Dynamic Assembly of Class II Hydrophobins from at the Air-Water Interface.

Class II hydrophobins are amphiphilic proteins produced by filamentous fungi. One of their typical features is the tendency to accumulate at the interface between an aqueous phase and a hydrophobic phase, such as the air-water interface. The kinetics of the interfacial self-assembly of wild-type hydrophobins HFBI and HFBII and some of their engineered variants at the air-water interface were measured by monitoring the accumulated mass at the interface via nondestructive ellipsometry measurements.

Nanomechanics and Nanorheology of Microgels at Interfaces.

The review addresses nanomechanics and nanorheology of stimuli responsive microgels adsorbed at an interface. In order to measure the mechanical properties on a local scale, an atomic force microscope is used. The tip presents an indenter with a radius of curvature of a few 10 s of nm.

Distribution of CoFeO Nanoparticles Inside PNIPAM-Based Microgels of Different Cross-linker Distributions.

The aim of this study is to tailor the inner structure of positively charged poly-( N-isopropylacrylamid- co-allylamine) (P(NIPAM- co-AA)) microgels for a better control of the distribution of negatively charged magnetic cobaltferrite (CoFeO@CA) nanoparticles (MNPs) within the microgels. Therefore, two different strategies are followed for the microgel synthesis: the (one pot) batch method which leads to a higher cross-linker density in the microgel core and the feeding method which compensates different reaction kinetics of the cross-linker and the monomers. The latter one is expected to result in a homogeneous cross-linker distribution.

Combined Cononsolvency and Temperature Effects on Adsorbed PNIPAM Microgels.

The present study addresses the multiresponsive behavior of poly(N-isopropylacrylamide) (PNIPAM) microgels adsorbed to interfaces. The microgels react to changes in temperature by shrinking in aqueous solution above their volume phase transition temperature (VPTT). Additionally, they shrink in mixtures of water and ethanol, although both individual liquids are good solvents for PNIPAM.

Poly(-isopropylacrylamide) Microgels under Alcoholic Intoxication: When a LCST Polymer Shows Swelling with Increasing Temperature.

Poly(-isopropylacrylamide) (PNIPAM) microgel is a smart polymer that shows a volume phase transition temperature (VPTT) at around 32 °C in aqueous solutions, above which it collapses. In this work, combining experiments and molecular simulations, it is shown that PNIPAM microgels do not always exhibit a collapsed structure above the VPTT. Instead, PNIPAM in aqueous alcohol mixtures shows a two-step conformational transition, i.

Construction of Compact Polyelectrolyte Multilayers Inspired by Marine Mussel: Effects of Salt Concentration and pH As Observed by QCM-D and AFM.

Biomimetic multilayers based on layer-by-layer (LbL) assembly were prepared as functional films with compact structure by incorporating the mussel-inspired catechol cross-linking. Dopamine-modified poly(acrylic acid) (PAADopa) was synthesized as a polyanion to offer electrostatic interaction with the prelayer polyethylenimine (PEI) and consecutively cross-linked by zinc to generate compact multilayers with tunable physicochemical properties. In situ layer-by-layer growth and cross-linking were monitored by a quartz crystal microbalance with dissipation (QCM-D) to reveal the kinetics of the process and the influence of Dopa chemistry.

Loading of PNIPAM Based Microgels with CoFe2O4 Nanoparticles and Their Magnetic Response in Bulk and at Surfaces.

The present paper addresses the loading of thermoresponsive poly-N-isopropylacrylamide (PNIPAM) based microgel particles with magnetic nanoparticles (MNP: CoFe2O4@PAA (PAA = poly(acrylic acid))) and their response to an external magnetic field. The MNP uptake is analyzed by transmission electron microscopy (TEM). Obviously, the charge combination of MNP and microgels plays an important role for the MNP uptake, but it does not explain the whole uptake process.

Nanofluidics of thin polymer films: linking the slip boundary condition at solid-liquid interfaces to macroscopic pattern formation and microscopic interfacial properties.

If a thin liquid film is not stable, different rupture mechanisms can be observed causing characteristic film morphologies: spinodal dewetting and dewetting by nucleation of holes. This rupturing entails liquid flow and opens new possibilities to study microscopic phenomena. Here we use this process of dewetting to gain insight on the slip boundary condition at the solid-liquid interface.