Sampling of respirable isocyanate particles.

An advanced design of a denuder impactor (DI) sampler has been developed for characterization of possible airborne isocyanate exposure in different particle size fractions. The sampler is equipped with 12 different parallel denuder tubes, 4 impaction stages with the cut-off values (d50) of: 9.5, 4, 2.

Dry sampling of gas-phase isocyanates and isocyanate aerosols from thermal degradation of polyurethane.

The performance of a dry sampler, with an impregnated denuder in series with a glass fibre filter, using di-n-butylamine (DBA) for airborne isocyanates (200ml min(-1)) is investigated and compared with an impinger flask with a glass fibre filter in series (1 l min(-1)). An exposure chamber containing 1,6-hexamethylene diisocyanate (HDI), isophorone diisocyanate (IPDI), and 2,4- and 2,6-toluene diisocyanate (TDI) in the concentration range of 5-205 μg m(-3) [0.7-33 p.

Determination of aromatic amines in aqueous extracts of polyurethane foam using hydrophilic interaction liquid chromatography and mass spectrometry.

A method is presented for the determination of aromatic amines in aqueous extracts of polyurethane (PUR) foam. The method is based on the extraction of PUR foam using aqueous acetic acid (0.1%, w/v) followed by determination of extracted aromatic amines using hydrophilic interaction liquid chromatography (HILIC) and tandem mass spectrometry (MS/MS) with positive electrospray ionisation.

Adsorption efficiency of respirator filter cartridges for isocyanates.

In some industries, the temperature and the humidity will vary greatly between different work places, such as outdoor work in arctic or tropical climates. There is therefore a need to test respirator filters at conditions that simulate conditions that are relevant for the industries that they are used in. Filter cartridges were exposed to controlled atmospheres of varying isocyanate concentration, air humidity, and temperature in an exposure chamber.

Validation of transferability of DBA derivatization and LC-MS/MS determination method for isocyanates via an interlaboratory comparison.

An adapted method for the quantitative determination of isocyanates in air was implemented and validated in-house. The method was based on air sampling using an impinger flask containing di-n-butylamine (DBA) in toluene and a glass fibre filter in series. The DBA derivatives were determined using liquid chromatography and tandem mass spectrometry.

Size-separated sampling and analysis of isocyanates in workplace aerosols. Part I. Denuder--cascade impactor sampler.

Isocyanates in the workplace atmosphere are typically present both in gas and particle phase. The health effects of exposure to isocyanates in gas phase and different particle size fractions are likely to be different due to their ability to reach different parts in the respiratory system. To reveal more details regarding the exposure to isocyanate aerosols, a denuder-impactor (DI) sampler for airborne isocyanates was designed.

Size-separated sampling and analysis of isocyanates in workplace aerosols--Part II: aging of aerosols from thermal degradation of polyurethane.

A new type of isocyanate sampler has been used to investigate aging aerosols generated during thermal degradation of polyurethane (PUR). The sampler consists of a denuder connected in series with a three-stage cascade impactor and a filter. The denuder collects gas-phase isocyanates.

Is it possible to improve the patch-test diagnostics for isocyanates? A stability study of petrolatum preparations of diphenylmethane-4,4'-diisocyanate and polymeric diphenylmethane diisocyanate.

We have previously shown that the concentration of diphenylmethane-4,4'-diisocyanate (4,4'-MDI) in commercial test preparations was so low that patch testing with the same was not reliable. The stability of 4,4'-MDI in petrolatum (pet.) was compared with pet.

Chemical analysis of 2,4-toluene diisocyanate, 1,6-hexamethylene diisocyanate and isophorone diisocyanate in petrolatum patch-test preparations.

Background: Isocyanates with the general formula R-(N=C=O) are theoretically contact sensitizers. However, allergic contact dermatitis (ACD) from isocyanates is seldom reported. In previous reports, patients reacted to their isocyanate-based work materials but not to commercial patch-test preparations of isocyanates.

Inhalation exposure to isocyanates of car body repair shop workers and industrial spray painters.

As part of a large-scale epidemiological study, occupational isocyanate exposure was assessed in spray-painting environments. The aim was to assess which compounds contribute to isocyanate exposure in car body repair shops and industrial painting companies, and to identify tasks with high risk of isocyanate exposure. Mainly personal task-based samples (n = 566) were collected from 24 car body repair shops and five industrial painting companies using impingers with DBA in toluene.

Solvent-free sampling with di-n-butylamine for monitoring of isocyanates in air.

The solvent-free sampler for airborne isocyanates consisted of a polypropylene tube with an inner wall coated with a glass fibre filter, coupled in series with a 13 mm glass fibre filter. The filters were impregnated with reagent solution containing equimolar amounts of di-n-butylamine (DBA) and acetic acid. Air sampling was performed with an air flow of 0.

Poor correlation between stated and found concentrations of diphenylmethane-4,4'-diisocyanate (4,4'-MDI) in petrolatum patch-test preparations.

Diphenylmethane diisocyanate (MDI) is widely used in its polymeric form in the manufacturing of polyurethane products. Previous reports on MDI-related contact allergy have shown a pattern, where patients seem to react to their own MDI-based work material but not to commercial patch-test preparations, which contain 4,4'-MDI. Therefore, we performed chemical analyses of 14 commercial test preparations of 4,4'-MDI obtained from 8 European and 4 American dermatology departments as well as 2 preparations from 2 major European suppliers of patch-test allergens.

Determination of airborne anhydrides using LC-MS monitoring negative ions of di-n-butylamine derivatives.

An air sampling method for simultaneous determination of organic acid anhydrides and isocyanates is presented. Air samples are collected in impinger flasks filled with 0.01 M di-n-butylamine (DBA) in a mixture of toluene-acetonitrile (7:3, v/v) with a 13 millimetre glass fibre filter in series.

Determination of technical grade isocyanates used in the production of polyurethane plastics.

A method for determination of technical grade isocyanates used in the production of polyurethane (PUR) is presented. The isocyanates in technical grade products were characterised as di-n-butylamine (DBA) derivatives using LC-MS and LC-chemiluminescent nitrogen detection (CLND) and the total isocyanate content was compared to a titration assay. For collection of isocyanates in air, an impinger-filter sampling technique with DBA as derivatisation reagent was used.

Determination of amines as pentafluoropropionic acid anhydride derivatives in biological samples using liquid chromatography and tandem mass spectrometry.

Determination of amines in biological samples as markers of exposure to the amines or the corresponding isocyanates is an important tool for industrial exposure assessment. In this study, a liquid chromatography and tandem mass spectrometry (LC-MS/MS) method for determination of amines in biological samples as perfluorofatty amides derivatives is presented. The method enables determination of diamines such as methylene diamine (MDA), toluene diamine (TDA), naphthalene diamine (NDA), hexamethylene diamine (HDA), isophorone diamine (IPDA), methylenedi(cyclohexylamine)(HMDA) and 4,4'-methylene-(2-chloroaniline)(MOCA) in human urine and plasma.

Effects of thermal degradation products from polyurethane foams based on toluene diisocyanate and diphenylmethane diisocyanate on isolated, perfused lung of guinea pig.

Objectives: The composition of thermal degradation products from two types of polyurethane foams, one based on toluene diisocyanate (TDI) and the other on diphenylmethane diisocyanate (MDI), was analyzed and their toxic lung effects were compared.

Methods: Isolated perfused lungs of guinea pig were subjected to thermal decomposition products of polyurethane foams from an aerosol generator with compartments for diluting, mixing, and sampling.

Results: Thermal degradation of MDI-based polyurethane foams released MDI, phenyl isocyanate, and methyl isocyanate.

Exposure and nasal inflammation in workers heating polyurethane.

Objective: To test the hypothesis that exposure to thermal-degradation products of polyurethane (PUR), particularly isocyanates, induced nasal inflammation.

Methods: Thirty-eight workers -14 with a history of work-related nasal symptoms (WRS/Nose), and 15 referents without such history - exposed to sprayed and heated PUR glue, were studied with regard to biomarkers of isocyanate exposure [4,4'-diphenylmethane diisocyanate (4,4'-methylenediphenyl diisocyanate; MDI) and 2,4- and 2,6-toluene diisocyanate (TDI), determined as 4,4'-diphenylmethane (U-MDX) and 2,4- and 2,6-toluene (U-2,4 and U-2,6-TDX) diamine in hydrolysed urine and nasal lavage fluid (NAL)], inflammation [albumin; eosinophilic cationic protein (ECP); myeloperoxidase (MPO) and cells in NAL], serum IgG specific for MDI (S-IgG-MDI) and TDI (S-IgG-TDI), and nose symptoms. Nine unexposed office workers were also examined.

Determination of isocyanates, aminoisocyanates and amines in air formed during the thermal degradation of polyurethane.

An air sampling method for the determination of isocyanates, aminoisocyanates and amines formed during the thermal degradation of polyurethane (PUR) is presented. The method is based on the collection of air samples using impinger flasks containing di-n-butylamine (DBA) in toluene with a glass fibre filter in series. Isocyanates are derivatized with DBA to urea derivatives, and amines are derivatized in a subsequent work-up procedure with ethyl chloroformate (ET) to carbamate esters.

Determination of isocyanic acid in air.

A method is presented for the determination of isocyanic acid (ICA), HNCO, in air samples as a di-n-butylamine (DBA) derivative. The method is based on sampling in midget impinger flasks containing 10 ml of 0.01 mol l-1 DBA in toluene.

Characterization of thermally generated aerosols from polyurethane foam.

Isocyanates constitute a group of highly reactive chemicals used on a large scale for the production of flexible polyurethane (PUR) foam. Exposure to isocyanates is known to produce irritation of the mucous membranes and the eyes. Isocyanates also have strong sensitizing properties and may cause occupational asthma.

Airborne thermal degradation products of polyurethene coatings in car repair shops.

A methodology for workplace air monitoring of aromatic and aliphatic, mono- and polyisocyanates by derivatisation with di-n-butylamine (DBA) is presented. Air sampling was performed using midget impinger flasks containing 10 ml of 0.01 mol l(-1) DBA in toluene and a glass-fibre filter in series after the impinger flask, thereby providing the possibility of collecting and derivatising isocyanates in both the gas and particle phases.

Assessment of environmental tobacco smoke exposure in children with asthmatic symptoms by questionnaire and cotinine concentrations in plasma, saliva, and urine.

To validate a detailed questionnaire for assessment of environmental tobacco smoke (ETS) exposure by the biomarker cotinine in various media, a population-based study in the urban area of Malmö, Sweden was performed in children aged 8-13 years with and without asthmatic symptoms. There were strong correlations between urinary and saliva cotinine concentrations and also, though to a lesser extent, between these media and plasma. Even a detailed questionnaire gave only a rough picture of the ETS exposure, as indicated by the biomarkers.

Exposure biomarkers and risk from gluing and heating of polyurethane: a cross sectional study of respiratory symptoms.

Objectives: To define the relation between exposure to polyurethane (PUR) glue, biomarkers of exposure and effect, and work related symptoms that occur at least once a week.

Methods: In a cross sectional study, 152 workers and 14 clerks in a factory with exposure to sprayed and heated PUR glue containing 4, 4'-diphenylmethane (MDI) or 1,6-hexamethylene (HDI) di-isocyanate were examined with gas chromatography-mass spectrometry (GC-MS) for metabolites of MDI in plasma (P-MDX) and urine (U-MDX), 2,4- and 2, 6-toluene di-isocyanate (TDI; P-TDX, U-TDX) and HDI in plasma and urine, specific serum IgG (S-IgG-MDI, S-IgG-HDI, and S-IgG-TDI, respectively) and IgE (S-IgE-MDI). Work related symptoms of the eyes and airways (nose or lower airways, or both), and lung function were also evaluated.

Urinary cotinine concentration in flight attendants, in relation to exposure to environmental tobacco smoke during intercontinental flights.

Objectives: To measure and compare the urinary cotinine concentration (U-cotinine) in non-smoking cabin attendants (C/A) working with the Scandinavian Airlines System, before and after work on intercontinental flights with exposure to environmental tobacco smoke (ETS).

Methods: The study material consisted of 24 cabin attendants and one pilot, all volunteers and all without exposure to ETS in the home, working on 15 intercontinental flights. Information on age, gender and occupation was gathered, as well as possible sources of ETS exposure in other places, outside work and during previous flights, during a 3-day period prior to the investigation.

Determination of complex mixtures of airborne isocyanates and amines. Part 5. Determination of low molecular weight aliphatic isocyanates as dibutylamine derivatives.

A method is presented for the determination of low molecular weight aliphatic isocyanates, methyl isocyanate (MIC), ethyl isocyanate (EIC), propyl isocyanate (PIC) and butyl isocyanate (BIC), as their dibutylamine (DBA) derivatives. The method is based on sampling in midget impinger flasks containing 10 ml of 0.01 mol l-1 DBA in toluene (as in Parts 1-4 in this series).