Characterization of 3D printed composite for final dental restorations.

Objectives: This study evaluated the mechanical, optical, microstructural, surface, and adhesive behavior of a 3D printing resin comparing it with a machinable resin composite.

Materials And Methods: Specimens of different sizes and shapes were either printed (Vitality, Smart Dent) or machinable (Grandio Blocs, Voco GmbH) resin composites with similar composition were prepared. Surface and mechanical characterization were performed with Knoop hardness, flexural strength (three-point-bending), and elastic modulus tests.

Effect of cementation protocols on the fracture load of bilayer ceramic crowns manufactured by the Rapid Layer Technology.

To evaluate the fracture load of bilayer ceramic crowns manufactured by Rapid Layer Technology (RLT) after different cementation protocols of the veneering ceramic to the zirconia infrastructures. Sixty epoxy resin preparations simulating a molar tooth were obtained and 60 zirconia infrastructures and feldspathic crowns were manufactured by RLT and divided into 6 groups according to the cementation protocol at the interface to veneering ceramic (n=10): Ctr- control: conventional resin cement; Al- Al2O3 sandblasting 50µm + conventional resin cement; Al/MDP- Al2O3 sandblasting (50µm) + resin cement with MDP; Sil- silicatization 30µm + conventional resin cement; Gl/HF- glaze + hydrofluoridric acid (5%,60s) + silane + conventional resin cement; Gl- glazing as bonding agent. The feldspathic ceramic internal surface was etched with fluoridric acid (5%) + silane followed by cementation according to respective protocols.

Isolation and genetic characterization of from chickens from public markets in Pernambuco State, Brazil.

This study aimed to evaluate the presence and viability of in chickens intended for human consumption in the Pernambuco State, Brazil. Blood and tissue samples were collected from 25 chickens sold in markets in Recife, Pernambuco. Samples were evaluated by indirect immunofluorescence assay (IFA) to detect antibodies to .

Fatigue and failure mode analyses of glass infiltrated 5Y-PSZ bonded onto dentin analogues.

The purpose of this study was to evaluate the fatigue survival of 5Y-PSZ zirconia infiltrated with an experimental glass and bonded onto dentin analogues. Disc-shaped specimens of a 5Y-PSZ (Katana UTML Kuraray Noritake) were cemented onto dentin analogs (NEMA G10) and divided into four groups (n = 15): Zctrl Group (control, without infiltration); Zglz Group (Glaze, compression surface); Zinf-comp Group (Experimental Glass, compression surface); Zinf-tens Group (Experimental Glass, tension surface). Surface treatments were varied.

Influence of leptin and its receptors on individuals under chronic social stress behavior.

Stress is the body's physiological reaction to a dangerous or threatening situation, leading to a state of alertness. This reaction is necessary for developing an effective adaptive response to stress and maintaining the body's homeostasis. Chronic stress, caused mainly by social stress, is what primarily affects the world's population.

Borosilicate glass as a surface finishing alternative for improving the mechanical properties of third-generation zirconia.

Objective: This study evaluated the effect of an experimental borosilicate glass on the mechanical and optical behavior of 5Y-PSZ zirconia and comparing it to commercial glaze and as-sintered.

Methods: Disc-shaped specimens of a 5Y-PSZ (Zpex Smile) were prepared and sintered (1550 °C, 2 h). The zirconia discs were randomly divided according to the surface treatment: as-sintered (C), commercial glaze (G), and experimental borosilicate glass (SL).

Comparison of molecular techniques for the detection of Toxoplasma gondii in raw bovine milk from small rural properties in Brazil.

This study aimed to research Toxoplasma gondii DNA in 102 samples of raw bovine milk from expansion tanks, in small properties located in different cities of the Midwest region of São Paulo, Brazil. For this, polymerase chain reaction (PCR) was performed with the primers TOX4/TOX5 for cPCR (conventional PCR), TgNP1/TgNP2 gene for nested PCR and the Tg18s58F/Tg18s348R for nested PCR. It was possible to detect T.

Promoting Bird Functional Diversity on Landscapes with a Matrix of Planted Eucalyptus spp. in the Atlantic Forest.

Promoting the diversity of biological communities in areas of agricultural production is a very current debate since protected areas may not be sufficient to ensure biodiversity conservation. Among the biological communities affected by the production areas are birds, which show rapid responses to changes in the landscape. Here we seek to understand how landscape planning, concerning its composition and configuration, in areas with a matrix of planted Eucalyptus spp.

Preheated Composite as an Alternative for Bonding Feldspathic and Hybrid Ceramics: A Microshear Bond Strength Study.

Purpose: To evaluate the bond strength between alternative or conventional luting agents and indirect restorative materials.

Materials And Methods: Blocks of a polymer-infiltrated ceramic network (PICN, Vita Enamic) and a feldspathic ceramic (FEL, Vita Mark II) were sliced and divided according to the luting agent: resin cement (PICN-RC, FEL-RC), flowable composite (PICN-FC, FEL-FC), or preheated composite (PICN-PH, FEL-PH). The ceramic surfaces were polished, etched with 5% hydrofluoric acid for 60 s, and then a silane layer was applied.

Fatigue behavior of multilayer ceramic structures in traditional and reverse layering designs.

Purpose: This study evaluated the fatigue failure load (FFL) and the number of cycles for fatigue failure (CFF) of traditional (porcelain layer up) and reversed (zirconia layer up) designs of porcelain-veneered zirconia samples prepared with heat-pressing or file-splitting techniques.

Materials And Methods: Zirconia discs were prepared and veneered with heat-pressed or machined feldspathic ceramic. The bilayer discs were bonded onto a dentin-analog according to the bilayer technique and sample design: traditional heat-pressing (T-HP), reversed heat-pressing (R-HP), traditional file-splitting with fusion ceramic (T-FC), reversed file-splitting with fusion ceramic R-FC), traditional file-splitting with resin cement (T-RC), and reversed file-splitting with resin cement (R-RC).

Occurrence of Apicomplexa protozoa in wild birds in the Northeast region of Brazil.

Protozoa of the Apicomplexa phylum are worldwide distributed with capacity to infect endothermic animals. The study of these protozoa in wild birds in Brazil is scarce. This study aimed to evaluate the occurrence of apicomplexan protozoa in wild birds in the Northeast of Brazil.

Herd and animal level prevalences and risk factors for Neospora caninum infection in cattle in the state of Paraíba, northeastern Brazil.

Bovine neosporosis is a globally important disease, causing abortions and significant economic losses. In Brazil, studies on neosporosis in cattle are few and based on limited samples and/or from limited areas. We aimed to determine the herd and animal levels seroprevalence and associated factors for Neospora caninum infections in cattle from the state of Paraíba, Northeastern Brazil, using a planned sampling.

Occurrence of extended-spectrum β-lactamase-producing Enterobacteriaceae in raw milk from cows with subclinical mastitis in northeast Brazil.

Extended-spectrum β-lactamase (ESBL)-producing Gram negative bacteria are becoming increasingly important in veterinary and human medicine because they can hydrolyze the third generation β-lactams, penicillins, and monobactams. The aim of this study was to identify ESBL-producing Enterobacteriaceae in raw cow milk samples from northeast Brazil. Twenty-six bacterial isolates belonging to the Enterobacteriaceae family were obtained from milk samples from 257 cows with subclinical mastitis.

Endocrown restorations in premolars: influence of remaining axial walls of tooth structure and restorative materials on fatigue resistance.

Objectives: To evaluate the effect of the remaining tooth structure and different CAD/CAM materials on the fatigue performance and failure mode of endodontically treated premolars restored with endocrowns.

Materials And Methods: Ninety maxillary premolars were endodontically treated and assigned into 6 groups (n = 15) according to the number of remaining axial walls (four, three, and two) and restorative materials (ultra-translucent zirconia 5Y-PSZ [KATANA UTML] and lithium disilicate [IPS e.max-CAD]).

High-Translucency Zirconia Following Chemical Vapor Deposition with SiH4: Evidence of Surface Modifications and Improved Bonding.

Purpose: To evaluate the effect of plasma-enhanced chemical vapor deposition (PECVD) with silicon hydride (SiH4) at different times on HT-zirconia surface characteristics and bonding of composite cement before and after thermocycling.

Materials And Methods: Blocks of HT zirconia were obtained, polished, sintered and divided into five groups, according to PECVD time (n = 31): Zr-30 (30 s), Zr-60 (60 s), Zr-120 (120 s) and Zr-300 (300 s). The control group (Zr-0) did not receive PECVD.

Effect of resin cement elastic modulus on the biaxial flexural strength and structural reliability of an ultra-thin lithium disilicate glass-ceramic material.

Objectives: Photo- and dual-polymerized resin-based luting agent was evaluated for elastic moduli effects on ultra-thin lithium disilicate (LD) glass-ceramic strengthening, structural reliability, and stress distribution.

Materials And Methods: One hundred-sixty LD discs (IPS e.max CAD, Ivoclar/Vivadent) were produced in ultra-thin thicknesses (half with 0.

Effect of Resin Cement at Different Thicknesses on the Fatigue Shear Bond Strength to Leucite Ceramic.

Objectives:  This study was performed to evaluate fatigue survival by shear test in the union of leucite-reinforced feldspathic ceramic using different cement thicknesses.

Materials And Methods:  Leucite-reinforced glass ceramics blocks were sectioned in 2-mm thick slices where resin cylinders were cemented. The samples were distributed in two experimental groups ( = 20) according to the cement thickness (60 and 300 μm).

Silica infiltration on translucent zirconia restorations: Effects on the antagonist wear and survivability.

Objective: To assess potential antagonist wear and survival probability of silica-infiltrated zirconia compared to glass-graded, glazed, and polished zirconia.

Methods: Table top restorations made of 3Y-TZP (3Y), 5Y-PSZ (5Y), and lithium disilicate (LD) were bonded onto epoxy resin preparations. Each zirconia was divided into five groups according to the surface treatment: polishing; glaze; polishing-glaze; glass infiltration; and silica infiltration.

Detection of Anti- IgG in Blood Serum and Colostrum Samples in Naturally Infected Sheep and in Their Newborn Offspring.

The aim was to detect correlations of IgG antibodies against in serum and colostrum samples from ewes, through the IFAT, and to evaluate the presence of this immunoglobulin in the serum of newborn lambs after colostrum ingestion. Blood samples from 162 ewes that did not show any disease in the general physical examination and from their newborn lambs, not more than five days postpartum, along with 162 colostrum samples and 182 blood samples from the neonates, were analyzed. In total, 27.

Determinants of COVID-19 Vaccine Acceptance among Dental Professionals: A Multi-Country Survey.

Purpose: This study sought to investigate the acceptance rate and associated factors of COVID-19 vaccines among dentists and dental students in seven countries.

Material And Methods: A structured questionnaire prepared and guided by the report of the SAGE Working Group on Vaccine Hesitancy was distributed among groups of dentists and dental students in seven countries across four continents.

Results: A total of 1527 subjects (850 dentists and 677 dental students) participated in this survey.

Effect of Porcelain-to-Zirconia Ratio and Bonding Strategy on the Biaxial Flexural Strength and Weibull Characteristics of a Stress-Free Bilayer CAD/CAM Ceramic System.

Purpose: To evaluate the biaxial flexural strength of different porcelain-to-zirconia thickness ratios and bonding strategies of a stress-free bilayer CAD/CAM ceramic system.

Materials And Methods: A total of 60 zirconia discs (diameter: 15 mm; thickness: 0.3 or 0.