Experimental demonstration of single-span 100-km O-band 4×50-Gb/s CWDM direct-detection transmission.

We report on what is to the best of our knowledge the longest 50-Gb/s/λ O-band wavelength-division multiplexed (WDM) transmission. A pair of in-house built bismuth-doped fiber amplifiers (BDFAs) and the use of Kramers-Kronig detection-assisted single-sideband transmission are adopted to overcome the fiber loss and chromatic dispersion, respectively, in a reach-extended O-band coarse WDM (CWDM) system with a channel spacing of ∼10 nm. Through experiments on an amplified 4×50-Gb/s/λ direct-detection system based on booster and pre-amp BDFAs, we show the superior performance of single-sideband transmission in terms of both optical signal-to-noise ratio sensitivity and uniformity in performance amongst CWDM channels relative to double-sideband transmission after both 75-km and 100-km lengths of single-mode fiber.

Numerical and experimental study on the impact of chromatic dispersion on O-band direct-detection transmission.

The recent emergence of efficient O-band amplification technologies has enabled the consideration of O-band transmission beyond short reach. Despite the O-band being a low chromatic dispersion (CD) window, the impact of CD will become increasingly significant when extending the reach of direct-detection (DD) systems. In this work, we first numerically investigate the 3-dB bandwidth of single-mode fibers (SMF) and the CD-restricted transmission reach in intensity-modulation DD systems, confirming the significant difference between low- and high-dispersion O-band wavelengths.

Experimental characterization of an o-band bismuth-doped fiber amplifier.

The recent emergence of bismuth-doped fiber amplifiers (BDFAs) offers the potential to transmit high-speed WDM signals over long distances in the O-band spectral region, thereby greatly enhancing the scope of systems utilizing these wavelengths. In this paper, we present a comprehensive experimental study on several basic characteristics of an O-band BDFA based on a phosphosilicate optical fiber, including the frequency-dependent noise figure, gain tilt (static and dynamic), transient response, and polarization dependent gain. We discuss our findings and their implications on the use of BDFA technology in high bit-rate multichannel systems.

Study on the temperature dependent characteristics of O-band bismuth-doped fiber amplifier.

We report the temperature dependent performance of an O-band bismuth (Bi)-doped fiber amplifier (BDFA) in the temperature range from -60 to +80°C. At room temperature, maximum gains of 27 and 40 dB with noise figures (NFs) of 4.3 and 4.

40 dB gain all fiber bismuth-doped amplifier operating in the O-band.

In this Letter, we investigate and compare the gain and noise figure characteristics of bismuth (Bi)-doped fiber amplifiers configured in both single and double signal pass implementations. A maximum gain of 25 dB and a noise figure of 4 dB is measured at 1360 nm in the single pass configuration for -23  dBm input signal power, whereas in the double pass configuration the gain of the amplifier is improved significantly by 14 dB allowing us to achieve a gain of 39 dB with a noise figure of 5 dB. To the best of our knowledge, this is the highest gain reported to date using Bi-doped fiber as a gain medium.

Bismuth-doped all-fiber mode-locked laser operating at 1340 nm.

We demonstrate a 1340 nm mode-locked Bismuth (Bi)-doped fiber laser without any saturable absorber. The effect of pump power on pulse width is studied, and a variation from 1.5 to 3 ns is reported.

Bi-doped fiber amplifier with a flat gain of 25 dB operating in the wavelength band 1320-1360 nm.

Bismuth (Bi)-doped phosphosilicate fibers have been fabricated by the modified chemical vapor deposition (MCVD)-solution doping technique under different process conditions. The influence of fabrication conditions on unsaturable loss in fibers has been investigated. Pump wavelength dependent Bi gain has been studied to obtain a flat gain over a wide bandwidth.

1120 nm diode-pumped Bi-doped fiber amplifier.

Bismuth-doped aluminosilicate fiber has been fabricated by the MCVD-solution doping method and characterized for its unsaturable loss and gain. The amplifier performance has been compared for a novel pumping wavelength of 1120 nm with the conventional pumping wavelength region of 1047 nm. Unsaturable loss was 65% and 35% at 1047 and 1120 nm, pump wavelengths, respectively.