Stress analysis of intervertebral disc during occupational activities.

Background And Objective: Manual material handling activities cause large compression of the intervertebral disc of the lumbar spine. Intradiscal pressure (IDP) has generally been employed to predict the risk of low back injury. As an alternative to in vivo measurements, either motion analysis or finite element (FE) analysis has been used to estimate IDP.

Finite element analysis of knee and ankle joint during gait based on motion analysis.

Contact pressures in the articular cartilage during gait affect injuries and the degenerative arthritis of knee and ankle joints. However, only contact forces at the knee and ankle joints during gait can be estimated by using a rigid body dynamic model. The contact pressure distribution can be obtained quantitatively for a static posture by using finite element (FE) analysis in most cases.

Effect of structural design on the pullout strength of suture anchors for rotator cuff repair.

Various types of suture anchor designs are currently available for rotator cuff repair. The purpose of our study was to investigate the pullout strength of such anchors based on their structural design and the predominant geometric design factors affecting the pullout strength using finite element analysis. Finite element models were constructed using five cadaveric humeri and ten suture anchors with different designs.

Primary stability of inferior tilt fixation of the glenoid component in reverse total shoulder arthroplasty: A finite element study.

Glenoid component fixation with inferior tilt has been suggested as one of the surgical methods to decrease scapular notching and improve stability, but its clinically beneficial effect remains a concern. We evaluated the influence of inferior tilt fixation of the glenoid component on primary stability in reverse total shoulder arthroplasty by finite element analysis. Finite element models were constructed from cadaveric scapulae of females over the age of 60 years and glenoid components from reverse total shoulder arthroplasty.

Effect of baseplate size on primary glenoid stability and impingement-free range of motion in reverse shoulder arthroplasty.

Background: Use of a baseplate with a smaller diameter in reverse shoulder arthroplasty is increasing, especially in patients with a small glenoid or glenoid wear. However, the effect of a smaller baseplate on stability of the glenoid component has not been evaluated. Thus, the purpose of this study was to determine whether a smaller baseplate (25 mm) is beneficial to the initial stability of the glenoid component compared to that with a baseplate of a commonly used size (29 mm).

Lipid crystals mechanically stimulate adjacent extracellular matrix in advanced atherosclerotic plaques.

Objective: Although lipid crystals (LCs) have received attention as a causative factor of plaque rupture, the mechanisms by which they increase plaque vulnerability are unknown. We examined whether solid-state LCs physically affect the adjacent extracellular matrix (ECM) using a combination of multimodal nonlinear optical (MNLO) imaging and finite element analysis (FEA).

Methods: The changes of ECMs affected by lipids in atherosclerotic arteries in apolipoprotein E-deficient mice (n = 32) fed a high-fat diet for 20-30 weeks were micro-anatomically visualized by a 3D MNLO imaging platform including CARS for lipids, TPEF for elastin, and SHG for collagen.

Biomechanical effect of altered lumbar lordosis on intervertebral lumbar joints during the golf swing: a simulation study.

Although the lumbar spine region is the most common site of injury in golfers, little research has been done on intervertebral loads in relation to the anatomical-morphological differences in the region. This study aimed to examine the biomechanical effects of anatomical-morphological differences in the lumbar lordosis on the lumbar spinal joints during a golf swing. The golf swing motions of ten professional golfers were analyzed.

Effect of Poloxamer 407 as a carrier vehicle on rotator cuff healing in a rat model.

Background: In vivo studies showing the effects of biologic healing-promoting factors on tendon-to-bone healing after rotator cuff repair have focused only on biologic healing-promoting factors and have not taken into consideration the effect of the carrier vehicle. Moreover, most studies have evaluated the healing process using different carrier vehicles, each of which may have specific effects on tendon healing. This may explain the large variability seen in outcomes in research studies.

Biocompatibility and strength retention of biodegradable Mg-Ca-Zn alloy bone implants.

The biocompatibility and strength retention of a Mg-Ca-Zn alloy were studied to evaluate its efficacy for osteosynthesis applications. Mg-Ca-Zn alloy and self-reinforced poly l-lactide (SR-PLLA) bone screws were implanted into New Zealand rabbits for radiography analysis, micro computed tomography analysis, histomorphometry, hematology, serum biochemistry, histopathology, and inductively coupled plasma mass spectrometry analysis. Bending and torsion tests were performed on intact specimens to find the initial mechanical strength of these Mg-Ca-Zn alloy bone screws.

Load-bearing capacity and biological allowable limit of biodegradable metal based on degradation rate in vivo.

In this study, a newly developed Mg-Ca-Zn alloy for low degradation rate and surface erosion properties was evaluated. The compressive, tensile, and fatigue strength were measured before implantation. The degradation behavior was evaluated by analyzing the microstructure and local hardness of the explanted specimen.