Unraveling the Mechanism and Practical Implications of the Sol-Gel Synthesis of Spinel LiMnO as a Cathode Material for Li-Ion Batteries: Critical Effects of Cation Distribution at the Matrix Level.

Spinel LiMnO (LMO) is a state-of-the-art cathode material for Li-ion batteries. However, the operating voltage and battery life of spinel LMO needs to be improved for application in various modern technologies. Modifying the composition of the spinel LMO material alters its electronic structure, thereby increasing its operating voltage.

Comparison of Two pMDIs in Adult Asthmatics: A Randomized Double-Blind Double-Dummy Clinical Trial.

Background: Only a few studies directly compared the therapeutic efficacy and safety of two pressurized metered-dose inhalers (pMDIs) in asthma. We analyzed the asthma treatment outcomes, safety, and patient preferences using formoterol/beclomethasone (FORM/BDP), a pMDI with extra-fine particles, compared with formoterol/budesonide (FORM/BUD), another pMDI with non-extra-fine particles.

Methods: In this randomized, double-blind, double-dummy parallel group study, 40 adult asthmatics were randomized to FORM/BDP group (n=18; active FORM/BDP and placebo FORM/BUD) or FORM/BUD group (n=22; active FORM/BUD and placebo FORM/BDP).

Free-Standing NiS₂ Electrode as High-Rate Anode Material for Sodium-Ion Batteries.

Owing to the speculated price hike and scarcity of lithium resources, sodium-ion batteries are attracting significant research interest these days. However, sodium-ion battery anodes do not deliver good electrochemical performance, particularly rate performance. Herein, we report the facile electrospinning synthesis of a free-standing nickel disulfide (NiS²) embedded on carbon nanofiber.

The Effect of Crystal Structure on the Growth of Nanotubular Oxide Layers Formed on Ti-Ni Alloys.

Electrochemical anodization of Ti-Ni alloys with different Ni composition was carried out in an ethylene glycol base electrolyte under the various conditions to investigate the effect of crystal structure and chemical composition of the Ti-Ni alloy. X-ray diffraction patterns indicated that Ti-48.0 Ni and Ti-49.

Effect of Thermal Cycling on Transformation Behavior of Ti-24Nb-1Mo Alloy (at.%).

The effect of thermal cycling on the transformation behavior of a Ti-24Nb-1Mo alloy was investigated by means of electrical resistivity measurement, transmission electron microscopy (TEM), X-ray diffraction (XRD), tensile test and Vickers hardness tests. Electrical resistivity changes were not observed in all alloys. It indicates that thermally induced martensitic transformation does not take place in the alloys.

Objective assessment of flap volume changes and aesthetic results after adjuvant radiation therapy in patients undergoing immediate autologous breast reconstruction.

Background: The use of immediate breast reconstruction and adjuvant radiation therapy is increasing in breast cancer patients. This study aimed to analyze the aesthetic outcome and changes in flap volume in patients with breast cancer undergoing radiation therapy of the surgical site after immediate autologous tissue reconstruction.

Methods: Immediate abdominal free flap breast reconstruction following unilateral mastectomy was performed in 42 patients; 21 patients received adjuvant radiation (study group) and 21 patients did not (control group).

Crystallization and Martensitic Transformation Behavior of Ti-Ni-Si Alloy Ribbons Prepared via Melt Spinning.

Ti-(50-x)Ni-xSi (at%) (x = 0.5, 1.0, 3.

Solidification Rate Dependence of Microstructures and Transformation Behavior of Ti-Ni-Hf Alloys.

The microstructures and transformation behavior of Ti-49Ni-20Hf, Ti-49.5Ni-20Hf and Ti-50.3Ni- 20Hf alloys, when prepared by conventional casting, were investigated and compared with the properties of the alloys prepared by melt spinning.

Investigating Self-Centering Capacity of Superelastic Shape Memory Alloy Fibers with Different Anchorages Through Pullout Tests.

This study investigated the pull-out resistance of superelastic shape memory alloy (SMA) short fibers in mortar with consideration of various end-anchorages that provide different anchoring actions. For the purpose, four types of SMA fibers were prepared using NiTi SMA wires with a diameter of 1.0 mm and the following four end shapes: straight (ST), L-shaped (LS), N-shaped (NS), and spearhead-shaped (SH).

Experiments on deformation behaviour of functionally graded NiTi structures.

Functionally graded NiTi structures benefit from the combination of the smart properties of NiTi and those of functionally graded structures. This article provides experimental data for thermomechanical deformation behaviour of microstructurally graded, compositionally graded and geometrically graded NiTi alloy components, related to the research article entitled "Functionally graded shape memory alloys: design, fabrication and experimental evaluation" (Shariat et al., 2017) [1].

Long-term clinical study and multiscale analysis of in vivo biodegradation mechanism of Mg alloy.

There has been a tremendous amount of research in the past decade to optimize the mechanical properties and degradation behavior of the biodegradable Mg alloy for orthopedic implant. Despite the feasibility of degrading implant, the lack of fundamental understanding about biocompatibility and underlying bone formation mechanism is currently limiting the use in clinical applications. Herein, we report the result of long-term clinical study and systematic investigation of bone formation mechanism of the biodegradable Mg-5wt%Ca-1wt%Zn alloy implant through simultaneous observation of changes in element composition and crystallinity within degrading interface at hierarchical levels.

Electrochemical properties of Si film electrodes grown on current collectors with CuO nanostructures for thin-film microbatteries.

Si film electrodes were deposited onto Cu foil current collectors fabricated with well-formed CuO nanostructures. The structural and electrochemical properties of the Cu foils oxidized for 1, 3, and 6 h and of the Si film electrodes were investigated using field-emission scanning electron microscopy, X-ray diffraction (XRD), and charge/discharge tests. The morphologies and XRD profiles suggested that the oxidized Cu foils consisted of a top CuO layer and a bottom Cu2O layer.

Compositionally graded Ti-Ni alloys prepared by diffusion bonding.

A Ti-Ni alloy compositionally graded along the thickness direction in order to obtain a shape change over a wide temperature range, which is beneficial to the actuator for precise position control, was prepared by spark plasma sintering (SPS) after stacking Ti-Ni alloy ribbons in the sequence of Ti-51Ni, Ti-50Ni, Ti-49Ni and Ti-48Ni (at%) followed by annealing. Then, the microstructure and martensitic transformation behavior were investigated by using FE-SEM, DSC and thermal cycling tests under a constant load. The inter-ribbon defects observed after SPS due to insufficient diffusional bonding between the ribbons were eliminated by post-SPS annealing at 1023 K for 36 ks.

Protection effect of ZrO2 coating layer on LiCoO2 thin film fabricated by DC magnetron sputtering.

Bare and ZrO2-coated LiCoO2 thin films were fabricated by direct current magnetron sputtering method on STS304 substrates. Deposited both films have a well-crystallized structure with (003) preferred orientation after annealing at 600 degrees C. The ZrO2-coated LiCoO2 thin film provide significantly improved cycling stability compared to bare LiCoO2 thin film at high cut-off potential (3.

Nullifying tumor efflux by prolonged endolysosome vesicles: development of low dose anticancer-carbon nanotube drug.

As the majority of side effects of current chemotherapies stems from toxicity due to excessive dosing of anticancer drugs, minimizing the amount of drug while maximizing drug efficacy is essential to increase the life-quality of chemotherapy patients. This study demonstrated that the intracellular delivery of amide linked doxorubicin on carbon nanotube can nullify the efflux of cancer cells by achieving prolonged endolysosome delivery and can induce burst release of doxorubicin in an acidic hydrolase environment and, ultimately, can reduce the amount of anticancer drug by 10-fold compared to conventional effective drug dose. The clearance of accumulated carbon nanotubes in the liver was observed after 4 weeks, and analysis of liver toxicity markers showed no significant changes in GOT and GPT levels and release of pro-inflammatory cytokines across both short- and long-term periods.

High performance enzyme fuel cells using a genetically expressed FAD-dependent glucose dehydrogenase α-subunit of Burkholderia cepacia immobilized in a carbon nanotube electrode for low glucose conditions.

FAD-dependent glucose dehydrogenase (FAD-GDH) of Burkholderia cepacia was successfully expressed in Escherichia coli and subsequently purified in order to use it as an anode catalyst for enzyme fuel cells. The purified enzyme has a low Km value (high affinity) towards glucose, which is 463.8 μM, up to 2-fold exponential range lower compared to glucose oxidase.

Influences of Ti film thickness on electrochemical properties of Si/Ti/Cu film electrodes.

Si and Si/Ti films were fabricated on a Cu current collector (substrate) using the DC sputtering system. The Ti film as a buffer layer was inserted between the Si film and the Cu current collector. Their structural and electrochemical properties were investigated with various Ti film thicknesses of 20-90 nm.

The effects of substrate and annealing on structural and electrochemical properties in LiCoO2 thin films prepared by DC magnetron sputtering.

LiCoO2 thin films were fabricated by direct current magnetron sputtering method on STS304 and Ti substrates. The effects of substrate and annealing on their structural and electrochemical properties of LiCoO2 thin film cathode were studied. Crystal structures and surface morphologies of the deposited films were investigated by X-ray diffraction and field emission scanning electron microscopy.

Role of subnano-, nano- and submicron-surface features on osteoblast differentiation of bone marrow mesenchymal stem cells.

Subnano, nano and sub-micron surface features can selectively activate integrin receptors and induce osteoblast differentiation of bone marrow mesenchymal stem cells. Although it is widely accepted that nanoscale titanium surface roughness may promote differentiation of various osteoblast lineages, there has been no clear report on the threshold dimension of surface features and the optimized dimensions of surface features for triggering integrin activation and stem cell differentiation. This study systematically controlled titanium surface features from the sub-nano to sub-micron scales and investigated the corresponding effects on stem cell responses, such as integrin activation, cyclins, key transcriptional genes of osteoblast differentiation and osteoblastic phenotype genes.

Arresting cancer proliferation by controlling the surface crystallinity of carbon materials without generating reactive oxygen species.

This study demonstrated that the surface crystallinity of carbon nanostructures is an additional independent factor that should be considered for the inhibition of cancer proliferation without activating reactive oxygen species (ROS). In addition, cytotoxic evaluation of both proliferating cancer cells and fully differentiated nerve cells (i.e.

Effect of precursor supply on structural and morphological characteristics of fe nanomaterials synthesized via chemical vapor condensation method.

Various physical, chemical and mechanical methods, such as inert gas condensation, chemical vapor condensation, sol-gel, pulsed wire evaporation, evaporation technique, and mechanical alloying, have been used to synthesize nanoparticles. Among them, chemical vapor condensation (CVC) has the benefit of its applicability to almost all materials because a wide range of precursors are available for large-scale production with a non-agglomerated state. In this work, Fe nanoparticles and nanowires were synthesized by chemical vapor condensation method using iron pentacarbonyl (Fe(CO)5) as the precursor.

Behavior of NiTiNb SMA wires under recovery stress or prestressing.

The recovery stress of martensitic shape-memory alloy [SMA] wires can be used to confine concrete, and the confining effectiveness of the SMA wires was previously proved through experimental tests. However, the behavior of SMA wires under recovery stress has not been seriously investigated. Thus, this study conducted a series of tests of NiTiNb martensitic SMA wires under recovery stress with varying degrees of prestrain on the wires and compared the behavior under recovery stress with that under prestressing of the wires.