Life Cycle Assessment of Rare Earth Elements-Free Permanent Magnet Alternatives: Sintered Ferrite and Mn-Al-C.

Permanent magnets are fundamental constituents in key sectors such as energy and transport, but also robotics, automatization, medicine, etc. High-performance magnets are based on rare earth elements (RE), included in the European list of critical raw materials list. The volatility of their market increased the research over the past decade to develop RE-free magnets to fill the large performance/cost gap existing between ferrites and RE-based magnets.

A review of the existing and emerging technologies for wastewaters containing tetramethyl ammonium hydroxide (TMAH) and waste management systems in micro-chip microelectronic industries.

The present work aims to describe and review the available technologies and the recent advancements in treating industrial wastewater containing tetramethylammonium hydroxide (TMAH). It is a quaternary ammonium salt and widely used in the microelectronics industry; this kind of company produces large quantities of wastewater containing TMAH. The exhausted solutions must be treated appropriately since TMAH is corrosive, toxic to human health, and ecotoxic.

Technical feasibility of biodiesel production from virgin oil and waste cooking oil: Comparison between traditional and innovative process based on hydrodynamic cavitation.

Biodiesel production calls for innovative solutions to turn into a competitive process with a reduced environmental impact. One of the process bottlenecks stands in the immiscibility of oil and alcohol as raw materials, so mixing process largely impacts the overall process cost. This process step, if carried out by using hydrodynamic cavitation, has the possibility to become a benchmark for large scale applications.

Purification of residual leach liquors from hydrometallurgical process of NiMH spent batteries through micellar enhanced ultra filtration.

Hydrometallurgical processes for the treatment and recovery of metals from waste electrical and electronic equipment produce wastewaters containing heavy metals. These residual solutions cannot be discharged into the sewer without an appropriate treatment. Specific wastewater treatments integrated with the hydrometallurgical processes ensure a sustainable recycling loops of the electrical wastes to maximize the metals recovery and minimize the amount of wastes and wastewaters produced.

Treatment of WEEE industrial wastewaters: Removal of yttrium and zinc by means of micellar enhanced ultra filtration.

In this paper, the efficiency of micellar enhanced ultrafiltration technique (MEUF) was tested for the removal of yttrium and zinc ions from synthetic industrial liquid wastes. UF membranes (monotubular ceramic membranes of 210 kDa and 1 kDa molecular weight cut-off) were used with adding an anionic surfactant, sodium dodecyl sulfate (SDS). A two - level full factorial design was performed in order to evaluate the effect of molecular weight cut-off, sodium dodecyl sulfate concentration and pressure on the permeate flux and rejection yields.

A hydrometallurgical process for the recovery of terbium from fluorescent lamps: Experimental design, optimization of acid leaching process and process analysis.

Terbium and rare earths recovery from fluorescent powders of exhausted lamps by acid leaching with hydrochloric acid was the objective of this study. In order to investigate the factors affecting leaching a series of experiments was performed in according to a full factorial plan with four variables and two levels (4). The factors studied were temperature, concentration of acid, pulp density and leaching time.

Yttrium recovery from primary and secondary sources: a review of main hydrometallurgical processes.

Yttrium is important rare earths (REs) used in numerous fields, mainly in the phosphor powders for low-energy lighting. The uses of these elements, especially for high-tech products are increased in recent years and combined with the scarcity of the resources and the environmental impact of the technologies to extract them from ores make the recycling waste, that contain Y and other RE, a priority. The present review summarized the main hydrometallurgical technologies to extract Y from ores, contaminated solutions, WEEE and generic wastes.

Recovery of yttrium from fluorescent powder of cathode ray tube, CRT: Zn removal by sulphide precipitation.

This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2(2) full factorial plan and the highest extraction yields for yttrium and zinc equal to 100% are observed under the following conditions: 3M of sulphuric acid, 10% v/v of H2O2 concentrated solution at 30% v/v, 10% w/w pulp density, 70°C and 3h of reaction.