The mechanical properties of polymeric membranes are very important in water treatment applications. In this study, polysulfone (PSF) membranes with different loadings of cellulose nanofibers (CNFs) were prepared via the phase inversion method. CNF was characterized through transmission electron microscopy (TEM) and scanning electron microscopy (SEM).
View Article and Find Full Text PDFPorous polymer-based nanocomposites have been used for various applications due to their advantages, including multi-functionalities, easy and known manufacturability, and low cost. Understanding of their mechanical properties has become essential to expand the nanocomposites' applications and efficiency, including service-life, resistance to different loads, and reliability. In this review paper, the focus is on the modeling of the mechanical properties of porous polymer-based nanocomposites, including the effects of loading rates, operational temperatures, and the material's porosity.
View Article and Find Full Text PDFAlthough it is still a great challenge, developing oil-/water-separating membranes that combine the advantages of high separation efficiency, salty environments tolerance, and fouling resistance are highly demanded for marine oil spill cleanups and oil-/gas-produced water treatment. Here, we report a new type of all-inorganic nanostructured membrane, which is composed of titanate nanofibers and SiO particulate gel for efficient and stable oil/saltwater separation. The nanoporous and interconnected network structure constructed with titanate nanofibers is the key to ensure the high separation efficiency and high water flux of the new membrane.
View Article and Find Full Text PDFMembranes (Basel)
December 2019
In the present study, nanocomposite ultrafiltration membranes were prepared by incorporating nanotubes clay halloysite (HNTs) into polysulfone (PSF) and PSF/polyvinylpyrrolidone (PVP) dope solutions followed by membrane casting using phase inversion method. Characterization of HNTs were conducted using scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and thermogravimetric (TGA) analysis. The pore structure, morphology, hydrophilicity and mechanical properties of the composite membranes were characterized by using SEM, water contact angle (WCA) measurements, and dynamic mechanical analysis.
View Article and Find Full Text PDFShort-fiber-reinforced thermoplastics are popular for improving the mechanical properties exhibited by pristine thermoplastic materials. Due to the inherent conflict between strength and ductility, there are only a few successful cases of simultaneous enhancement of these two properties in polymer composite components. The objective of this work was to explore the feasibility of simultaneous enhancement of strength and ductility in ABS-based composites with short-carbon and Kevlar fiber reinforcement by material extrusion 3D printing (ME3DP).
View Article and Find Full Text PDFThe effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP)-based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles, including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9, and 12.
View Article and Find Full Text PDFExcess phosphate in water is known to cause eutrophication, and its removal is imperative. Nanoclay minerals are widely used in environmental remediation due to their low-cost, adequate availability, environmental compatibility, and adsorption efficiency. However, the removal of anions with nanoclays is not very effective because of electrostatic repulsion from clay surfaces with a net negative charge.
View Article and Find Full Text PDFThere is strong interest in windable and stretchable membranes to meet the technological demands of practical water treatments. Oil/water separating membranes of this type is still significantly underdeveloped. Here, we reported a windable and stretchable membrane with three-dimensional structure for efficient oil/water separation.
View Article and Find Full Text PDFJ Phys Condens Matter
September 2016
Recently, the transition metal dichalcogenides have attracted renewed attention due to the potential use of their low-dimensional forms in both nano- and opto-electronics. In such applications, the electronic and transport properties of monolayer transition metal dichalcogenides play a pivotal role. The present paper provides a new insight into these essential properties by studying the complex band structures of popular transition metal dichalcogenide monolayers (MX 2, where M = Mo, W; X = S, Se, Te) while including spin-orbit coupling effects.
View Article and Find Full Text PDFThe assessment of the three-dimensional architecture of collagen fibers inside vessel walls constitutes one of the bases for building structural models for the description of the mechanical behavior of these tissues. Multiphoton microscopy allows for such observations, but is limited to volumes of around a thousand of microns. In the present work, we propose to observe the collagenous network of vascular tissues using micro-CT.
View Article and Find Full Text PDFThe collagen fibers' three-dimensional architecture has a strong influence on the mechanical behavior of biological tissues. To accurately model this behavior, it is necessary to get some knowledge about the structure of the collagen network. In the present paper, we focus on the in situ characterization of the collagenous structure, which is present in porcine jugular vein walls.
View Article and Find Full Text PDFIn this paper the mechanical response of the arthropod cuticle is evaluated by means of a multiscale approach including interface effects. The cuticle's elastic behavior is modeled at the nano and the micro scales by mean-field homogenization techniques. With respect to the work of Nikolov et al.
View Article and Find Full Text PDFJ Mech Behav Biomed Mater
July 2013
The purpose of the present work is to propose a new multiscale model for the prediction of the mechanical behavior of vein walls. This model is based on one of our previous works which considered scale transitions applied to undulated collagen fibers. In the present work, the scale below was added to take the anisotropy of collagen fibrils into account.
View Article and Find Full Text PDFClin Orthop Relat Res
August 2011
Background: Crosslinked UHMWPE as a bearing surface in total joint arthroplasty has higher wear resistance than conventional UHMWPE but lower strength and toughness. To produce crosslinked UHMWPE with improved mechanical properties, the material can be treated before crosslinking by tension to induce molecular alignment (texture).
Questions/purposes: We asked how (1) the microstructure of UHMWPE evolves when subjected to tension and (2) whether the new microstructure (texture) increases strength and toughness.
The aim of this work was to predict the effective elastic properties of starch-based nano-biocomposites. Experiments (materials elaboration, morphological characterization and determination of mechanical properties) were conducted on both the pristine matrix (plasticized starch) and the matrix filled with montmorillonite nanoclay. Aggregated/intercalated and exfoliated nano-biocomposites were produced and mechanically tested under uniaxial tension to understand the effect of montmorillonite morphology/dispersion on the stiffness properties of starch-based nano-biocomposites.
View Article and Find Full Text PDF