Assessing the Long-Term Performance of Adhesive Joints in Space Structures during Interplanetary Exploration.

Spacecraft experience minimal mechanical loads in space, but with the development of reusable spacecraft for interplanetary exploration and repeated landings, structures will be subjected to increased mechanical stress. The impact of the space environment on the aging of adhesive materials used in space structures over long-term applications is not well understood. This study investigates two commonly used adhesives in spacecraft assembly, namely Scotch-Weld™ EC-2216 and Scotch-Weld™ EC-9323-2, under two aging conditions: (1) high-energy electron irradiation using a Van de Graaf accelerator, and (2) thermal vacuum cycling.

Development of Sustainable High Performance Epoxy Thermosets for Aerospace and Space Applications.

There is an imperative need to find sustainable ways to produce bisphenol A free, high performance thermosets for specific applications such as the space or aerospace areas. In this study, an aromatic tris epoxide, the tris(4-hydroxyphenyl)methane triglycidyl ether (THPMTGE), was selected to generate high crosslinked networks by its copolymerization with anhydrides. Indeed, the prepared thermosets show a gel content () ~99.

Surface-enhanced Raman scattering sensors for biomedical and molecular detection applications in space.

Unlabelled: The detection of molecular traces in the environment is a technical problem that is critical in pollutant control procedures at all stages of spacecraft assembly, in space flight, as well as in other technological processes such as food production, medical diagnostics, environmental control, warfare. However, in the aerospace industry, it is necessary to detect molecular traces of contaminants with extreme sensitivity, as even concentrations as low as part-per-billion (ppb) can be critical during long missions. The high sensitivity of the Volatile Organic Compounds (VOCs) detection within the air can be a challenge because of the poor affinity of VOC's to the metal surface of the sensor substrate.

Optimisation of Through-Thickness Embedding Location of Fibre Bragg Grating Sensor in CFRP for Impact Damage Detection.

Aerospace composites are susceptible to barely visible impact damage (BVID) produced by low-velocity-impact (LVI) events. Fibre Bragg grating (FBG) sensors can detect BVID, but often FBG sensors are embedded in the mid-plan, where residual strains produced by impact damage are lower, leading to an undervaluation of the damage severity. This study compares the residual strains produced by LVI events measured by FBG embedded at the mid-plan and other through-thickness locations of carbon fibre reinforced polymer (CFRP) composites.

Fused Filament Fabrication of PEEK: A Review of Process-Structure-Property Relationships.

Poly (ether ether ketone) (PEEK) is a high-performance engineering thermoplastic polymer with potential for use in a variety of metal replacement applications due to its high strength to weight ratio. This combination of properties makes it an ideal material for use in the production of bespoke replacement parts for out-of-earth manufacturing purposes, in particular on the International Space Station (ISS). Additive manufacturing (AM) may be employed for the production of these parts, as it has enabled new fabrication pathways for articles with complex design considerations.

Strong graphene oxide nanocomposites from aqueous hybrid liquid crystals.

Combining polymers with small amounts of stiff carbon-based nanofillers such as graphene or graphene oxide is expected to yield low-density nanocomposites with exceptional mechanical properties. However, such nanocomposites have remained elusive because of incompatibilities between fillers and polymers that are further compounded by processing difficulties. Here we report a water-based process to obtain highly reinforced nanocomposite films by simple mixing of two liquid crystalline solutions: a colloidal nematic phase comprised of graphene oxide platelets and a nematic phase formed by a rod-like high-performance aramid.

Electrically Conductive Polyetheretherketone Nanocomposite Filaments: From Production to Fused Deposition Modeling.

The present work reports the production and characterization of polyetheretherketone (PEEK) nanocomposite filaments incorporating carbon nanotubes (CNT) and graphite nanoplates (GnP), electrically conductive and suitable for fused deposition modeling (FDM) processing. The nanocomposites were manufactured by melt mixing and those presenting electrical conductivity near 10 S/m were selected for the production of filaments for FDM. The extruded filaments were characterized for mechanical and thermal conductivity, polymer crystallinity, thermal relaxation, nanoparticle dispersion, thermoelectric effect, and coefficient of friction.

Reduced enthalpy of metal hydride formation for Mg-Ti nanocomposites produced by spark discharge generation.

Spark discharge generation was used to synthesize Mg-Ti nanocomposites consisting primarily of a metastable body-centered-cubic (bcc) alloy of Mg and Ti. The bcc Mg-Ti alloy transformed upon hydrogenation into the face-centered-cubic fluorite Mg1-yTiyHx phase with favorable hydrogen storage properties. Both metal and metal hydride nanocomposites showed a fractal-like porous morphology, with a primary particle size of 10-20 nm.

Uniform metal nanoparticles produced at high yield in dense microemulsions.

This article demonstrates that bicontinuous microemulsions are optimal templates for high yield production of metal nanoparticles. We have verified this for a variety of microemulsion systems having AOT (sodium bis (2-ethyhexyl) sulphosuccinate) or a fluorocarbon (perfluoro (4-methyl-3,6-dioxaoctane)sulphonate) as surfactant mixed with water and oils like n-heptane or n-dodecane. Several types of metal nanoparticles, including platinum, gold and iron, were produced in these microemulsions having a size range spanning 1.

Dynamic solubility limits in nanosized olivine LiFePO4.

Because of its stability, nanosized olivine LiFePO(4) opens the door toward high-power Li-ion battery technology for large-scale applications as required for plug-in hybrid vehicles. Here, we reveal that the thermodynamics of first-order phase transitions in nanoinsertion materials is distinctly different from bulk materials as demonstrated by the decreasing miscibility gap that appears to be strongly dependent on the overall composition in LiFePO(4). In contrast to our common thermodynamic knowledge, that dictates solubility limits to be independent of the overall composition, combined neutron and X-ray diffraction reveals strongly varying solubility limits below particle sizes of 35 nm.

Synthesis of magnetic noble metal (nano)particles.

Noble metal particles can be made strongly ferromagnetic or diamagnetic provided that they are synthesized in a sufficiently strong magnetic field. Here we outline two synthesis methods that are fast, reproducible, and allow broad control over particle sizes ranging from nanometers to millimeters. From magnetometry and light spectroscopy, it appears that the cause of this anomalous magnetism is the surface anisotropy in the noble metal particles induced by the applied magnetic field.

An aerosol-based route to nanostructured powders synthesis in liquids.

An alternative technique for synthesizing nanostructured powders in liquid solutions has been developed. The technique combines generation of charged aerosols via electrospray with reductive precipitation reactions in liquids. Electrospray of liquids is carried out to produce micrometric, nearly mono-dispersed airborne droplets from a precursor solution.

Assembly of colloidal semiconductor nanorods in solution by depletion attraction.

Arranging anisotropic nanoparticles into ordered assemblies remains a challenging quest requiring innovative and ingenuous approaches. The variety of interactions present in colloidal solutions of nonspherical inorganic nanocrystals can be exploited for this purpose. By tuning depletion attraction forces between hydrophobic colloidal nanorods of semiconductors, dispersed in an organic solvent, these could be assembled into 2D monolayers of close-packed hexagonally ordered arrays directly in solution.

Synthesis of nanoparticles of Cu, Sb, Sn, SnSb and Cu2Sb by densification and atomization process.

Here we present a technique based on an initial densification of solid precursor materials using magnetic pulses followed by an atomization process via spark discharging. These two processes allow changing bulky micron sized materials into nanoparticles (5-60 nm). The resulting intermediates and nanomaterials have been characterized using electron microscopy (TEM, SEM) and X-ray diffraction to show the texture and structure evolution between the initial bulk phase and the final nanoparticles.