Effective Light Trapping in Thin Film Silicon Solar Cells with Nano- and Microscale Structures on Glass Substrate.

For thin film silicon-based solar cells, effective light trapping at a broad range of wavelengths (400-1100 nm) is necessary. Normally, etching is only carried out with TCOs, such as SnO2:F and impurity doped ZnO, to form nano-sized craters in the surface morphology to confer a light trapping effect. However, in this study, prior to ZnO:Al etching, periodic structures on the glass substrates were made by photolithography and wet etching to increase the light scattering and internal reflection.

Method for Fabricating Textured High-Haze ZnO:Al Transparent Conduction Oxide Films on Chemically Etched Glass Substrates.

We developed a technique for forming textured aluminum-doped zinc oxide (ZnO:Al) transparent conductive oxide (TCO) films on glass substrates, which were etched using a mixture of hydrofluoric (HF) and hydrochloric (HCl) acids. The etching depth and surface roughness increased with an increase in the HF content and the etching time. The HF-based residues produced insoluble hexafluorosilicate anion- and oxide impurity-based semipermeable films, which reduced the etching rate.

Investigation of Electrical and Optical Properties of Highly Transparent TCO/Ag/TCO Multilayer.

Transparent conductive oxides (TCOs) have been widely used as transparent electrodes for opto-electronic devices, such as solar cells, flat-panel displays, and light-emitting diodes, because of their unique characteristics of high optical transmittance and low electrical resistivity. Among various TCO materials, zinc oxide based films have recently received much attention because they have advantages over commonly used indium and tin-based oxide films. Most TCO films, however, exhibit valleys of transmittance in the wavelength range of 550-700 nm, lowering the average transmittance in the visible region and decreasing short-circuit current (Isc) of solar cells.

Study of low resistivity and high work function ITO films prepared by oxygen flow rates and N2O plasma treatment for amorphous/crystalline silicon heterojunction solar cells.

Pulsed DC magnetron sputtered indium tin oxide (ITO) films deposited on glass substrates with lowest resistivity of 2.62 x 10(-4) Ω x cm and high transmittance of about 89% in the visible wavelength region. We report the enhancement of ITO work function (Φ(ITO)) by the variation of oxygen (O2) flow rate and N2O surface plasma treatment.

Effects of target angle on the properties of aluminum doped zinc oxide films prepared by DC magnetron sputtering for thin film solar cell applications.

An aluminum doped zinc oxide (AZO) films for front contacts of thin film solar cells, in this work, were prepared by DC magnetron sputtering with different target angles. Effects of target angles on the structural and electro-optical properties of AZO films were investigated. Also, to clarify the light trapping of textured AZO film, amorphous silicon thin film solar cells were fabricated on the textured AZO/glass substrate and the performance of solar cells were studied.

Fabrication of ZnO nanorods for gas sensing applications using hydrothermal method.

We showed well-aligned zinc oxide (ZnO) nanorod arrays synthesized using hydrothermal method at atmospheric pressure. The influence of fabrication conditions such as Zn2+/hexamethylentriamin concentration ratio, and growth temperature on the formation of ZnO nanorods was investigated. Scanning Electron Microscope (SEM) images and X-ray Diffraction (XRD) analysis were used to confirm the single crystal of ZnO nanorods, which showed wurtzite structure with growth direction of [0001] (the c-axis).

Enhancing light trapping properties of thin film solar cells by plasmonic effect of silver nanoparticles.

The preparation of thin film silicon solar cells containing Ag nanoparticles is reported in this article. Ag nanoparticles were deposited on fluorine doped tin oxide coated glass substrates by the evaporation and condensation method. a-Si:H solar cells were deposited on these substrates by cluster type plasma enhanced chemical vapor deposition.

Inserted layer of AZO thin film with high work function between transparent conductive oxide and p-layer and its solar cell application.

We report aluminum doped zinc oxide (AZO) films with high work function as an insertion layer between transparent conducting oxides (TCO) and hydrogenated amorphous silicon carbide (a-SiC:H) layer to improve open circuit voltage (V(oc)) and fill factor (FF) for thin film solar cells. Amorphous silicon (a-Si:H) solar cells exhibit poor fill factors due to a Schottky barrier at the interface between a-SiC:H window and TCO. The interface engineering is carried out by inserting an AZO layer with high work function (4.