Microfluidics for High Pressure: Integration on GaAs Acoustic Biosensors with a Leakage-Free PDMS Based on Bonding Technology.

Microfluidics integration of acoustic biosensors is an actively developing field. Despite significant progress in "passive" microfluidic technology, integration with microacoustic devices is still in its research state. The major challenge is bonding polymers with monocrystalline piezoelectrics to seal microfluidic biosensors.

Regenerable ZnO/GaAs Bulk Acoustic Wave Biosensor for Detection of in "Complex" Biological Medium.

A regenerable bulk acoustic wave (BAW) biosensor is developed for the rapid, label-free and selective detection of in liquid media. The geometry of the biosensor consists of a GaAs membrane coated with a thin film of piezoelectric ZnO on its top surface. A pair of electrodes deposited on the ZnO film allows the generation of BAWs by lateral field excitation.

Topology Challenge for the Assessment of Living Cell Deposits with Shear Bulk Acoustic Biosensor.

Shear bulk acoustic type of resonant biosensors, such as the quartz crystal microbalance (QCM), give access to label-free in-liquid analysis of surface interactions. The general understanding of the sensing principles was inherited from past developments in biofilms measurements and applied to cells while keeping the same basic assumptions. Thus, the biosensor readouts are still quite often described using 'mass' related terminology.

Assessment of Shear-Dependent Kinetics of Primary Haemostasis With a Microfluidic Acoustic Biosensor.

Primary haemostasis is a complex dynamic process, which involves in-flow interactions between platelets and sub-endothelial matrix at the area of the damaged vessel wall. It results in a first haemostatic plug, which stops bleeding, before coagulation ensues and consolidates it. The diagnosis of primary haemostasis defect would benefit from evaluation of the whole sequence of mechanisms involved in platelet plug formation in flow.

Towards an Ultra Sensitive Hybrid Mass Sensor Based on Mode Localization without Resonance Tracking.

We present a mode localized mass sensor prototype based on a hybrid system excited at a fixed frequency slightly below the resonances. Indeed, we show, both theoretically and experimentally, that this condition yields higher sensitivities and similar sensitivity ranges than that of resonance peak tracking while being less time consuming than a classical open-loop configuration due to the absence of frequency sweep. The system is made of a quartz resonator and a hardware that includes a resonator and the coupling.

A Fluidic Interface with High Flow Uniformity for Reusable Large Area Resonant Biosensors.

Resonant biosensors are known for their high accuracy and high level of miniaturization. However, their fabrication costs prevent them from being used as disposable sensors and their effective commercial success will depend on their ability to be reused repeatedly. Accordingly, all the parts of the sensor in contact with the fluid need to tolerate the regenerative process which uses different chemicals (H₃PO₄, H₂SO₄ based baths) without degrading the characteristics of the sensor.

Formation Kinetics of Mixed Self-Assembled Monolayers of Alkanethiols on GaAs(100).

We report on the formation kinetics of mixed self-assembled monolayers (SAMs) comprising 16-mercaptohexadecanoic acid (MHDA) and 11-mercapto-1-undecanol (MUDO) thiols on GaAs(100) substrates. These compounds were selected for their potential in constructing highly selective and efficient architectures for biosensing applications. The molecular composition and quality of one-compound and mixed SAMs were determined by the Fourier transform infrared absorption spectroscopy measurements.

Regeneration of a thiolated and antibody functionalized GaAs (001) surface using wet chemical processes.

Wet chemical processes were investigated to remove alkanethiol self-assembled monolayers (SAMs) and regenerate GaAs (001) samples studied in the context of the development of reusable devices for biosensing applications. The authors focused on 16-mercaptohexadecanoic acid (MHDA) SAMs that are commonly used to produce an interface between antibodies or others proteins and metallic or semiconductor substrates. As determined by Fourier transform infrared absorption spectroscopy, among the investigated solutions of HCl, H2O2, and NH4OH, the highest efficiency in removing alkanethiol SAM from GaAs was shown by NH4OH:H2O2 (3:1 volume ratio) diluted in H2O.

GaAs coupled micro resonators with enhanced sensitive mass detection.

This work demonstrates the improvement of mass detection sensitivity and time response using a simple sensor structure. Indeed, complicated technological processes leading to very brittle sensing structures are often required to reach high sensitivity when we want to detect specific molecules in biological fields. These developments constitute an obstacle to the early diagnosis of diseases.

Influence of a Thiolate Chemical Layer on GaAs (100) Biofunctionalization: An Original Approach Coupling Atomic Force Microscopy and Mass Spectrometry Methods.

Widely used in microelectronics and optoelectronics; Gallium Arsenide (GaAs) is a III-V crystal with several interesting properties for microsystem and biosensor applications. Among these; its piezoelectric properties and the ability to directly biofunctionalize the bare surface, offer an opportunity to combine a highly sensitive transducer with a specific bio-interface; which are the two essential parts of a biosensor. To optimize the biorecognition part; it is necessary to control protein coverage and the binding affinity of the protein layer on the GaAs surface.

Micro structuration of gaas surface by wet etching: towards a specific surface behavior.

Resonant microelectromechanical systems are promising devices for real time and highly sensitive measurements. The sensitivity of such sensors to additional mass loadings which can be increased thanks to the miniaturisation of devices is of prime importance for biological applications. The miniaturisation of structures passes through a photolithographic process and wet chemical etching.

Langasite as a piezoelectric material for near-field microscopy resonant cantilevers.

Quartz length-extension resonators have already been used to obtain atomically-resolved images by frequency-modulation atomic force microscopy. Other piezoelectric materials such as gallium orthophosphate (GaPO(4)), langatate (LGT), and langasite (LGS) could be appropriate for this application. In this paper, the advantages of langasite crystal are presented and the fabrication of similar microsensors in langasite temperature-compensated cuts by chemical etching is proved.