Post-fatigue fracture load, stress concentration and mechanical properties of feldspathic, leucite- and lithium disilicate-reinforced glass ceramics.

Objective: To evaluate the mechanical properties of different CAD/CAM ceramic systems and the post-fatigue fracture and stress distribution when used as cemented crowns.

Materials And Methods: Sixty (60) CAD/CAM monolithic crowns were milled using three different ceramic materials (FD - Feldspathic [Vita Mark II]), LE - Leucite-based ceramic [IPS Empress CAD] and LD - Lithium Disilicate [IPS e.max CAD]) and adhesively cemented on resin composite dyes.

[Not Available].

Thisstudy aimed to evaluate the effect of the electric current direction application on the resin composite-dentin bond strength using three adhesive systems. Human molar teeth were distributed according to the adhesive system (two-step self-etch - Clearfil SE Bond, Kuraray [CSE]; one-step self-etch - Single Bond Universal, 3M ESPE [SBU]; and two-step etch-and-rinse - Adper Single Bond 2, 3M ESPE [SB2]), electric current direction (without electric current - control, direct and reverse electric currents - 35µA), and storage time (24h - immediate and 6 months). Resin composite blocks (Filtek Z350XT, 3M ESPE) were bonded to dentin.

Evaluation of mineral content of tooth enamel after application violet led associated with 35% hydrogen peroxide.

Background: The aim of this study was to evaluate the microhardness and quantify the presence of minerals (Calcium and Phosphorous) of tooth enamel submitted to bleaching with violet LED light, either associated with 35% hydrogen peroxide gel, or not.

Methods: Bovine incisors were selected and divided into 4 Groups according to the bleaching technique used: C- Without bleaching (Control); VL- violet LED; HP- 35% Hydrogen Peroxide; HP+VL- 35% Hydrogen Peroxide + violet LED. The response variables were surface microhardness (n = 12), Energy Dispersive Spectroscopy (EDS) (n = 6) and scanning electron microscopy (SEM) (n = 3).

Experimental resin-based dual-cured calcium aluminate and calcium titanate materials for vital pulp therapy.

This paper evaluates the physicochemical and biological properties of experimental resin-based dual-cured calcium aluminate (CA) and calcium titanate (CTi) materials for vital pulp therapy (VPT). The experimental dual-cured materials were obtained as two pastes: a) Bis-EMA 10, PEG 400, DHEPT, EDAB, camphorquinone, and butylated hydroxytoluene; and b) fluoride ytterbium, Bis-EMA 10, Bis-EMA 30, benzoyl peroxide, and butylated hydroxytoluene. The materials were divided into six groups based on the added calcium component: MTA (MTA®, Angelus); CLQ (Clinker-Fillapex®, Angelus); CA (calcined at ,1200°C in pastes a and b); CA800 (calcined at 800°C in paste a); CA1200 (calcined at 1,200°C in paste a); and CTi (paste a).

Stress distribution in restorations with glass fiber and polyetheretherketone intraradicular posts: An in silico analysis.

This study evaluated stresses generated at maxillary central incisor (21) root restored with lithium disilicate crown (LDC), and glass fiber (GFP) or polyetheretherketone (PEEK) post. 3D models created by computed tomographic image (i-CAT Cone Beam 3D Dental Imaging System) reproduced maxillary central incisor. Each model had prosthetic LDCs (2.

Bond strength of self-adhesive resin cement to dentin using different adhesion protocols.

Background: The treatment of dentin before the use of self-adhesive cements is still a crucial point to achieve the best bond strength values. The objective of this study was to evaluate the bond strength between dentin and composite resin using different adhesion strategies with self-adhesive resin cement.

Material And Methods: Forty healthy third human molars were randomly divided into 4 groups (n = 10): CA (control); application of self-adhesive cement (Rely X U200, 3M ESPE), AD + CA: only application of conventional adhesive (Adper Single Bond 2, 3M ESPE) + self-adhesive cement, AC + AD + CA; conditioning with 37% phosphoric acid for 15 seconds + application of conventional adhesive + self-adhesive cement and AC + CA; conditioning with 37% phosphoric acid for 15s + self-adhesive cement.

Propolis in Oral Healthcare: Antibacterial Activity of a Composite Resin Enriched With Brazilian Red Propolis.

The aim of this study was to obtain a Brazilian red propolis (BRP) enriched composite resin and to perform the characterization of its antibacterial activity, mechanical, and physical-chemical properties. Brazilian red propolis ethyl acetate extract (EABRP) was characterized by LC-ESI-Orbitrap-FTMS, UPLC-DAD, antibacterial activity, total flavonoids content, and radical scavenging capacity. BRP was incorporated to a commercial composite resin (RC) to obtain BRP enriched composite at 0.

Adhesive systems applied to dentin substrate under electric current: systematic review.

Objectives: The purpose of this systematic review was to collect and discuss the technique of adhesive systems application on dentin substrate under electric current.

Materials And Methods: The first search strategy was based on data available at PubMed, LILACS, Scielo, Scopus, and Cochrane Library, using a combination of descriptors such as "dentin bond agents OR adhesive system AND electric current OR electrobond" or "dentin bonding agents OR dentin bonding agent application OR adhesive system AND electric current OR electrobond", with no limit regarding the publication year. The second search strategy was based on the articles' references found previously.

Finite Element Analysis of Stress in Anterior Prosthetic Rehabilitation with Zirconia Implants with and without Cantilever.

Objectives: The aim of this study was to evaluate using finite element analysis (FEA), the stress distribution in prostheses (lithium disilicate crowns) on monotype zirconia implants with and without cantilever in the anterior region of the maxilla.

Materials And Methods: From a virtual reconstruction of bone model of the toothed maxilla from a computed tomography, three models (groups) were created: Zr (11-21)-implants placed in the area of 11 and 21 with cantilever; Zr (12-22)-implants placed in the area of 12 and 22 without cantilever; and Zr (11-22)-implants intercalated placed in the area of 11 and 22. In all models, monotype zirconia implant (4.

Electric current effects on bond strength, nanoleakage, degree of conversion and dentinal infiltration of adhesive systems.

To evaluate the effect of three adhesive systems applied under electric current on microtensile bond strength (μTBS) and degree of conversion (DC). Molar teeth were restored with the aid of three adhesive systems (Adper Single Bond 2-SB2; Clearfil SE Bond-CSE; and Single Bond Universal-SBU) under different electric current intensities (0 μA; 25 μA; and 50 μA). Composite resin blocks were built up in increments (2 mm) and sectioned into 1 × 1 mm beams.

Polycaprolactone/Beta-Tricalcium Phosphate Scaffolds Obtained via Rotary Jet-Spinning: in vitro and in vivo Evaluation.

This study aimed to evaluate in vitro and in vivo polymeric membranes obtained by a rotary jet-spinning process for the repair of critical bone defects in the calvaria of Wistar rats, for future use in tissue engineering. Experimental sample collections were performed on the 30, 60 and 90th postoperative days, and the analyses performed were histomorphometric, immunohistochemistry, and western blotting. Reducing inflammatory infiltrate in all groups and experimental periods, angiogenesis on the 30th day did not show any difference between the groups, on the 60th day, 5% polycaprolactone/beta-tricalcium phosphate(PCL/β-TCP) was high compared to control (C), and on the 90th day, the same group reduced when compared to C and 10% PCL/β-TCP.

Resin composite adhesion to dentin using different curing lights and adhesive systems applied under electric current.

Objectives: To evaluate the effect of electric current application on the resin composite-tooth bond strength and hybrid layer of three adhesive systems light-cured by two light-curing units (LCUs).

Materials And Methods: Human molar teeth were distributed into 12 groups (n=6). Three adhesive systems were used: two-step etch-and-rinse (SB2; Adper Single Bond 2, 3M ESPE); two-step self-etch (CSE; Clearfil SE Bond, Kuraray); and one-step self-etch (SBU; Single Bond Universal, 3M ESPE) applied with (50μA) and without (control; conventional application) electric current, and light-cured with different LCUs.

Physical and Mechanical Properties of Resins Blends Containing a Monomethacrylate with Low-polymerization Shrinkage.

Objectives:  The aim of this study was to evaluate the Knoop hardness (KH), cross-link density (CLD), water sorption (WS), water solubility (WSB), and volumetric shrinkage (VS) of experimental resins blends containing a monomethacrylate with low-polymerization shrinkage.

Materials And Methods:  A blend of bisphenol glycidyl methacrylate (BisGMA) as base monomer was formulated with (Bis-GMA)/triethyleneglycol dimethacrylate (TEGDMA), Bis-GMA/isobornyl methacrylate (IBOMA), or Bis-GMA/TEGDMA/IBOMA in different concentrations (40, 50, or 60 wt%). The camphorquinone (CQ)/2-(dimethylamino) ethyl methacrylate (DMAEMA) was used as the photoinitiator system.

Biomechanical evaluation of anterior implants associated with titanium and zirconia abutments and monotype zirconia implants.

Purpose: The present in silico study evaluated the behavior of titanium dental implants associated with abutments in zirconia and monotype zirconia implant using finite element analysis (FEA).

Methods: A partial image of the anterior region of the maxilla was obtained by computed tomography. Three models of finite element were made using 3D modeling software (SolidWorks): Ti-Ti (control): implant morse cone (3.

Effect of Electric Current-assisted Application of Adhesives on their Bond Strength and Quality.

Purpose: To assess the effect of the application of different electric currents on dentin bonding and resin infiltration of self-etching and etch-and-rinse adhesives.

Materials And Methods: Two hundred four sound third molars were selected and divided in groups according to the adhesive (self-etch [CSE, Clearfil SE Bond, Kuraray Noritake], universal [SBU, Single Bond Universal, 3M Oral Care], and etch-and-rinse [SB2, Adper Single Bond 2 (SB2), 3M Oral Care]) and electrical current used (0, 5, 10, 15, 20, 25, 30, and 35 μA). Light curing was performed for 10 s with an LED-curing unit at 1000 mW/cm2.

Bonding Strength of Universal Adhesives to Indirect Substrates: A Meta-Analysis of in Vitro Studies.

Purpose: To evaluate the in vitro bond strength of universal adhesive systems to indirect substrates.

Material And Methods: Two reviewers performed a literature search up to March 2018 in seven databases: PubMed, Web of Science, SciELO, Scopus, LILACS, IBECS, and BBO. The review included studies that compared the bond strength of universal adhesives and well-established material-specific primers to indirect substrates: lithium disilicate ceramic, yttrium-stabilized zirconium dioxide ceramic, leucite-reinforced ceramic, feldspathic porcelain, polymer infiltrated ceramic material, resin composite or metal alloys.

Effect of Implant Platform Connection and Abutment Material on Removal Torque and Implant Hexagon Plastic Deformation.

Objectives:  The aim of this study was to evaluate the plastic deformation of the hexagonal connection, and the removal torque of the implant-abutment joint of two dental implants combined with internal or external hexagonal connection implants after mechanical cycling.

Materials And Methods:  Twenty-four dental implants were used in the study. Half of the implants had internal hexagonal connections (IH; Titamax II Plus) and the other half had external hexagonal connections (EH; Titamax Ti Ex).

Mechanical properties of experimental resin cements containing different photoinitiators and co-initiators.

Aim: The aim of this study was to evaluate the influence of different concentrations of two photoinitiators and one co-initiator on the flexural strength (FS) and elastic modulus (E) of experimental resin cements.

Materials And Methods: A mixture containing BisGMA, TEGDMA, and barium-aluminum-silicate (BaAlSi) and silanized colloidal silica (SiO) filler particles was prepared with two photoinitiators, viz. camphorquinone (CQ) and bisacylphosphine oxide (BAPO).

Effect of Glass Fiber Post Adaptation on Push-Out Bond Strength to Root Dentin.

The aim of this study was to evaluate the effect of different glass fiber posts (GFPs) diameters on the push-out bond strength to dentin. Forty unirradicular human teeth were endodontically treated and used for cementation of GFPs (White Post DC, FGM) with different diameters (n=10): P1 - ø 1.6 mm coronal x 0.

Addition of phosphates and chlorhexidine to resin-modified MTA materials.

To evaluate the properties of experimental mineral trioxide aggregate (MTA) resin-modified materials for root-end filling procedures, varying their compositions regarding the addition of hydroxiapatite (HA) or dicalcium phosphate dihydrate, with or without chlorhexidine digluconate. White MTA (Angelus, Londrina, Brazil) was used as a reference material. Degree of conversion (DC) was evaluated by Fourier transformed infrared (FTIr) spectroscopy (n = 5).

Effect of Thermocycling, Teeth, and Polymerization Methods on Bond Strength Teeth-Denture Base.

Objective: To evaluate the shear bond strength between different artificial teeth and denture base polymerized by two polymerization methods submitted to thermocycling.

Materials And Methods: Two acrylic resins were selected according to the polymerization method (water-bath and microwave), and four different artificial teeth (Biotone, Dentsply; Trilux, Vipi Dent; Premium 8, Heraeus Kulzer; Soluut PX, Yamahachi) were also tested. The polymerization of the acrylic resin was performed by using conventional cycle (8 h at 74°C) in water-bath and using two cycles (20 min at 270 W + 5 min at 360 W) by the microwave method.

Bond Strength of Experimental Root Canal Sealers Based on MTA and Butyl Ethylene Glycol Disalicylate.

This study investigated the bond strength of two experimental root canal sealers based on MTA and butyl ethylene glycol disalicylate: MTAe and MTAe-HA. The reference materials used for comparison were AH Plus and MTA Fillapex. Twenty human upper incisors were selected and one 1 mm slice was obtained from the cervical third of each root.

Effect of polymerization method and fabrication method on occlusal vertical dimension and occlusal contacts of complete-arch prosthesis.

Purpose: This study evaluated the dimensional stability of a complete-arch prosthesis processed by conventional method in water bath or microwave energy and polymerized by two different curing cycles.

Materials And Methods: Forty maxillary complete-arch prostheses were randomly divided into four groups (n = 10): MW1 - acrylic resin cured by one microwave cycle; MW2 - acrylic resin cured by two microwave cycles: WB1 - conventional acrylic resin polymerized using one curing cycle in a water bath; WB2 - conventional acrylic resin polymerized using two curing cycles in a water bath. For evaluation of dimensional stability, occlusal vertical dimension (OVD) and area of contact points were measured in two different measurement times: before and after the polymerization method.

Influence of plasma-based dry etching on the bond strength of Y-TZP ceramic.

The aim of this study was to evaluate the bond strength between an yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic and a luting agent when submitted to plasma etching surface treatment before and after thermocycling (TC) with 3000 cycles of 5°C-55°C. The null hypothesis was that the surface treatments and thermocycling would not influence the bond strength. A total of 160 Y-TZP ceramic blocks in 2 sizes (10 size 1 and 10 size 2 blocks in each group) were distributed into 8 groups: group C (control), no surface treatment; group C-TC, TC without prior surface treatment; group SAO, sandblasting with aluminum oxide (Al2O3); group SAO-TC, sandblasting with Al2O3 followed by TC; group SAOS, sandblasting with silica-coated Al2O3; group SAOS-TC, sandblasting with silica-coated Al2O3 followed by TC; group PE, plasma etching; and group PE-TC, plasma etching followed by TC.