A generic approach to estimate airborne concentrations of substances released by indoor spray processes using a deterministic 2-box model.

Sprays are used both in workplace and consumer settings. Although spraying has advantages, such as uniform distribution of substances on surfaces in a highly efficient manner, it is often associated with a high inhalation burden. For an adequate risk assessment, this exposure has to be reliably quantified.

Inhalation and dermal exposure to biocidal products during foam and spray applications.

Objectives: Foaming and spraying are common application techniques for biocidal products. In the past, inhalation and dermal exposure during spraying have been investigated extensively. Currently, however, no exposure data are available for foaming, hindering a reliable risk assessment for foam applications of biocidal products.

Aerosol formation during foam application of non-volatile biocidal substances.

The application of biocidal products by foam is considered an alternative to droplet spraying when disinfecting surfaces or fighting infestations. Inhalation exposure to aerosols containing the biocidal substances cannot be ruled out during foaming. In contrast to droplet spraying, very little is known about aerosol source strength during foaming.

Exposure modelling in Europe: how to pave the road for the future as part of the European Exposure Science Strategy 2020-2030.

Exposure models are essential in almost all relevant contexts for exposure science. To address the numerous challenges and gaps that exist, exposure modelling is one of the priority areas of the European Exposure Science Strategy developed by the European Chapter of the International Society of Exposure Science (ISES Europe). A strategy was developed for the priority area of exposure modelling in Europe with four strategic objectives.

Modelling Exposure by Spraying Activities-Status and Future Needs.

Spray applications enable a uniform distribution of substances on surfaces in a highly efficient manner, and thus can be found at workplaces as well as in consumer environments. A systematic literature review on modelling exposure by spraying activities has been conducted and status and further needs have been discussed with experts at a symposium. This review summarizes the current knowledge about models and their level of conservatism and accuracy.

Solvent Transfer-Efficiency of Risk Management Measures.

A series of laboratory simulations were conducted in order to determine the airborne protection that might be afforded by different combinations of workplace exposure controls typically encountered when handling volatile solvents (e.g. solvent transfer).

Evaluation of acute-to-chronic ratios of fish and to predict acceptable no-effect levels.

Background: Acute-to-chronic extrapolation is an important approach to predict acceptable no-effect levels from acute data which has some uncertainties, but is valuable for risk assessment of chemical substances. With regard to the still limited and heterogenic data of chronic fish tests, conclusions on aquatic hazard estimation need to be checked and the question arises whether the chronic toxicity to fish can be adequately derived from acute data. A comprehensive dataset including ecotoxicological studies of 203 substances was used to investigate acute-to-chronic ratios (ACR) for both fish and .

Simulation Studies to Explore Biodegradation in Water-Sediment Systems: From OECD 308 to OECD 309.

Studies according to OECD 308 and OECD 309 are performed to simulate the biodegradation of chemicals in water-sediment systems in support of persistence assessment and exposure modeling. However, several shortcomings of OECD 308 have been identified that hamper data evaluation and interpretation, and its relation to OECD 309 is still unclear. The present study systematically compares OECD 308 and OECD 309 and two variants thereof to derive recommendations on how to experimentally address any shortcomings and improve data for persistence and risk assessment.

Bridging across OECD 308 and 309 Data in Search of a Robust Biotransformation Indicator.

The OECD guidelines 308 and 309 define simulation tests aimed at assessing biotransformation of chemicals in water-sediment systems. They should serve the estimation of persistence indicators for hazard assessment and half-lives for exposure modeling. Although dissipation half-lives of the parent compound are directly extractable from OECD 308 data, they are system-specific and mix up phase transfer with biotransformation.

Evaluation of the integrated testing strategy for PNEC derivation under REACH.

Species sensitivity evaluation represents an approach to avoid chronic toxicity testing of aquatic vertebrates in accordance with the animal welfare concept of the EU chemicals regulation. In this study a data set of chemicals is analysed for relative species sensitivity between Daphnia and fish in chronic testing to evaluate under what condition chronic fish tests can be waived without underestimating the environmental hazard. Chronic fish toxicity is covered in 84% of the evaluated substances by the chronic invertebrate test and an assessment factor of 50.

Claudin-4-targeted optical imaging detects pancreatic cancer and its precursor lesions.

Objectives: Novel imaging methods based on specific molecular targets to detect both established neoplasms and their precursor lesions are highly desirable in cancer medicine. Previously, we identified claudin-4, an integral constituent of tight junctions, as highly expressed in various gastrointestinal tumours including pancreatic cancer. Here, we investigate the potential of targeting claudin-4 with a naturally occurring ligand to visualise pancreatic cancer and its precursor lesions in vitro and in vivo by near-infrared imaging approaches.

Consumer exposure to biocides--identification of relevant sources and evaluation of possible health effects.

Background: Products containing biocides are used for a variety of purposes in the home environment. To assess potential health risks, data on products containing biocides were gathered by means of a market survey, exposures were estimated using a worst case scenario approach (screening), the hazard of the active components were evaluated, and a preliminary risk assessment was conducted.

Methods: Information on biocide-containing products was collected by on-site research, by an internet inquiry as well as research into databases and lists of active substances.

Emission of biocides from hospitals: comparing current survey results with European Union default values.

Under the European Union (EU) Biocidal Products Directive 98/8/EC, comprehensive evaluations on substances of the Third Priority List were conducted until 31 July 2007. This list includes, among other categories, disinfectants for human hygiene (e.g.

Comparative studies on algal toxicity testing using fluorometric microplate and Erlenmeyer flask growth-inhibition assays.

Two fluorometric microplate algae growth-inhibition assays with a liquid volume of 2 mL and 200 microL per well are presented, and comparative studies on the toxicity of chemicals are carried out with Erlenmeyer flask assays. The test procedures are in accordance with the standards ISO 8692 (DIN 38412 L9 and EN 28692), OECD 201 and DIN 38412 L33. By testing four toxicants several times laboratory internal repeatability is proven.

Assessment of the influence of use on ecotoxicological characteristics of synthetic ester lubricants.

Synthetic ester lubricants need optimisation about their technical and their ecotoxicological characteristics. To determine the ecotoxicological potential the required examinations can be based on the procedure for a risk assessment of chemicals. At present risk classification of lubricant oils is carried out with new oil fluids that are normally prepared before application in aqueous bioassays.

Biodegradability testing of synthetic ester lubricants--effects of additives and usage.

The optimised biodegradability test system "O2/CO2 Headspace Test with GC-TCD" is used for the assessment of synthetic ester lubricants. The effects of both additives and usage on biodegradability are examined and discussed. Ester based cutting fluids and hydraulic fluids with and without additives are used under defined conditions at machine tools and hydraulic and plain bearing test benches.