Elastic Modulus Measurement at High Temperatures for Miniature Ceramic Samples Using Laser Micro-Machining and Thermal Mechanical Analyzer.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale at high temperatures. We used a picosecond laser to precisely cut microbeams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm and a length of ~1 cm.

Electrochemical Performance of Polymer-Derived Silicon-Oxycarbide/Graphene Nanoplatelet Composites for High-Performance Li-Ion Batteries.

Amorphous polymer-derived silicon-oxycarbide (SiOC) ceramics have a high theoretical capacity and good structural stability, making them suitable anode materials for lithium-ion batteries. However, SiOC has low electronic conductivity, poor transport properties, low initial Couloumbic efficiency, and limited rate capability. Therefore, there is an urgent need to explore an efficient SiOC-based anode material that could mitigate the abovementioned limitations.

Mesoscale Modeling of Phase Separation Controlled by Hydrosilylation in Polyhydromethylsiloxane (PHMS)-Containing Blends.

Controlling morphology of polysiloxane blends crosslinked by the hydrosilylation reaction followed by pyrolysis constitutes a robust strategy to fabricate polymer-derived ceramics (PDCs) for a number of applications, from water purification to hydrogen storage. Herein, we introduce a dissipative particle dynamics (DPD) approach that captures the phase separation in binary and ternary polymer blends undergoing hydrosilylation. Linear polyhydromethylsiloxane (PHMS) chains are chosen as preceramic precursors and linear vinyl-terminated polydimethylsiloxane (-PDMS) chains constitute the reactive sacrificial component.

The effect of laser sintering on the microstructure, relative density, and cracking of sol-gel-derived silica thin films.

Combining sol-gel processing and laser sintering is a promising way for fabricating functional ceramic deposition with high dimensional resolution. In this work, crack-free silica tracks on a silica substrate with a thickness from ~360 nm to ~950 nm, have been obtained by direct exposure to a CO laser beam. At a fixed scanning speed, the density and microstructures of the silica deposition can be precisely controlled by varying the laser output power.

FEM Modeling of In-Plane Stress Distribution in Thick Brittle Coatings/Films on Ductile Substrates Subjected to Tensile Stress to Determine Interfacial Strength.

The ceramic-metal interface is present in various material structures and devices that are vulnerable to failures, like cracking, which are typically due to their incompatible properties, e.g., thermal expansion mismatch.

Planar, Polysilazane-Derived Porous Ceramic Supports for Membrane and Catalysis Applications.

Porous, silicon carbonitride-based ceramic support structures for potential membrane and catalysis applications were generated from a preceramic polysilazane precursor in combination with spherical, ultrahigh-molecular weight polyethylene microparticles through a sacrificial filler approach. A screening evaluation was used for the determination of the impact of both porogen content and porogen size on pore structure, strength, and permeability characteristics of planar specimens. By optimizing both the composition as well as cross-linking parameters, maximum characteristic biaxial flexural strengths of 65 MPa and porosities of 42% were achieved.

A novel processing approach for free-standing porous non-oxide ceramic supports from polycarbosilane and polysilazane precursors.

In this contribution, a low-pressure/low-temperature casting technique for the preparation of novel free-standing macrocellular polymer-derived ceramic support structures is presented. Preceramic polymers (polycarbosilane and poly(vinyl)silazane) are combined with sacrificial porogens (ultra-high molecular weight polyethylene microbeads) to yield porous ceramic materials in the Si-C or Si-C-N systems, exhibiting well-defined pore structures after thermal conversion. The planar-disc-type specimens were found to exhibit biaxial flexural strengths of up to 60 MPa.

Maintenance of a bone collagen phenotype by osteoblast-like cells in 3D periodic porous titanium (Ti-6Al-4 V) structures fabricated by selective electron beam melting.

Regular 3D periodic porous Ti-6Al-4 V structures were fabricated by the selective electron beam melting method (EBM) over a range of relative densities (0.17-0.40) and pore sizes (500-1500 µm).

Control of surface energy of silicon oxynitride films.

Microstructure and chemical composition determine the wetting property of solid surfaces. To achieve hydrophobicity or hydrophilicity, recent efforts have mostly focused on designed patterns and sophisticated surface modification. Here we show the fabrication of a dense amorphous silicon oxynitride (SiON) film by simple annealing of perhydropolysilazane (PHPS), which experiences significant and abrupt transition in surface energy as a function of temperature.

Compression-compression fatigue of selective electron beam melted cellular titanium (Ti-6Al-4V).

Regular 3D periodic porous Ti-6Al-4V structures intended to reduce the effects of stress shielding in load-bearing bone replacement implants (e.g., hip stems) were fabricated over a range of relative densities (0.

Influence of adhesion and friction on the geometry of packings of spherical particles.

We study the effect of both adhesion and friction on the geometry of monosized packings of spheres by means of discrete element simulations. We use elastic properties that are characteristic of materials typically used for particulate processing (Young's modulus in the range 20-200 GPa). The geometrical features, both global and local, of the packings are studied using a variety of approaches in order to investigate their ability to quantify the effect of adhesion and/or friction.