Synthesis and Characteristics of Mesoporous Copper Cobalt Oxides Using the Inverse Micelle Method Fabricated for Supercapacitors.

Mesoporous materials have gained considerable attention in the fabrication of supercapacitor electrodes because of their large surface areas and controlled porosities. This study reports the synthesis of mesoporous CuCoO powders using the inverse micelle method. X-ray diffraction, N sorption measurement, transmission electron microscopy, and X-ray photoelectron spectroscopy were performed to investigate the properties of the powders.

Facile surface modification of anion-exchange membranes for improvement of diffusion dialysis performance.

In this study, a facile membrane modification method by spin-coating of pyrrole (Py) monomers dissolved in a volatile solvent followed by an interfacial polymerization is proposed. The surface of a commercial anion-exchange membrane (i.e.

Anion control as a strategy to achieve high-mobility and high-stability oxide thin-film transistors.

Ultra-definition, large-area displays with three-dimensional visual effects represent megatrend in the current/future display industry. On the hardware level, such a "dream" display requires faster pixel switching and higher driving current, which in turn necessitate thin-film transistors (TFTs) with high mobility. Amorphous oxide semiconductors (AOS) such as In-Ga-Zn-O are poised to enable such TFTs, but the trade-off between device performance and stability under illumination critically limits their usability, which is related to the hampered electron-hole recombination caused by the oxygen vacancies.

Preparation of ion exchanger layered electrodes for advanced membrane capacitive deionization (MCDI).

A noble electrode for capacitive deionization (CDI) was prepared by embedding ion exchanger onto the surface of a carbon electrode to practice membrane capacitive deionization (MCDI). Bromomethylated poly (2, 6-dimethyl-1, 4-phenylene oxide) (BPPO) was sprayed on carbon cloth followed by sulfonation and amination to form cation exchange and anion exchange layers, respectively. The ion exchange layers were examined by Scanning electron microscopy (SEM) and Fourier transform infrared spectrometer (FT-IR).

Analyses of interfacial resistances in a membrane-electrode assembly for a proton exchange membrane fuel cell using symmetrical impedance spectroscopy.

Interfacial resistances between the polymer electrolyte membrane (PEM) and catalyst layer (CL) in membrane-electrode assemblies (MEAs) have yet to be systematically examined in spite of its great importance on the fuel cell performance. In order to investigate ionic transport through the PEM/CL interface, the symmetrical impedance mode (SIM) was employed in which the same type of gas was injected (H(2)/H(2)). In this study, the ionic transport resistance at the interface was controlled by the additionally sprayed outer ionomer on the surface of each CL.

Modifying a proton conductive membrane by embedding a "barrier".

For development of proton conductive membranes, it is a difficult dilemma to balance proton conductivity and methanol permeability; however, this research proposes a simple strategy to solve this problem, i.e., embedding a proton conductive "barrier" into the perflorosulfonated matrix.

Investigation on removal of hardness ions by capacitive deionization (CDI) for water softening applications.

Capacitive deionization (CDI) for removal of water hardness was investigated for water softening applications. In order to examine the wettability and pore structure of the activated carbon cloth and composites electrodes, surface morphological and electrochemical characteristics were observed. The highly wettable electrode surface exhibited faster adsorption/desorption of ions in a continuous treatment system.

Hydrogen bonding: a channel for protons to transfer through acid-base pairs.

Different from H(3)O(+) transport as in the vehicle mechanism, protons find another channel to transfer through the poorly hydrophilic interlayers in a hydrated multiphase membrane. This membrane was prepared from poly(phthalazinone ether sulfone kentone) (SPPESK) and H(+)-form perfluorosulfonic resin (FSP), and poorly hydrophilic electrostatically interacted acid-base pairs constitute the interlayer between two hydrophilic phases (FSP and SPPESK). By hydrogen bonds forming and breaking between acid-base pairs and water molecules, protons transport directly through these poorly hydrophilic zones.