Biodegradable Polyhydroxyalkanoates with a Different Set of Valerate Monomers: Chemical Structure and Physicochemical Properties.

The properties, features of thermal behavior and crystallization of copolymers containing various types of valerate monomers were studied depending on the set and ratio of monomers. We synthesized and studied the properties of three-component copolymers containing unusual monomers 4-hydroxyvalerate (4HV) and 3-hydroxy-4-methylvalerate (3H4MV), in addition to the usual 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV) monomers. The results showed that P(3HB--3HV--4HV) and P(3HB--3HV--3H4MV) terpolymers tended to increase thermal stability, especially for methylated samples, including an increase in the gap between melting point (T) and thermal degradation temperature (T), an increase in the melting point and glass transition temperature, as well as a lower degree of crystallinity (40-46%) compared with P(3HB--3HV) (58-66%).

Three-Dimensional Printing of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] Biodegradable Scaffolds: Properties, In Vitro and In Vivo Evaluation.

The results of constructing 3D scaffolds from degradable poly(3-hydrosbutyrpate-co-3-hydroxyvalerate) using FDM technology and studying the structure, mechanical properties, biocompatibility in vitro, and osteoplastic properties in vivo are presented. In the process of obtaining granules, filaments, and scaffolds from the initial polymer material, a slight change in the crystallization and glass transition temperature and a noticeable decrease in molecular weight (by 40%) were registered. During the compression test, depending on the direction of load application (parallel or perpendicular to the layers of the scaffold), the 3D scaffolds had a Young's modulus of 207.

Effect of Monomers of 3-Hydroxyhexanoate on Properties of Copolymers Poly(3-Hydroxybutyrate- 3-Hydroxyhexanoate).

The properties of poly(3-hydroxybutyrate--3-hydroxyhexanoate) P(3HB--3HHx) copolymers with different ratios of monomers synthesized by the wild-type strain B-10646 on sugars, and an industrial sample from Kaneka synthesized by the recombinant strain NSDG-ΔfadB1 on soybean oil, were studied in a comparative aspect and in relation to poly(3-hydroxybutyrate) P(3HB). The copolymer samples, regardless of the synthesis conditions or the ratio of monomers, had reduced values of crystallinity degree (50-60%) and weight average molecular weight (415-520 kDa), and increased values of polydispersity (2.8-4.

Assessment of the efficacy of slow-release formulations of the tribenuron-methyl herbicide in field-grown spring wheat.

The efficacy of slow-release formulations of tribenuron-methyl (TBM) embedded in the matrix of degradable poly(3-hydroxybutyrate) blended with birch wood flour [polymer/wood flour/herbicide 50/30/20 wt.%] was compared with the efficacy of TBM as the active ingredient of the Mortira commercial formulation, which was applied as post-emergence spray to treat spring wheat cv. Novosibirskaya 15.

Properties of degradable polyhydroxyalkanoates with different monomer compositions.

Purpose: To synthesize and investigate polyhydroxyalkanoates (PHAs) with different monomer composition and percentages and polymer films prepared from them.

Results: Various PHAs: homopolymer poly-3-hydroxybutyrate P(3HB) and 2-, 3-, and 4-component copolymers comprising various combinations of 3-hydroxybutyrate (3HB), 3-hydroxyvalerate (3HV), 4-hydroxybutyrate (4HB), and 3-hydroxyhexanoate (3HHx) monomers were synthesized under specialized conditions. Relationships were found between the monomer composition of PHAs and their molecular-weight and thermal properties and degree of crystallinity.

Poly-3-hydroxybutyrate/chitosan composite films and nonwoven mats.

Composite films and nonwoven mats of the poly-3-hydroxybutyrate and chitosan natural polymers were prepared and investigated. DSC and FTIR techniques were used to confirm that P(3HB) blending with chitosan resulted in a decrease in P(3HB) crystallinity to 47% and 62% in the films and nonwoven mats, respectively. Scanning electron microscopy showed that addition of chitosan induced changes in the surface morphology of the composite films and a reduction in the diameter of ultrafine fibers in the nonwoven mats from 800 nm to 460 nm.

Efficacy of Slow-Release Formulations of Metribuzin and Tribenuron Methyl Herbicides for Controlling Weeds of Various Species in Wheat and Barley Stands.

The herbicidal activity of long-acting formulations of metribuzin and tribenuron methyl herbicides embedded in granules prepared from a mixture of degradable poly(3-hydroxybutyrate) and birch wood flour was studied in laboratory-grown weeds of various species and in wheat and barley stands infested by weeds. The constructed formulations effectively suppressed all species of weeds studied. The biological effectiveness of herbicide formulations toward intact plants in wheat and barley stands infested with weeds was close to 100%, which was significantly higher than the effect of their free forms.

Production of Porous Films Based on Biodegradable Polyesters by the Casting Solution Technique Using a Co-Soluble Porogen (Camphor).

Porous films have been prepared from degradable polymers-poly-3-hydroxybutyrate (PHB), poly-ε-caprolactone (PCL) and a blend of these polymers (1:3)-by adding porogen (camphor) to the polymer solution at 10%, 30% or 50% of the total mass of the polymer and porogen, and leaching it out afterwards. After the rinse, camphor content in films decreased to about 0.025%.

Biological effects of the free and embedded metribuzin and tribenuron-methyl herbicides on various cultivated weed species.

The present study addresses the herbicidal activity and biological effects of the metribuzin (MET) and tribenuron-methyl (TBM) herbicides used to control various weed species ( and ). The effects of the free herbicides and the herbicides embedded in granules of degradable polymer poly-3-hydroxybutyrate [P(3HB)] blended with birch wood flour were compared. Metribuzin, regardless of the form, caused 100% mortality of the three weeds by day 21.

Thermal, mechanical and biodegradation studies of biofiller based poly-3-hydroxybutyrate biocomposites.

Biodegradable poly-3-hydroxybutyrate [P(3HB)] and natural fillers - clay, peat, and birch wood flour - were used to prepare powdered composites to form pellets and granules. Pellets were produced by cold pressing of polymer and filler powder whereas granules were produced from the powders wetted with ethanol. Characterization techniques like IR spectroscopy, differential scanning calorimetry, X-ray analysis, mechanical analysis and electron microscopy were employed to study the properties of the initial P(3HB) and fillers and the composites.

Production and properties of bacterial cellulose by the strain Komagataeibacter xylinus B-12068.

A strain of acetic acid bacteria, Komagataeibacter xylinus B-12068, was studied as a source for bacterial cellulose (BC) production. The effects of cultivation conditions (carbon sources, temperature, and pH) on BC production and properties were studied in surface and submerged cultures. Glucose was found to be the best substrate for BC production among the sugars tested; ethanol concentration of 3% (w/v) enhanced the productivity of BC.

Electrospinning of polyhydroxyalkanoate fibrous scaffolds: effects on electrospinning parameters on structure and properties.

In this study, electrospinning was used to prepare ultrafine fibers from PHAs with different chemical compositions: P(3HB) and copolymers: P(3HB-co-4HB), P(3HB-co-3HV), and P(3HB-co-3HHx). The main process parameters that influence ultrafine fiber diameter and properties (polymer concentration, solution feeding rate, working distance, and applied voltage) have been investigated and their effects evaluated. The study revealed electrospinning parameters for the production of high-quality ultrafine fibers and determined which parameters should be varied to tailor the properties of the products.

[Radioecological monitoring of the Yenisei River and citological characterization of a submerged aquatic plant Elodea canadensis].

The study was devoted to investigation of the contents of radionuclides and of heavy metals and to evaluate the frequency of chromosomal aberrations in samples of Elodea canadensis, a submerged plant, collected in different parts of the Yenisei River. The samples were collected in the area subjected to radioactive impact of the Mining-and-Chemical Combine (MCC) at Zheleznogorsk and in the control area, upstream of the MCC. The investigations shown that elodea biomass in the area affected by MCC operation contained a long inventory of artificial radionuclides typical for the MCC discharges.

[Radioactive contamination of aquatic organisms of the Yenisei River in the area affected by the activity of the Mining-and-Chemical Combine].

The study was done to investigate the content of manmade radionuclides in aquatic organisms of the Yenisei River near the Mining-and-Chemical Combine (MCC) and to estimate the exposure dose rates to organisms from various sources. The results of the investigation and calculations suggest that the main source of radioactive contamination of aquatic organisms is the coolant of the third MCC reactor, which is still being released into the Yenisei. Gamma-spectrometric analysis revealed 23 manmade radionuclides in the biomass of aquatic plants.