Analysis of Mechanical and Thermal Properties of Polymer Materials Derived from Recycled Overprinted Metallized PP Films.

Polymer materials and their composites are one of the most frequently used materials in the packaging and food industries. This applies to both disposable and reusable packaging, layered films with barrier properties, as well as densely overprinted polymer films and metallized food wrap films. According to statistical data from Plastics Europe, approximately 40% of processed thermoplastics are used to produce packaging, including single- and multi-layer film packaging.

Analysis of Selected Properties of Polymer Mixtures Derived from Virgin and Re-Granulated PP with Glass Fibers.

The problem of the growing amount of waste polymer materials currently affects virtually every area of the global economy. New actions taken by the E.U.

Comparison of Physical and Thermal Properties of Mulching Films Made of Different Polymeric Materials.

The development of polymer materials causes their huge expansion into various areas of everyday life, as well as plant and animal production. Their chemical resistance, good physical properties, and ease of processing result in an increasing use of this group of materials. Outdoor plant production both in open plantations and greenhouses requires various types of materials supporting the vegetation process as well as protecting against pests and weeds.

Performance of Biodegradable Biochar-Added and Bio-Based Plastic Clips for Growing Tomatoes.

Increasing quantities of waste from using conventional plastic in agriculture and horticulture is one of the most pressing issues nowadays. Conventional plastic accessories (e.g.

End-of-Life Management of Biodegradable Plastic Dog Poop Bags through Composting of Green Waste.

Plastic waste derived from plastic dog poop bags (DPBs) could be considered a negligible source of plastic waste. However, it is estimated that this kind of waste contributes to 0.6% of the total plastic waste generated worldwide, and it is expected to increase in the following years.

The Analysis of Polyethylene Hip Joint Endoprostheses Strength Parameters Changes after Use inside the Human Body.

The influence of dynamic loads resulting from human motor activity and electrocorrosion inside the human body on the strength parameters of artificial joint elements has not yet been investigated. Hip joint arthroplasty is the most common surgical procedure in the world that allows doctors to remove pain and restore motor skills in people with severe hip diseases, after accidents, and in the elderly. Based on the reports, this article assesses changes in the number of implanted endoprostheses in the years 2005-2019 and determines the trends and estimated changes in the number of implanted hip prostheses in the following decades.

Effect of Sago Starch Modifications on Polystyrene/Thermoplastic Starch Blends.

The preparation of polystyrene/thermoplastic starch (PS/TPS) blends was divided into three stages. The first stage involved the preparation of TPS from sago starch. Then, for the second stage, PS was blended with TPS to produce a TPS/PS blend.

Elevated-Temperature Performance, Combustibility and Fire Propagation Index of Fly Ash-Metakaolin Blend Geopolymers with Addition of Monoaluminium Phosphate (MAP) and Aluminum Dihydrogen Triphosphate (ATP).

Thermal performance, combustibility, and fire propagation of fly ash-metakaolin (FA-MK) blended geopolymer with the addition of aluminum triphosphate, ATP (Al(HPO)), and monoaluminium phosphate, MAP (AlPO) were evaluated in this paper. To prepare the geopolymer mix, fly ash and metakaolin with a ratio of 1:1 were added with ATP and MAP in a range of 0-3% by weight. The fire/heat resistance was evaluated by comparing the residual compressive strengths after the elevated temperature exposure.

Tool Wear and Surface Evaluation in Drilling Fly Ash Geopolymer Using HSS, HSS-Co, and HSS-TiN Cutting Tools.

This paper reports on the potential use of geopolymer in the drilling process, with respect to tool wear and surface roughness. The objectives of this research are to analyze the tool life of three different economy-grade drill bit uncoated; high-speed steel (HSS), HSS coated with TiN (HSS-TiN), and HSS-cobalt (HSS-Co) in the drilling of geopolymer and to investigate the effect of spindle speed towards the tool life and surface roughness. It was found that, based on the range of parameters set in this experiment, the spindle speed is directly proportional to the tool wear and inversely proportional to surface roughness.

Image Analysis of Surface Porosity Mortar Containing Processed Spent Bleaching Earth.

Image analysis techniques are gaining popularity in the studies of civil engineering materials. However, the current established image analysis methods often require advanced machinery and strict image acquisition procedures which may be challenging in actual construction practices. In this study, we develop a simplified image analysis technique that uses images with only a digital camera and does not have a strict image acquisition regime.