump, embedded control electronics and on-board calibration standards. This "lab-on-a-chip" analytical system was successfully deployed and cross-compared with reference analytical methods in coastal (south west England) and open ocean waters (tropical North Atlantic).

Measurement of asphaltenes using optical spectroscopy on a microfluidic platform.

We present a microfluidic apparatus and method for the measurement of asphaltene content in crude-oil samples. The measurement is based on an optical absorption technique, where it was established that asphaltene coloration correlated linearly with asphaltene weight content. The initial absorbance of the oil is measured, and asphaltenes are removed from the oil by the addition of n-alkane, leading to flocculation and subsequent filtration.

Lab-on-chip measurement of nitrate and nitrite for in situ analysis of natural waters.

Microfluidic technology permits the miniaturization of chemical analytical methods that are traditionally undertaken using benchtop equipment in the laboratory environment. When applied to environmental monitoring, these "lab-on-chip" systems could allow high-performance chemical analysis methods to be performed in situ over distributed sensor networks with large numbers of measurement nodes. Here we present the first of a new generation of microfluidic chemical analysis systems with sufficient analytical performance and robustness for deployment in natural waters.

Evanescent photosynthesis: exciting cyanobacteria in a surface-confined light field.

The conversion of solar energy to chemical energy useful for maintaining cellular function in photosynthetic algae and cyanobacteria relies critically on light delivery to the microorganisms. Conventional direct irradiation of a bulk suspension leads to non-uniform light distribution within a strongly absorbing culture, and related inefficiencies. The study of small colonies of cells in controlled microenvironments would benefit from control over wavelength, intensity, and location of light energy on the scale of the microorganism.

Nanomolar detection with high sensitivity microfluidic absorption cells manufactured in tinted PMMA for chemical analysis.

We describe a novel, cost effective and simple technique for the manufacture of high sensitivity absorption cells for microfluidic analytical systems. The cells are made from tinted polymethyl methacrylate (PMMA) in which microfluidic channels are fabricated. Two windows (typically 250 μm thick, resulting in little optical power loss) are formed at either end of the channel through which light is coupled.

An integrated microfluidic chip for chromosome enumeration using fluorescence in situ hybridization.

Fluorescence in situ hybridization (FISH) is a powerful technique for probing the genetic content of individual cells at the chromosomal scale. Conventional FISH techniques provide a sensitive diagnostic tool for the detection of chromosomal alterations on a cell-by-cell basis; however, the cost-per-test in terms of reagent and highly qualified labour has prevented its wide-spread utilization in clinical settings. Here, we address the inefficient use of labour with the first integrated and automated on-chip FISH implementation, one that requires only minutes of setup time from the technician.

Rapid on-chip postcolumn labeling and high-resolution separations of DNA.

When performing genetic analysis on microfluidic systems, labeling the sample DNA for detection is a critical preparation step. Labeling procedures often involve fluorescently tagged primers and PCRs, which lengthen experimental run times and introduce higher levels of complexity, increasing the overall cost per analysis. Alternatively, on-chip labeling techniques based on intercalating dyes permit rapid labeling of DNA fragments.