Laser-Induced Graphene Electrodes for Flexible pH Sensors.

In the growing field of personalized medicine, non-invasive wearable devices and sensors are valuable diagnostic tools for the real-time monitoring of physiological and biokinetic signals. Among all the possible multiple (bio)-entities, pH is important in defining health-related biological information, since its variations or alterations can be considered the cause or the effect of disease and disfunction within a biological system. In this work, an innovative (bio)-electrochemical flexible pH sensor was proposed by realizing three electrodes (working, reference, and counter) directly on a polyimide (Kapton) sheet through the implementation of CO laser writing, which locally converts the polymeric sheet into a laser-induced graphene material (LIG electrodes), preserving inherent mechanical flexibility of Kapton.

Microbial Fuel Cells as Effective Tools for Energy Recovery and Antibiotic Detection in Water and Food.

This work demonstrates that microbial fuel cells (MFCs), optimized for energy recovery, can be used as an effective tool to detect antibiotics in water-based environments. In MFCs, electroactive biofilms function as biocatalysts by converting the chemical energy of organic matter, which serves as the fuel, into electrical energy. The efficiency of the conversion process can be significantly affected by the presence of contaminants that act as toxicants to the biofilm.

Ultrasonic Spray Coating to Optimize Performance of Bio-Electrochemical Systems.

This work investigates the optimization of carbon-based electrodes employed in bio-electrochemical systems (BES) through the deposition of nanostructured layers of poly(3,4-ethylene-dioxy-thiophene) poly(styrene-sulfonate) (PEDOT:PSS) on commercial carbon paper electrodes via ultrasonic spray coating (USC). This innovative application of USC demonstrated that uniform and controlled depositions of PEDOT:PSS can be successfully performed on carbon-based electrodes. To this end, the morphology and spatial uniformity of depositions were verified via scanning electron microscopy and Raman spectroscopy.

A Nanofiber-Based Gas Diffusion Layer for Improved Performance in Air Cathode Microbial Fuel Cells.

This work investigates a new nanostructured gas diffusion layer (nano-GDL) to improve the performance of air cathode single-chamber microbial fuel cells (a-SCMFCs). The new nano-GDLs improve the direct oxygen reduction reaction by exploiting the best qualities of nanofibers from electrospinning in terms of high surface-area-to-volume ratio, high porosity, and laser-based processing to promote adhesion. By electrospinning, nano-GDLs were fabricated directly by collecting two nanofiber mats on the same carbon-based electrode, acting as the substrate.

Design, Fabrication, and Experimental Validation of Microfluidic Devices for the Investigation of Pore-Scale Phenomena in Underground Gas Storage Systems.

The understanding of multiphase flow phenomena occurring in porous media at the pore scale is fundamental in a significant number of fields, from life science to geo and environmental engineering. However, because of the optical opacity and the geometrical complexity of natural porous media, detailed visual characterization is not possible or is limited and requires powerful and expensive imaging techniques. As a consequence, the understanding of micro-scale behavior is based on the interpretation of macro-scale parameters and indirect measurements.

3D Composite PDMS/MWCNTs Aerogel as High-Performing Anodes in Microbial Fuel Cells.

Porous 3D composite materials are interesting anode electrodes for single chamber microbial fuel cells (SCMFCs) since they exploit a surface layer that is able to achieve the correct biocompatibility for the proliferation of electroactive bacteria and have an inner charge transfer element that favors electron transfer and improves the electrochemical activity of microorganisms. The crucial step is to fine-tune the continuous porosity inside the anode electrode, thus enhancing the bacterial growth, adhesion, and proliferation, and the substrate's transport and waste products removal, avoiding pore clogging. To this purpose, a novel approach to synthetize a 3D composite aerogel is proposed in the present work.

Living Bacteria Directly Embedded into Electrospun Nanofibers: Design of New Anode for Bio-Electrochemical Systems.

The aim of this work is the optimization of electrospun polymeric nanofibers as an ideal reservoir of mixed electroactive consortia suitable to be used as anodes in Single Chamber Microbial Fuel Cells (SCMFCs). To reach this goal the microorganisms are directly embedded into properly designed nanofibers during the electrospinning process, obtaining so called nanofiber-based bio-composite (bio-NFs). This research approach allowed for the designing of an advanced nanostructured scaffold, able to block and store the living microorganisms inside the nanofibers and release them only after exposure to water-based solutions and electrolytes.

Electrospun PEO/PEDOT:PSS Nanofibers for Wearable Physiological Flex Sensors.

Flexible sensors are fundamental devices for human body monitoring. The mechanical strain and physiological parameters coupled sensing have attracted increasing interest in this field. However, integration of different sensors in one platform usually involves complex fabrication process-flows.

Design and Optimization of Piezoresistive PEO/PEDOT:PSS Electrospun Nanofibers for Wearable Flex Sensors.

Flexible strain sensors are fundamental devices for application in human body monitoring in areas ranging from health care to soft robotics. Stretchable piezoelectric strain sensors received an ever-increasing interest to design novel, robust and low-cost sensing units for these sensors, with intrinsically conductive polymers (ICPs) as leading materials. We investigated a sensitive element based on crosslinked electrospun nanofibers (NFs) directly collected and thermal treated on a flexible and biocompatible substrate of polydimethylsiloxane (PDMS).

Electrospun Nanofibers: from Food to Energy by Engineered Electrodes in Microbial Fuel Cells.

Microbial fuel cells (MFCs) are bio-electrochemical devices able to directly transduce chemical energy, entrapped in an organic mass named fuel, into electrical energy through the metabolic activity of specific bacteria. During the last years, the employment of bio-electrochemical devices to study the wastewater derived from the food industry has attracted great interest from the scientific community. In the present work, we demonstrate the capability of exoelectrogenic bacteria used in MFCs to catalyze the oxidation reaction of honey, employed as a fuel.

Photofabrication of polymeric biomicrofluidics: New insights into material selection.

We propose a versatile method to evaluate the suitability of polymers for the fabrication of microfluidic devices for biomedical applications, based on the concept that the selection and the design of convenient materials should involve different properties depending on the final microfluidic application. Here polymerase chain reaction (PCR) is selected as biological model and target microfluidic reaction. A class of photocured siloxanes is introduced as device building polymers and copolymerization is adopted as strategy to finely tune and optimize the final material properties.

Environmental electroactive consortia as reusable biosensing element for freshwater toxicity monitoring.

The development of tools to monitor water quality is mandatory in a scenario where clean water resources are decreasing. Here, the biosensing capability of an electroactive river sediment consortium was tested towards three model contaminants (glutaraldehyde, nickel(II) and chromium(III)). The proposed biosensor is a small membrane-less single chamber Microbial Fuel Cell (MFC), fabricated by 3D printing.

Tuning Porosity and Functionality of Electrospun Rubber Nanofiber Mats by Photo-Crosslinking.

The present work proposes a versatile and efficient method to fabricate rubber nanofiber membranes with a controlled morphology and tailored functionality, based on the application of photoinduced thiol-ene cross-linking reactions to electrospun mats. Besides preventing the polymer cold flow and freezing the structure obtained by electrospinning, the photocuring step finely controls the morphology of the nanofiber mats, in terms of the fiber diameter up to the nanometer range and of the membrane porosity. Nanofiber membranes are also made chemically resistant, while retaining their flexibility.

Anodic microbial community analysis of microbial fuel cells based on enriched inoculum from freshwater sediment.

The characterization of anodic microbial communities is of great importance in the study of microbial fuel cells (MFCs). These kinds of devices mainly require a high abundance of anode respiring bacteria (ARB) in the anode chamber for optimal performance. This study evaluated the effect of different enrichments of environmental freshwater sediment samples used as inocula on microbial community structures in MFCs.

Biohybrid Cathode in Single Chamber Microbial Fuel Cell.

The aim of this work is to investigate the properties of biofilms, spontaneously grown on cathode electrodes of single-chamber microbial fuel cells, when used as catalysts for oxygen reduction reaction (ORR). To this purpose, a comparison between two sets of different carbon-based cathode electrodes is carried out. The first one (Pt-based biocathode) is based on the proliferation of the biofilm onto a Pt/C layer, leading thus to the creation of a biohybrid catalyst.

Thermal evolution of MnO nanofibres as catalysts for the oxygen reduction reaction.

Manganese oxides (MnO) are considered as a promising catalyst alternative to platinum in fuel cell applications. In fact, a proper catalyst is needed in order to facilitate the oxygen reduction reaction (ORR) at the cathode, and platinum is considered the best material due to its low overpotential for this reaction. Contrary to platinum, MnO is inexpensive, environmentally friendly and can be shaped into several nanostructures; furthermore, most of them show significant electro-catalytic performance.

New insights in Microbial Fuel Cells: novel solid phase anolyte.

For the development of long lasting portable microbial fuel cells (MFCs) new strategies are necessary to overcome critical issues such as hydraulic pump system and the biochemical substrate retrieval overtime to sustain bacteria metabolism. The present work proposes the use of a synthetic solid anolyte (SSA), constituted by agar, carbonaceous and nitrogen sources dissolved into diluted seawater. Results of a month-test showed the potential of the new SSA-MFC as a long lasting low energy consuming system.

Nanostructural evolution of one-dimensional BaTiO₃ structures by hydrothermal conversion of vertically aligned TiO₂ nanotubes.

The use of TiO2 nanotube (NT) arrays as templates for hydrothermal conversion of one-dimensional barium titanate (BaTiO3) structures is considered a promising synthesis approach, even though the formation mechanisms are not yet fully understood. Herein we report a nanostructural study by means of XRD and (HR)TEM of high aspect ratio TiO2-NTs hydrothermally converted into BaTiO3. The nanostructure shows two different and well-defined regions: at the top the conversion involves complete dissolution of NTs and subsequent precipitation of BaTiO3 crystals by homogeneous nucleation, followed by the growth of dendritic structures by aggregation and oriented attachment mechanisms.

Microwave-Assisted Synthesis of Reduced Graphene Oxide/SnO2 Nanocomposite for Oxygen Reduction Reaction in Microbial Fuel Cells.

We report on an easy, fast, eco-friendly, and reliable method for the synthesis of reduced graphene oxide/SnO2 nanocomposite as cathode material for application in microbial fuel cells (MFCs). The material was prepared starting from graphene oxide that has been reduced to graphene during the hydrothermal synthesis of the nanocomposite, carried out in a microwave system. Structural and morphological characterizations evidenced the formation of nanocomposite sheets, with SnO2 crystals of few nanometers integrated in the graphene matrix.

Oxygen-Inhibition Lithography for the Fabrication of Multipolymeric Structures.

The oxygen inhibition of UV curable polymers is exploited in novel technology for the fabrication of patterns and closed devices. Multiscale structures with thicknesses ranging from few micro-meters to millimeters are rapidly fabricated. Multipolymeric and multifunctional structures are also prepared: adequately choosing the material of each layer, a set of different properties is arranged in the same device.

Dispelling clichés at the nanoscale: the true effect of polymer electrolytes on the performance of dye-sensitized solar cells.

In the field of dye-sensitized solar cells, polymer electrolytes are among the most studied materials due to their ability to ensure both high efficiency and stability, the latter being a critical point of these devices. Hundreds of polymeric matrices have been proposed over the years, and their functionalization with several groups, the variation of their molecular weight and the tuning of the crosslinking degree have been investigated. However, the true effect that polymeric matrices have on the cell parameters has often been addressed superficially, and hundreds of papers justify the obtained results with a simple bibliographic reference to other systems (sometimes completely different).

Ultrafast room-temperature crystallization of TiO2 nanotubes exploiting water-vapor treatment.

In this manuscript a near-room temperature crystallization process of anodic nanotubes from amorphous TiO2 to anatase phase with a fast 30 minutes treatment is reported for the first time. This method involves the exposure of as-grown TiO2 nanotubes to water vapor flow in ambient atmosphere. The water vapor-crystallized samples are deeply investigated in order to gain a whole understanding of their structural, physical and chemical properties.

OncomiR detection in circulating body fluids: a PDMS microdevice perspective.

There is an increasing interest in circulating microRNAs (miRNAs) as potential minimally invasive diagnostic biomarkers in oncology. Considerable efforts are being made in the development of lab-on-a-chip devices for biomedical applications to purify and detect miRNAs from biological fluids. Here, we report the development of an innovative polydimethylsiloxane (PDMS)-based parallel device whose internal surface can opportunely be functionalized with positively charged 3-aminopropyltriethoxysilane (APTES) alone or mixed with two different neutral poly(ethylene glycol) silanes (PEG-s).

Direct photolithography of perfluoropolyethers for solvent-resistant microfluidics.

In this work, photocurable perfluoropolyethers (PFPEs) have been used for the fabrication of microfluidic devices by a direct photolithographic process. During this mask-assisted photopolymerization technique, the material is directly photopolymerized in the presence of a mask, avoiding the use of a master. We demonstrate the high level of control in transferring micropattern features with high density, a minimum transferred size of 15 μm, a high aspect ratio (at least up to 6.

Charge transport improvement employing TiO2 nanotube arrays as front-side illuminated dye-sensitized solar cell photoanodes.

TiO(2) nanotube (NT) arrays with different lengths were fabricated by anodic oxidation of Ti foil and free-standing NT membranes were detached by the metal substrate and bonded on the fluorine-doped tin oxide surface implementing an easy procedure. Morphology of the as-grown material and of the prepared photoanode was investigated by means of electron microscopy, deepening the investigation on the thermal treatment effect. Crystalline orientation and exposed surface area were studied by X-ray diffraction and Brunauer-Emmett-Teller measurements, showing suitable characteristics for the application in dye-sensitized solar cells (DSCs).