Sampling and recovery of infectious SARS-CoV-2 from high-touch surfaces by sponge stick and macrofoam swab.

Effective sampling for severe acute respiratory syndrome 2 (SARS-CoV-2) is a common approach for monitoring disinfection efficacy and effective environmental surveillance. This study evaluated sampling efficiency and limits of detection (LODs) of macrofoam swab and sponge stick sampling methods for recovering infectious SARS-CoV-2 and viral RNA (vRNA) from surfaces. Macrofoam swab and sponge stick methods were evaluated for collection of SARS-CoV-2 suspended in a soil load from 6-in coupons composed of four materials: stainless steel (SS), acrylonitrile butadiene styrene (ABS) plastic, bus seat fabric, and Formica.

Efficacy of chemical disinfectants against SARS-CoV-2 on high-touch surface materials.

Aims: This study aimed to provide operationally relevant severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) surface disinfection efficacy information.

Methods And Results: Three EPA-registered disinfectants (Vital Oxide, Peroxide, and Clorox Total 360) and one antimicrobial formulation (CDC bleach) were evaluated against SARS-CoV-2 on material coupons and were tested using Spray (no touch with contact time) and Spray & Wipe (wipe immediately post-application) methods immediately and 2 h post-contamination. Efficacy was evaluated for infectious virus, with a subset tested for viral RNA (vRNA) recovery.

Residual antimicrobial coating efficacy against SARS-CoV-2.

Aims: This study evaluated the residual efficacy of commercially available antimicrobial coatings or films against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) on non-porous surfaces.

Methods And Results: Products were applied to stainless steel or ABS plastic coupons and dried overnight. Coupons were inoculated with SARS-CoV-2 in the presence of 5% soil load.

Efficacy of detergent-based cleaning methods against coronavirus MHV-A59 on porous and non-porous surfaces.

This study evaluated the efficacy of detergent-based surface cleaning methods against Murine Hepatitis Virus A59 (MHV) as a surrogate coronavirus for SARS-CoV-2. MHV (5% soil load in culture medium or simulated saliva) was inoculated onto four different high-touch materials [stainless steel (SS), Acrylonitrile Butadiene Styrene plastic (ABS), Formica, seat fabric (SF)]. Immediately and 2-hr post-inoculation, coupons were cleaned (damp wipe wiping) with and without pretreatment with detergent solution or 375 ppm hard water.

Virucidal efficacy of antimicrobial surface coatings against the enveloped bacteriophage Φ6.

Aims: Antimicrobial coatings, for use in combination with routine cleaning and disinfection, were evaluated for their effectiveness in reducing virus concentration on stainless steel surfaces.

Methods: Twenty antimicrobial coating products, predominantly composed of organosilane quaternary ammonium compounds, were applied to stainless steel coupons, dried overnight and evaluated for efficacy against Φ6, an enveloped bacteriophage. Additionally, two peel and stick polymer-based films, a copper-based film and three copper alloys were evaluated.

Effect of inoculation method on the determination of decontamination efficacy against Bacillus spores.

Decontamination studies investigating the effectiveness of products and processes for the inactivation of Bacillus species spores have traditionally utilized metering viable spores in a liquid suspension onto test materials (coupons). The current study addresses the representativeness of studies using this type of inoculation method compared to when coupons are dosed with a metered amount of aerosolized spores. The understanding of this comparability is important in order to assess the representativeness of such laboratory-based testing when deciding upon decontamination options for use against Bacillus anthracis spores.

Bacillus thuringiensis as a surrogate for Bacillus anthracis in aerosol research.

Characterization of candidate surrogate spores prior to experimental use is critical to confirm that the surrogate characteristics are as closely similar as possible to those of the pathogenic agent of interest. This review compares the physical properties inherent to spores of Bacillus anthracis (Ba) and Bacillus thuringiensis (Bt) that impact their movement in air and interaction with surfaces, including size, shape, density, surface morphology, structure and hydrophobicity. Also evaluated is the impact of irradiation on the physical properties of both Bacillus species.

A rapid and repeatable method to deposit bioaerosols on material surfaces.

A simple method for repeatably inoculating surfaces with a precise quantity of aerosolized spores was developed. Laboratory studies were conducted to evaluate the variability of the method within and between experiments, the spatial distribution of spore deposition, the applicability of the method to complex surface types, and the relationship between material surface roughness and spore recoveries. Surface concentrations, as estimated by recoveries from wetted-wipe sampling, were between 5×10(3) and 1.

Development of an aerosol surface inoculation method for bacillus spores.

A method was developed to deposit Bacillus subtilis spores via aerosolization onto various surface materials for biological agent decontamination and detection studies. This new method uses an apparatus coupled with a metered dose inhaler to reproducibly deposit spores onto various surfaces. A metered dose inhaler was loaded with Bacillus subtilis spores, a surrogate for Bacillus anthracis.

Adsorption of chlorine dioxide gas on activated carbons.

Research and field experience with chlorine dioxide (ClO2) gas to decontaminate structures contaminated with Bacillus anthracis spores and other microorganisms have demonstrated the effectiveness of this sterilant technology. However, because of its hazardous properties, the unreacted ClO2, gas must be contained and captured during fumigation events. Although activated carbon has been used during some decontamination events to capture the ClO2 gas, no data are available to quantify the performance of the activated carbon in terms of adsorption capacity and other sorbent property operational features.

Systematic evaluation of the efficacy of chlorine dioxide in decontamination of building interior surfaces contaminated with anthrax spores.

Efficacy of chlorine dioxide (CD) gas generated by two distinct generation systems, Sabre (wet system with gas generated in water) and ClorDiSys (dry system with gas generated in air), was evaluated for inactivation of Bacillus anthracis spores on six building interior surfaces. The six building materials included carpet, acoustic ceiling tile, unpainted cinder block, painted I-beam steel, painted wallboard, and unpainted pinewood. There was no statistically significant difference in the data due to the CD generation technology at a 95% confidence level.

Quantitative method to determine sporicidal decontamination of building surfaces by gaseous fumigants, and issues related to laboratory-scale studies.

Chlorine dioxide gas and vaporous hydrogen peroxide sterilant have been used in the cleanup of building interiors contaminated with spores of Bacillus anthracis. A systematic study, in collaboration with the U.S.

Experimental and modeling study of de novo formation of PCDD/PCDF on MSW fly ash.

The effect of sulfur dioxide (SO2) on the formation of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) has been studied in an entrained-flow reactor (EFR) under simulated waste combustion conditions. A chlorination model based on conditional probability was employed to evaluate the homologue patterns of PCDDs and PCDFs. Results revealed that the presence of SO2 did not alter the formation pathway although SO2 suppressed PCDD/F formation.

Experimental study on the effect of SO2 on PCDD/F emissions: determination of the importance of gas-phase versus solid-phase reactions in PCDD/F formation.

Cofiring coal in municipal solid waste incinerators (MSWls) has previously been reported to reduce polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/Fs) emissions due to increasing the flue gas SO2 concentration. The present study was focused on understanding the primary mechanism responsible for the suppressant effect of SO2 on total PCDD/F formation and toxic equivalent (TEQ) emissions. The addition of SO2, simulating the effect of coal addition on the flue gas composition, resulted in significant reductions in the TEQ emissions due to reactions involving SO2 in the postcombustion zone.

Understanding the role of iron chlorides in the de novo synthesis of polychlorinated dibenzo-p-dioxins/dibenzofurans.

The formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) was investigated for mixtures of carbon black and iron chloride supported on a ceramic glass powder matrix in a low (2%) oxygen environment. Three iron chloride types (iron(II) chloride tetrahydrate, iron(III) chloride hexahydrate, and iron(II) oxychloride) were studied to gain some insights into their role in de novo formation. The importance of iron(II) and iron(III) chlorides both as chlorinating agents and promoters of low-temperature carbon gasification was observed.