Facilitating Uniform Large-Scale MoS, WS Monolayers, and Their Heterostructures through van der Waals Epitaxy.

The fabrication process for the uniform large-scale MoS, WS transition-metal dichalcogenides (TMDCs) monolayers, and their heterostructures has been developed by van der Waals epitaxy (VdWE) through the reaction of MoCl or WCl precursors and the reactive gas HS to form MoS or WS monolayers, respectively. The heterostructures of MoS/WS or WS/MoS can be easily achieved by changing the precursor from WCl to MoCl once the WS monolayer has been fabricated or switching the precursor from MoCl to WCl after the MoS monolayer has been deposited on the substrate. These VdWE-grown MoS, WS monolayers, and their heterostructures have been successfully deposited on Si wafers with 300 nm SiO coating (300 nm SiO/Si), quartz glass, fused silica, and sapphire substrates using the protocol that we have developed.

Ion-driven nanograin formation in early-stage degradation of tri-cation perovskite films.

The operational stability of organic-inorganic halide perovskite based solar cells is a challenge for widespread commercial adoption. The mobility of ionic species is a key contributor to perovskite instability since ion migration can lead to unfavourable changes in the crystal lattice and ultimately destabilisation of the perovskite phase. Here we study the nanoscale early-stage degradation of mixed-halide mixed-cation perovskite films under operation-like conditions using electrical scanning probe microscopy to investigate the formation of surface nanograin defects.

Overcoming Nanoscale Inhomogeneities in Thin-Film Perovskites via Exceptional Post-annealing Grain Growth for Enhanced Photodetection.

Antisolvent-assisted spin coating has been widely used for fabricating metal halide perovskite films with smooth and compact morphology. However, localized nanoscale inhomogeneities exist in these films owing to rapid crystallization, undermining their overall optoelectronic performance. Here, we show that by relaxing the requirement for film smoothness, outstanding film quality can be obtained simply through a post-annealing grain growth process without passivation agents.

Molecular Weight Tuning of Organic Semiconductors for Curved Organic-Inorganic Hybrid X-Ray Detectors.

Curved X-ray detectors have the potential to revolutionize diverse sectors due to benefits such as reduced image distortion and vignetting compared to their planar counterparts. While the use of inorganic semiconductors for curved detectors are restricted by their brittle nature, organic-inorganic hybrid semiconductors which incorporated bismuth oxide nanoparticles in an organic bulk heterojunction consisting of poly(3-hexylthiophene-2,5-diyl) (P3HT) and [6,6]-phenyl C71 butyric acid methyl ester (PC BM) are considered to be more promising in this regard. However, the influence of the P3HT molecular weight on the mechanical stability of curved, thick X-ray detectors remains less well understood.

Enhancing and quantifying spatial homogeneity in monolayer WS.

Controlling the radiative properties of monolayer transition metal dichalcogenides is key to the development of atomically thin optoelectronic devices applicable to a wide range of industries. A common problem for exfoliated materials is the inherent disorder causing spatially varying nonradiative losses and therefore inhomogeneity. Here we demonstrate a five-fold reduction in the spatial inhomogeneity in monolayer WS, resulting in enhanced overall photoluminescence emission and quality of WS flakes, by using an ambient-compatible laser illumination process.

Multi-scale characterisation of a ferroelectric polymer reveals the emergence of a morphological phase transition driven by temperature.

Ferroelectric materials exhibit a phase transition to a paraelectric state driven by temperature - called the Curie transition. In conventional ferroelectrics, the Curie transition is caused by a change in crystal symmetry, while the material itself remains a continuous three-dimensional solid crystal. However, ferroelectric polymers behave differently.

Nanoscale Charge Accumulation and Its Effect on Carrier Dynamics in Tri-cation Perovskite Structures.

Nanoscale investigations by scanning probe microscopy have provided major contributions to the rapid development of organic-inorganic halide perovskites (OIHP) as optoelectronic devices. Further improvement of device level properties requires a deeper understanding of the performance-limiting mechanisms such as ion migration, phase segregation, and their effects on charge extraction both at the nano- and macroscale. Here, we have studied the dynamic electrical response of Cs(FAMA)PbIBr perovskite structures by employing conventional and microsecond time-resolved open-loop Kelvin probe force microscopy (KPFM).

Questioning the Aloe Vera Plant and Apple Memristors.

Non-linear electrical properties of a (biological) tissue can be revealed by non-linear electrical measurements, which means that the applied stimulus itself affects the measurement. If resulting voltage-current plots exhibit pinched hysteresis loops, the underlying tissue may be classified as a memristor, a state dependent resistor. The aloe vera plant and apples have been found to be memristors.

A highly sensitive molecular structural probe applied to in situ biosensing of metabolites using PEDOT:PSS.

A large amount of research within organic biosensors is dominated by organic electrochemical transistors (OECTs) that use conducting polymers such as poly(3,4-ethylene dioxythiophene) doped with poly(styrenesulfonate) (PEDOT:PSS). Despite the recent advances in OECT-based biosensors, the sensing is solely reliant on the amperometric detection of the bioanalytes. This is typically accompanied by large undesirable parasitic electrical signals from the electroactive components in the electrolyte.

Comparing blends and blocks: Synthesis of partially fluorinated diblock polythiophene copolymers to investigate the thermal stability of optical and morphological properties.

The microstructure of the active blend layer has been shown to be a critically important factor in the performance of organic solar devices. Block copolymers provide a potentially interesting avenue for controlling this active layer microstructure in solar cell blends. Here we explore the impact of backbone fluorination in block copolymers of poly(3-octyl-4-fluorothiophene)s and poly(3-octylthiophene) (F-P3OT-b-P3OT).

Precise Characterisation of Molecular Orientation in a Single Crystal Field-Effect Transistor Using Polarised Raman Spectroscopy.

Charge transport in organic semiconductors is strongly dependent on the molecular orientation and packing, such that manipulation of this molecular packing is a proven technique for enhancing the charge mobility in organic transistors. However, quantitative measurements of molecular orientation in micrometre-scale structures are experimentally challenging. Several research groups have suggested polarised Raman spectroscopy as a suitable technique for these measurements and have been able to partially characterise molecular orientations using one or two orientation parameters.

Operational electrochemical stability of thiophene-thiazole copolymers probed by resonant Raman spectroscopy.

We report on the electrochemical stability of hole polarons in three conjugated polymers probed by resonant Raman spectroscopy. The materials considered are all isostructural to poly(3-hexyl)thiophene, where thiazole units have been included to systematically deepen the energy level of the highest occupied molecular orbital (HOMO). We demonstrate that increasing the thiazole content planarizes the main conjugated backbone of the polymer and improves the electrochemical stability in the ground state.

Influence of Backbone Fluorination in Regioregular Poly(3-alkyl-4-fluoro)thiophenes.

We report two strategies toward the synthesis of 3-alkyl-4-fluorothiophenes containing straight (hexyl and octyl) and branched (2-ethylhexyl) alkyl groups. We demonstrate that treatment of the dibrominated monomer with 1 equiv of alkyl Grignard reagent leads to the formation of a single regioisomer as a result of the pronounced directing effect of the fluorine group. Polymerization of the resulting species affords highly regioregular poly(3-alkyl-4-fluoro)thiophenes.

In situ formation of organic-inorganic hybrid nanostructures for photovoltaic applications.

The performance of hybrid (organic-inorganic) photovoltaic devices is critically dependent on the thin film morphology. This work studies the film formation process using the in situ thermal decomposition of a soluble precursor to form a well-distributed network of CdS nanoparticles within a poly(3-hexylthiophene) (P3HT) polymer matrix. Resonant Raman spectroscopy is used to probe the formation of the inorganic nanoparticles and the corresponding changes in the molecular order of the polymer.

Understanding the relationship between molecular order and charge transport properties in conjugated polymer based organic blend photovoltaic devices.

We report a detailed characterization of the thin film morphology of all-polymer blend devices by applying a combined analysis of physical, chemical, optical, and charge transport properties. This is exemplified by considering a model system comprising poly(3-hexylthiophene) (P3HT) and poly(9,9-dioctylfluorene-co-benzothiadiazole) (F8BT). We show that the interactions between the two conjugated polymer components can be controlled by pre-forming the P3HT into highly ordered nanowire structures prior to blending with F8BT, and by varying the molecular weight of the F8BT.

High-crystalline medium-band-gap polymers consisting of benzodithiophene and benzotriazole derivatives for organic photovoltaic cells.

Two semiconducting conjugated polymers were synthesized via Stille polymerization. The structures combined unsubstituted or (triisopropylsilyl)ethynyl (TIPS)-substituted 2,6-bis(trimethylstannyl)benzo[1,2-b:4.5-b']dithiophene (BDT) as a donor unit and benzotriazole with a symmetrically branched alkyl side chain (DTBTz) as an acceptor unit.