Clinicopathological Analysis of Oral Paracoccidioidomycosis in Women.

Unlabelled: Paracoccidioidomycosis (PCM) is a deep systemic mycosis caused by Paracoccidioides brasiliensis. PCM affects predominantly men in their fifth and sixth decades of life, with low prevalence in women. The reasons for this discrepancy are not fully understood, but oestrogen may influence the transformation of the fungus and modulate the immune response.

Effect of high irradiance and short exposure times on the depth of cure of six bulk-fill resin composites.

This study examined the effect of high irradiance and short exposure times on the depth of cure of six resin-based composites (RBCs). Bluephase PowerCure and the Valo X light-curing units (LCUs) were used to photocure bulk-fill RBCs for their recommended exposure times: Admira Fusion x-tra (AFX/20s), Aura Bulk Fill (ABF/20s), Filtek One Bulk Fill (FOB/20s), Opus Bulk Fill APS (OBF/30s), Tetric EvoCeram Bulk Fill (TEC/10s) and Tetric PowerFill (TPF/10s). In addition, all bulk-fill RBCs were tested for depth of cure with one short 3 s exposure time from the Bluephase PowerCure or the Valo X in the Xtra Power mode.

Ultraviolet C as a method of disinfecting medical silicone used in facial prostheses: An in vitro study - Part 2.

Statement Of Problem: Disinfection is an important factor in preserving facial prostheses and maintaining tissue health. However, whether disinfection with ultraviolet C is an effective disinfection method is unclear.

Purpose: The purpose of this in vitro study was to evaluate the effectiveness of irradiation with different exposure durations of an ultraviolet-C light-emitting diode in the disinfection of the silicone (A-588-1; Factor II) used in facial prostheses.

Epidemiology and severity of traumatic dental injuries in permanent teeth: A 20-year retrospective study.

This study aimed to assess the traumatic dental injuries (TDIs) in permanent dentition among patients who attended at the outpatient clinic of a Brazilian dental school, during the last 20 years, and to investigate factors associated with the severity of these injuries. Clinical records of patients who attended a specialized center for dental trauma care in Brazil presenting at least one TDI in a permanent tooth, between the years 2000 and 2019, were reviewed. The data recorded were sex, age, affected arch, etiology, number, and type of the teeth affected, and classification and severity of the TDIs.

Factors associated with the proportion of abnormal results in screening mammograms: ecological study.

Objective: To analyze the factors associated with the proportion of abnormal results in screening mammograms.

Methods: Ecological study, with data from DATASUS/SISCAN, Atlas Brasil do Desenvolvimento Humano, Fundação SEADE, and Sistema e-Gestor, from 2016 to 2019, of women aged 50 to 69 years in the 645 municipalities of São Paulo (Brazil). Independent variables were associated with the outcome: proportion of unsatisfactory coverage of abnormal test results (Breast Imaging Reporting and Data System - BI-RADS® 0, 4 and 5 proportion >10% of tests performed).

Interaction of different concentrations of 10-MDP and GPDM on the zirconia bonding.

Objectives: To analyze the influence of different concentrations of 10-MDP and GPDM used, combined or not, on the bonding to zirconia.

Methods: Specimens of zirconia and a resin-composite (7 mm length, 1 mm width, and 1 mm thick) were obtained. The experimental groups were obtained according to the functional monomer (10-MDP and GPDM) and the concentrations (3 %, 5 %, and 8 %).

Influence of alveolar bone height on the biomechanical behavior of roots restored with custom-made posts-and-cores.

Objetive: This study evaluated the influence of alveolar bone height and post type on compressive force resistance, fracture pattern, and stress distribution in endodontically treated teeth.

Materials And Methods: Bovine roots were endodontically treated and divided into eight groups (n = 10) according to alveolar bone height (normal alveolar bone and alveolar bone loss - 2 and 5 mm from the margin of the crown, respectively) and post type (prefabricated glass fiber post, anatomic glass fiber post, customized milled glass fiber post-and-core and customized milled polyetheretherketone (PEEK) post-and-core). Mechanical fatigue was simulated (300.

Effects of gastric acid and mechanical toothbrushing in CAD-CAM restorative materials: Mechanical properties, surface topography, and biofilm adhesion.

Objective: To evaluate the effects of simulated gastric acid erosion combined with mechanical toothbrushing abrasion on the mechanical properties, surface topography, and biofilm adhesion of different CAD/CAM materials.

Material And Methods: Specimens of zirconia-reinforced lithium silicate glass-ceramic (ZLS), polymer-infiltrated ceramic network (PICN), feldspathic glass-ceramic (FE), and two nanoceramic resins (RK, RG), were submitted to the following challenges: erosion (E), abrasion (A), erosion combined with abrasion (E + A), or remained untreated (control - C). After challenges, flexural strength was evaluated, while microhardness (KHN) and surface roughness (Ra) were tested before and after treatments.

Biomechanical behavior of weakened roots restored with custom-made post-and-cores of glass fiber and polyetheretherketone.

Purpose: To evaluate the influence of post type and mechanical aging on compression force resistance, fracture pattern, and stress distribution in weakened roots.

Materials And Methods: Bovine roots were endodontically treated and widened-and randomly divided into 8 groups (n = 10) according to post type (prefabricated glass fiber post and customized anatomic glass fiber post, milled glass fiber post-and-core, and milled polyetheretherketone post-and-core) and mechanical aging (without and with mechanical aging). Three hundred thousand cycles of mechanical fatigue were performed and compression force resistance (N) was analyzed by two-way ANOVA and Tukey test (α = 0.

Impact of neuroinflammation on epigenetic transcriptional control of Sonic Hedgehog members in the central nervous system.

Sonic Hedgehog (Shh) signaling plays a critical role during central nervous system (CNS) development, and its dysregulation leads to neurological disorders. Nevertheless, little is known about Shh signaling regulation in the adult brain. Here, we investigated the contribution of DNA methylation on the transcriptional control of Shh signaling pathway members and its basal distribution impact on the brain, as well as its modulation by inflammation.

Comparative Evaluation of Bulk-Fill Composite Resins: Knoop Microhardness, Diametral Tensile Strength and Degree of Conversion.

Purpose: Bulk-fill composite resins were developed to reduce time and facilitate the restorative procedure. However, considering their recent introduction on the market and the new formulations, their performance still requires evaluation. This study aimed to evaluate Knoop microhardness (KHN), diametral tensile strength (DTS) and degree of conversion (DC) of three Bulk-Fill composite resins and a conventional one.

PEEK and fiberglass intra-radicular posts: influence of resin cement and mechanical cycling on push-out bond strength.

Objectives: To evaluate the bond strength of four types of posts (pre-fabricated fiberglass post, fiberglass post anatomized with composite resin, milled fiberglass post, and milled polyetheretherketone (PEEK) post), and two types of resin cements (conventional and self-adhesive) by assessing immediate bond strength and post-mechanical aging at each root third.

Materials And Methods: Bovine endodontically treated roots (16 groups, n = 8) were prepared and the posts were produced and luted; the specimens of aging groups were cycled (300,000 cycles under 50 N load at 1.2 Hz frequency); six slices of each root were obtained; push-out test was performed by using a universal testing machine (500 N load at 1 mm/min cross speed); fracture pattern was classified into five levels.

TiO2 nanotube-containing glass ionomer cements display reduced aluminum release rates.

Titanium dioxide nanotubes (TiO2-nts) were incorporated into a glass ionomer cement (GIC) with improved mechanical properties and antibacterial activity. The aims of the present in vitro study were to define the elemental characterization, aluminum (Al) release rate, and initial working time for GIC reinforced with TiO2-nts, in an experimental caries model. TiO2-nts were incorporated into GIC powder components at 5% by weight, and compared with unblended GIC.

Influence of Adhesion Promoter Primers on Polymerization Kinetics and Long-term Bond Strength of Composite Cements to Zirconia.

Purpose: To investigate the influence of primers on polymerization kinetics of resin-based luting and its effect on the microhardness and bond strength to zirconia. Materials and Methods: Panavia V5 (PV; Kuraray Noritake) with Tooth Primer (TPprimer; Kuraray Noritake) or Clearfil Ceramic Primer (CPprimer; Kuraray Noritake), and RelyX Ultimate (RU; 3M Oral Care) with Scotchbond Universal (SUadhesive; 3M Oral Care) were evaluated. Polymerization kinetics of luting materials with or without primers (TPprimer or SUadhesive) were evaluated using Fourier transform near-infrared (FT-NIR) spectroscopy in self- and dual-curing modes (n = 5).

Chemomechanical preparation influences the microbial community and the levels of LPS, LTA and cytokines in combined endodontic-periodontal lesions: A clinical study.

Background: This study was conducted to compare the microbiomes, the levels of lipopolysaccharides (LPS), lipoteichoic acid (LTA), and cytokines (interleukin [IL]-1β and tumor necrosis factor-alpha [TNF-α]), before and after chemomechanical preparation (CMP) of the root canals (RC) and their associated periodontal pockets (PP) in teeth with combined EPL.

Materials: Samples were taken from 10 RC and PP, before and after CMP. The microbiomes (next-generation sequencing, V3-V4 hypervariable region of the 16S rRNA gene), microbiome diversity (bioinformatics analyses), LPS (limulus amebocyte lysate), LTA, IL-1β, and TNF-α (ELISA) were evaluated.

Prevalence of dental trauma in Brazilian children and adolescents: a systematic review and meta-analysis.

This study aimed to investigate the prevalence of dental trauma in Brazilian children and adolescents. A systematic review was conducted considering eight databases: MEDLINE (via PubMed), LILACS, BBO, Scopus, Embase, Web of Science, Open Access Theses and Dissertations, and OpenThesis. Only prevalence studies that used a probabilistic sampling method were included, without restriction on year or language of publication.

Antibacterial efficacy of non-thermal atmospheric plasma against Streptococcus mutans biofilm grown on the surfaces of restorative resin composites.

The aim of this study was to evaluate the antimicrobial efficacy of non-thermal atmospheric plasma (NTAP) against Streptococcus mutans biofilms. Resin discs were fabricated, wet-polished, UV sterilized, and immersed in water for monomer extraction (37 °C, 24 h). Biofilms of bioluminescent S.

The association of inadequate lip coverage and malocclusion with dental trauma in Brazilian children and adolescents - A systematic review and meta-analysis.

Background/aim: Dental trauma (DT) occurs frequently in children and adolescents. Therefore, understanding the factors associated with its occurrence in these age groups is important to establish specific preventive measures. The aim of this study was to investigate the relationships of lip coverage, overjet, and open bite to dental trauma in Brazilian children and adolescents.

Physicochemical properties of dental resins formulated with amine-free photoinitiation systems.

Objective: To assess the mechanical properties of two different dimethacrylate resin blends containing the photosensitizer camphorquinone (CQ) alone or in combination with one or more synergists including an amine and/or an iodonium.

Methods: Two co-monomer resin blends were formulated using Bis-GMA/TEGDMA and UDMA/TEGDMA, both at 1:1 mass ratio. Each resin blend was divided into four groups, comprising the following four photoinitiation systems: (1) CQ + 2-(dimethylamino)ethyl methacrylate (DMAEMA); (2) CQ + DMAEMA + bis(4-methyl phenyl)iodonium hexafluorophosphate (BPI); (3) CQ; and (4) CQ + BPI.

Titanium dioxide nanotubes added to glass ionomer cements affect S. mutans viability and mechanisms of virulence.

This in vitro study evaluated the impact of TiO2 nanotubes (n-TiO2) incorporated into glass ionomer cement (GIC) on Streptococcus mutans (S. mutans) characteristics at cellular and molecular levels. n-TiO2, synthesized by the alkaline method (20 nm in size), was added to Ketac Molar EasyMix® at 0%, 3%, 5%, and 7% by weight.

Identification of Culturable and Nonculturable Microorganisms, Lipopolysaccharides, and Lipoteichoic Acids From Root Canals of Teeth With Endodontic Failure.

Aim: To elucidate the presence of apical periodontitis in the root canal of teeth with secondary/persistent infection, including composition of microbiota, levels of endotoxins and lipoteichoic acid (LTA), and clinical implications of these findings.

Method: Samples were collected from root canals of 50 patients who needed endodontic retreatment and had radiographic evidence of apical periodontitis. Microorganisms were identified by using the culture technique and biochemical tests.

DNMT1 Inhibitor Restores RUNX2 Expression and Mineralization in Periodontal Ligament Cells.

Periodontal ligament cells (PDLCs) have well documented osteogenic potential; however, this commitment can be highly heterogenous, limiting their applications in tissue regeneration. In this study, we use PDLC populations characterized by high and low osteogenic potential (h-PDLCs and l-PDLCs, respectively) to identify possible sources of such heterogeneity and to investigate whether the osteogenic differentiation can be enhanced by epigenetic modulation. In h-PDLCs, low basal expression levels of pluripotency markers (, ), DNA methyltransferases (, ), and enzymes involved in active DNA demethylation (, ) were prerequisite to high osteogenic potential.

Flexural strength and microhardness of bulk-fill restorative materials.

Background: Bulk-fill materials can facilitate the restorative procedure mainly for deep and wide posterior cavities. The purpose of this study was to evaluate flexural strength (biaxial flexural strength [BFS]) and microhardness (Knoop microhardness [KHN]) at different depths of bulk-fill materials.

Methods: Five bulk-fill materials were tested: two light-curable composite resins, one dual-cure composite, one bioactive restorative, and a high-viscosity glass ionomer.

TiO nanotubes improve physico-mechanical properties of glass ionomer cement.

Objectives: The aim of this study was to determine the physico-mechanical properties of a high viscosity glass ionomer cement (GIC) reinforced with TiO nanotubes (TiO-nt).

Methods: TiO-nt was incorporated into the GIC powder components (Ketac Molar EasyMix™) in concentrations of 0% (control group), 3%, 5%, 7% by weight. Compressive strength (n = 10/group), three point bending for flexural strength (n = 18/group), microshear bond strength to dentin and failure mode (n = 20/group), and surface roughness and weight loss before and after brushing simulation (30,000 cycles) (n = 8/group) were evaluated.

Randomized clinical trial of four adhesion strategies: A 42 month study.

Context: The adhesives clinical effectiveness has been extensively reported for noncarious cervical lesions (NCCLs). However, there is a lack of information about the adhesive systems strategies and their effect on NCCL restoration longevity.

Aims: This study aims to evaluate a 42-month performance of four dentin adhesive systems used for the restorative treatment of NCCLs.