Complex Resonant Scattering Behavior in the Surface Plasmon Resonance Imaging Microscopy of Single Gold Nanorods.

Diffraction patterns observed in surface plasmon resonance imaging (SPRI) microscopy measurements of single gold nanorods (AuNRs) exhibit a complex behavior at wavelengths near the longitudinal plasmonic resonance band. SPRI microscopy measurements at 814 nm from AuNRs in three samples with resonance extinction maxima at 670, 816, and 980 nm reveal a variety of diffraction patterns with central peaks that are either positive, negative, or biphasic. A unitless ratio parameter (-1 ≤ ≤ 1) is created to describe the distribution of diffraction patterns.

Effects of radiation and MediPort placement on the development of thoracic outlet syndrome.

We present a patient who exemplifies the interplay of factors contributing to the development of venous-type thoracic outlet syndrome. The patient was treated with both radiation and chemotherapy for squamous cell carcinoma in the head and neck region; radiation and chemotherapy have been known to damage the vascular system. Multimodality treatment is necessary to achieve good long-term results in these complex patients.

Endovascular stenting of supra-aortic lesions using a transcarotid retrograde approach and flow reversal: A multicenter case series.

Objective: Endovascular treatment has largely replaced open reconstruction of proximal brachiocephalic and left common carotid ostial arterial stenoses. The objective of this study was to report the technical feasibility and safety of a flow-based embolic protection system in stenting of single and tandem stenotic lesions of supra-aortic arch vessels.

Methods: All cases used flow-based neuroprotection by the ENROUTE Transcarotid Neuroprotection System (Silk Road Medical, Sunnyvale, Calif).

MicroRNA detection on microsensor arrays by SPR imaging measurements with enzymatic signal enhancement.

We investigated sequence-specific and simultaneous microRNA (miRNA) detections by surface plasmon resonance (SPR) imaging measurements on SPR chips possessing an Au spot array modified with probe DNAs based on a miRNA-detection-selective SPR signal amplification method. MiRNAs were detected with the detection limit of the attomole level by SPR imaging measurements for different miRNA concentrations on a single chip. SPR signals were enhanced based on a combination process of sequence-specific hybridization of the miRNA to the probe DNAs, extension reaction of polyadenine (poly(A)) tails by poly(A) polymerase, binding of a ternary complex of T-biotin/horseradish peroxidase (HRP)-biotin/streptavidin to the poly(A) tails, and the oxidation reaction of tetramethylbenzidine (TMB) on the HRP by providing a blue precipitate on the surface.

Effectiveness of treatment of innominate artery stenosis with retrograde supra-aortic stent using a flow reversal stent system.

We present the case of a 71-year-old man with critical stenosis of the innominate artery after previously undergoing bilateral carotid artery endarterectomies. We used an open retrograde approach of the right carotid artery to stent the innominate artery lesion employing the new ENROUTE Transcarotid Stent System with flow reversal.

Particle sensing with confined optical field enhanced fluorescence emission (Cofefe).

We describe the development and performance of a new type of optical sensor suitable for registering the binding/dissociation of nanoscopic particles near a gold sensing surface. The method shares similarities with surface plasmon resonance microscopy but uses a completely different optical signature for reading out binding events. This new optical read-out mechanism, which we call confined optical field enhanced fluorescence emission (Cofefe), uses pulsed surface plasmon polariton fields at the gold/liquid interface that give rise to confined optical fields upon binding of the target particle to the gold surface.

A Microwell-Printing Fabrication Strategy for the On-Chip Templated Biosynthesis of Protein Microarrays for Surface Plasmon Resonance Imaging.

A two-step templated, ribosomal biosynthesis/printing method for the fabrication of protein microarrays for surface plasmon resonance imaging (SPRI) measurements is demonstrated. In the first step, a sixteen component microarray of proteins is created in microwells by cell free on chip protein synthesis; each microwell contains both an transcription and translation (IVTT) solution and 350 femtomoles of a specific DNA template sequence that together are used to create approximately 40 picomoles of a specific hexahistidine-tagged protein. In the second step, the protein microwell array is used to contact print one or more protein microarrays onto nitrilotriacetic acid (NTA)-functionalized gold thin film SPRI chips for real-time SPRI surface bioaffinity adsorption measurements.

Characterizing Single Polymeric and Protein Nanoparticles with Surface Plasmon Resonance Imaging Measurements.

Near-infrared surface plasmon resonance imaging (SPRI) microscopy is used to detect and characterize the adsorption of single polymeric and protein nanoparticles (PPNPs) onto chemically modified gold thin films in real time. The single-nanoparticle SPRI responses, Δ%R, from several hundred adsorbed nanoparticles are collected in a single SPRI adsorption measurement. Analysis of Δ%R frequency distribution histograms is used to provide information on the size, material content, and interparticle interactions of the PPNPs.

Fabrication of PEDOT Nanocone Arrays with Electrochemically Modulated Broadband Antireflective Properties.

Ordered nanocone arrays of the electroactive polymer poly(3,4-ethylenedioxythiophene) (PEDOT) were fabricated by the simultaneous oxygen plasma etching of an electrodeposited PEDOT thin film coated with a hexagonally closed packed polystyrene bead monolayer. PEDOT nanocone arrays with an intercone spacing of 200 nm and an average nanocone height of 350 nm exhibited a low broadband reflectivity of <1.5% from 550 to 800 nm.

Measuring melittin uptake into hydrogel nanoparticles with near-infrared single nanoparticle surface plasmon resonance microscopy.

This paper describes how changes in the refractive index of single hydrogel nanoparticles (HNPs) detected with near-infrared surface plasmon resonance microscopy (SPRM) can be used to monitor the uptake of therapeutic compounds for potential drug delivery applications. As a first example, SPRM is used to measure the specific uptake of the bioactive peptide melittin into N-isopropylacrylamide (NIPAm)-based HNPs. Point diffraction patterns in sequential real-time SPRM differential reflectivity images are counted to create digital adsorption binding curves of single 220 nm HNPs from picomolar nanoparticle solutions onto hydrophobic alkanethiol-modified gold surfaces.

Surface Enzyme Chemistries for Ultrasensitive Microarray Biosensing with SPR Imaging.

The sensitivity and selectivity of surface plasmon resonance imaging (SPRI) biosensing with nucleic acid microarrays can be greatly enhanced by exploiting various nucleic acid ligases, nucleases, and polymerases that manipulate the surface-bound DNA and RNA. We describe here various examples from each of these different classes of surface enzyme chemistries that have been incorporated into novel detection strategies that either drastically enhance the sensitivity of or create uniquely selective methods for the SPRI biosensing of proteins and nucleic acids. A dual-element generator-detector microarray approach that couples a bioaffinity adsorption event on one microarray element to nanoparticle-enhanced SPRI measurements of nucleic acid hybridization adsorption on a different microarray element is used to quantitatively detect DNA, RNA, and proteins at femtomolar concentrations.

Lithographically Patterned Nanoscale Electrodeposition of Plasmonic, Bimetallic, Semiconductor, Magnetic, and Polymer Nanoring Arrays.

Large area arrays of magnetic, semiconducting, and insulating nanorings were created by coupling colloidal lithography with nanoscale electrodeposition. This versatile nanoscale fabrication process allows for the independent tuning of the spacing, diameter, and width of the nanorings with typical values of 1.0 μm, 750 nm, and 100 nm, respectively, and was used to form nanorings from a host of materials: Ni, Co, bimetallic Ni/Au, CdSe, and polydopamine.

Shrink-induced silica multiscale structures for enhanced fluorescence from DNA microarrays.

We describe a manufacturable and scalable method for fabrication of multiscale wrinkled silica (SiO2) structures on shrink-wrap film to enhance fluorescence signals in DNA fluorescence microarrays. We are able to enhance the fluorescence signal of hybridized DNA by more than 120 fold relative to a planar glass slide. Notably, our substrate has improved detection sensitivity (280 pM) relative to planar glass slide (11 nM).

Flexible Teflon nanocone array surfaces with tunable superhydrophobicity for self-cleaning and aqueous droplet patterning.

Tunable hydrophobic/hydrophilic flexible Teflon nanocone array surfaces were fabricated over large areas (cm(2)) by a simple two-step method involving the oxygen plasma etching of a colloidal monolayer of polystyrene beads on a Teflon film. The wettability of the nanocone array surfaces was controlled by the nanocone array dimensions and various additional surface modifications. The resultant Teflon nanocone array surfaces were hydrophobic and adhesive (a "gecko" type of surface on which a water droplet has a high contact angle but stays in place) with a contact angle that correlated with the aspect ratio/sharpness of the nanocones.

Silica nanowire arrays for diffraction-based bioaffinity sensing.

Arrays of electrodeposited silica nanowires (SiO2 NWs) have been fabricated over large areas (cm(2)) on fluoropolymer thin films attached to glass substrates by a combination of photolithography and electrochemically triggered sol-gel nanoscale deposition. Optical and scanning electron microscopy (SEM) measurements revealed that the SiO2 NW arrays had an average spacing of ten micrometers and an average width of 700 nm with a significant grain structure that was a result of the sol-gel deposition process. The optical diffraction properties at 633 nm of the SiO2 NW arrays were characterized when placed in contact with solutions by using a prism-coupled total internal reflection geometry; quantification of changes in these diffraction properties was applied in various sensing applications.

Single-nanoparticle near-infrared surface plasmon resonance microscopy for real-time measurements of DNA hybridization adsorption.

A novel 814 nm near-infrared surface plasmon resonance (SPR) microscope is used for the real-time detection of the sequence-selective hybridization adsorption of single DNA-functionalized gold nanoparticles. The objective-coupled, high numerical aperture SPR microscope is capable of imaging in situ the adsorption of single polystyrene and gold particles with diameters ranging from 450 to 20 nm onto a 90 μm × 70 μm area of a gold thin film with a time resolution of approximately 1-3 s. Initial real-time SPR imaging (SPRI) measurements were performed to detect the accumulation of 40 nm gold nanoparticles for 10 min onto a gold thin film functionalized with a 100% complementary DNA surface at concentrations from 5 pM to 100 fM by counting individual particle binding events.

Fabrication of broadband antireflective plasmonic gold nanocone arrays on flexible polymer films.

Flexible broadband antireflective and light-absorbing nanostructured gold thin films are fabricated by gold vapor deposition onto Teflon films modified with nanocone arrays. The nanostructures are created by the oxygen plasma etching of polystyrene bead monolayers on Teflon surfaces. The periodicity and height of the nanocone arrays are controlled by the bead diameter and the overall etching time.

Electrodeposition of polydopamine thin films for DNA patterning and microarrays.

The controlled electrodeposition of functional polydopamine (PDA) thin films from aqueous dopamine solutions is demonstrated with a combination of electrochemistry, atomic force microscopy (AFM), and surface plasmon resonance (SPR) measurements. PDA micropatterns are then fabricated by electrodeposition on micrometer length scale gold electrodes and used for attaching amino-modified single-stranded DNA (ssDNA). After hybridization with fluorescently labeled ssDNA, the fluorescence microscopy characterization reveals that: (i) PDA can be toposelectively deposited at the microscale and (ii) electrochemically deposited PDA can be functionalized with amino-terminated ssDNA using the same chemistry as that for spontaneously deposited PDA.

Fabrication of DNA microarrays on polydopamine-modified gold thin films for SPR imaging measurements.

Polydopamine (PDA) films were fabricated on thin film gold substrates in a single-step polymerization-deposition process from dopamine solutions and then employed in the construction of robust DNA microarrays for the ultrasensitive detection of biomolecules with nanoparticle-enhanced surface plasmon resonance (SPR) imaging. PDA multilayers with thicknesses varying from 1 to 5 nm were characterized with a combination of scanning angle SPR and AFM experiments, and 1.3 ± 0.

Entrapment of bed bugs by leaf trichomes inspires microfabrication of biomimetic surfaces.

Resurgence in bed bug infestations and widespread pesticide resistance have greatly renewed interest in the development of more sustainable, environmentally friendly methods to manage bed bugs. Historically, in Eastern Europe, bed bugs were entrapped by leaves from bean plants, which were then destroyed; this purely physical entrapment was related to microscopic hooked hairs (trichomes) on the leaf surfaces. Using scanning electron microscopy and videography, we documented the capture mechanism: the physical impaling of bed bug feet (tarsi) by these trichomes.

DNAzyme footprinting: detecting protein-aptamer complexation on surfaces by blocking DNAzyme cleavage activity.

A novel method to quantitatively measure the binding of proteins to single-stranded DNA (ssDNA) aptamers that employs the inhibition of the DNAzyme hydrolysis of aptamer monolayers is described. A 28-base DNAzyme was designed to specifically bind to and cleave a 29-base ssDNA sequence that can fold into a G-quartet aptamer and bind the protein thrombin. The binding strength of the DNAzyme to the aptamer sequence was designed to be less than the binding strength of the thrombin to the aptamer (ΔG° = -43.

Lithographically patterned electrodeposition of gold, silver, and nickel nanoring arrays with widely tunable near-infrared plasmonic resonances.

A novel low-cost nanoring array fabrication method that combines the process of lithographically patterned nanoscale electrodeposition (LPNE) with colloidal lithography is described. Nanoring array fabrication was accomplished in three steps: (i) a thin (70 nm) sacrificial nickel or silver film was first vapor-deposited onto a plasma-etched packed colloidal monolayer; (ii) the polymer colloids were removed from the surface, a thin film of positive photoresist was applied, and a backside exposure of the photoresist was used to create a nanohole electrode array; (iii) this array of nanoscale cylindrical electrodes was then used for the electrodeposition of gold, silver, or nickel nanorings. Removal of the photoresist and sacrificial metal film yielded a nanoring array in which all of the nanoring dimensions were set independently: the inter-ring spacing was fixed by the colloidal radius, the radius of the nanorings was controlled by the plasma etching process, and the width of the nanorings was controlled by the electrodeposition process.

Self-Assembly of Flux-Closure Polygons from Magnetite Nanocubes.

Well-defined nanoscale flux-closure polygons (nanogons) have been fabricated on hydrophilic surfaces from the face-to-face self-assembly of magnetite nanocubes. Uniform ferrimagnetic magnetite nanocubes (∼86 nm) were synthesized and characterized with a combination of electron microscopy, diffraction, and magnetization measurements. The nanocubes were subsequently cast onto hydrophilic substrates, wherein the cubes lined up face-to-face and formed a variety of polygons due to magnetostatic and hydrophobic interactions.

On-chip synthesis of protein microarrays from DNA microarrays via coupled in vitro transcription and translation for surface plasmon resonance imaging biosensor applications.

Protein microarrays are fabricated from double-stranded DNA (dsDNA) microarrays by a one-step, multiplexed enzymatic synthesis in an on-chip microfluidic format and then employed for antibody biosensing measurements with surface plasmon resonance imaging (SPRI). A microarray of dsDNA elements (denoted as generator elements) that encode either a His-tagged green fluorescent protein (GFP) or a His-tagged luciferase protein is utilized to create multiple copies of mRNA (mRNA) in a surface RNA polymerase reaction; the mRNA transcripts are then translated into proteins by cell-free protein synthesis in a microfluidic format. The His-tagged proteins diffuse to adjacent Cu(II)-NTA microarray elements (denoted as detector elements) and are specifically adsorbed.

Wide-field, surface-sensitive four-wave mixing microscopy of nanostructures.

We describe a wide-field four-wave mixing (FWM) microscope with imaging characteristics optimized for examining nanostructures. The microscope employs surface-plasmon polariton (SPP) excitation in a gold film to achieve surface-sensitive imaging conditions. The SPP surface fields boost the FWM efficiency by 2 orders of magnitude relative to the excitation efficiency of the evanescent fields at a bare glass surface.