Enhanced efficiency of bifacial perovskite solar cells using computational study.

The most rapidly expanding type of solar cells are the Perovskite Solar Cells (PSCs), because of its high device performance, ease of synthesis, high open-circuit voltage, and affordability. Despite these advantages, the development of perovskite-based solar cells continues to be impeded by the issues with perovskite stability and the utilization of the hazardous heavy element lead (Pb). The study emphasizes on the bifacial structure that maintains the conventional absorber layer and electron transport layer (ETL) in the optimized PSC structure.

Fabrication of Bi2Te3 and Sb2Te3 Thermoelectric Thin Films using Radio Frequency Magnetron Sputtering Technique.

Through various studies on thermoelectric (TE) materials, thin film configuration gives superior advantages over conventional bulk TEs, including adaptability to curved and flexible substrates. Several different thin film deposition methods have been explored, yet magnetron sputtering is still favorable due to its high deposition efficiency and scalability. Therefore, this study aims to fabricate a bismuth telluride (Bi2Te3) and antimony telluride (Sb2Te3) thin film via the radio frequency (RF) magnetron sputtering method.

An experimental investigation of spin-on doping optimization for enhanced electrical characteristics in silicon homojunction solar cells: Proof of concept.

The pursuit of enhancing the performance of silicon-based solar cells is pivotal for the progression of solar photovoltaics as the most potential renewable energy technologies. Despite the existence of sophisticated methods like diffusion and ion implantation for doping phosphorus into p-type silicon wafers in the semiconductor industry, there is a compelling need to research spin-on doping techniques, especially in the context of tandem devices, where fabricating the bottom cell demands meticulous control over conditions. The primary challenge with existing silicon cell fabrication methods lies in their complexity, cost, and environmental concerns.

Systematic inspection on the interplay between MoNa-induced sodium and the formation of MoSe intermediate layer in CIGSe/Mo heterostructures.

The critical impact of sodium-doped molybdenum (MoNa) in shaping the MoSe interfacial layer, influencing the electrical properties of CIGSe/Mo heterostructures, and achieving optimal MoSe formation conditions, leading to improved hetero-contact quality. Notably, samples with a 600-nm-thick MoNa layer demonstrate the highest resistivity (73 μΩcm) and sheet resistance (0.45 Ω/square), highlighting the substantial impact of MoNa layer thickness on electrical conductivity.

Dopant engineering for ZnO electron transport layer towards efficient perovskite solar cells.

The conventional electron transport layer (ETL) TiO has been widely used in perovskite solar cells (PSCs), which have produced exceptional power conversion efficiencies (PCE), allowing the technology to be highly regarded and propitious. Nevertheless, the recent high demand for energy harvesters in wearable electronics, aerospace, and building integration has led to the need for flexible solar cells. However, the conventional TiO ETL layer is less preferred, where a crystallization process at a temperature as high as 450 °C is required, which degrades the plastic substrate.

Elucidating the Effects of Interconnecting Layer Thickness and Bandgap Variations on the Performance of Monolithic Perovskite/Silicon Tandem Solar Cell by wxAMPS.

In this study, we investigated the pathways for integration of perovskite and silicon solar cells through variation of the properties of the interconnecting layer (ICL). The user-friendly computer simulation software wxAMPS was used to conduct the investigation. The simulation started with numerical inspection of the individual single junction sub-cell, and this was followed by performing an electrical and optical evaluation of monolithic 2T tandem PSC/Si, with variation of the thickness and bandgap of the interconnecting layer.

Metal organic framework derived NiO nanoparticles for application as a hole transport layer in perovskite solar cells.

NiO as a hole transport layer (HTL) has gained a lot of research interest in perovskite solar cells (PSCs), owing to its high optical transmittance, high power conversion efficiency, wide band-gap and ease of fabrication. In this work, four different nickel based-metal organic frameworks (MOFs) using 1,3,5-benzenetricarboxylic acid (BTC), terephthalic acid (TPA), 2-aminoterephthalic acid (ATPA), and 2,5-dihydroxyterephthalic acid (DHTPA) ligands respectively, have been employed as precursors to synthesize NiO NPs. The employment of different ligands was found to result in NiO NPs with different structural, optical and morphological properties.

Probing the Interplay between Mo Back Contact Layer Deposition Condition and MoSe Layer Formation at the CIGSe/Mo Hetero-Interface.

The effect of Mo thin film deposition power in DC sputtering on the formation of a MoSe interfacial layer grown via the annealing of CIGSe/Mo precursors in an Se-free atmosphere was investigated. A Mo layer was deposited on glass substrates using the DC magnetron sputtering method. Its electrical resistivity, as well as its morphological, structural, and adhesion characteristics, were analyzed regarding the deposition power.

Raytracing Modelling of Infrared Light Management Using Molybdenum Disulfide (MoS) as a Back-Reflector Layer in a Silicon Heterojunction Solar Cell (SHJ).

The silicon heterojunction solar cell (SHJ) is considered the dominant state-of-the-art silicon solar cell technology due to its excellent passivation quality and high efficiency. However, SHJ's light management performance is limited by its narrow optical absorption in long-wave near-infrared (NIR) due to the front, and back tin-doped indium oxide (ITO) layer's free carrier absorption and reflection losses. Despite the light-trapping efficiency (LTE) schemes adopted by SHJ in terms of back surface texturing, the previous investigations highlighted the ITO layer as a reason for an essential long-wavelength light loss mechanism in SHJ solar cells.

A Comparative Study on p- and n-Type Silicon Heterojunction Solar Cells by AFORS-HET.

Despite the increasing trend of n-type silicon wafer utilization in the manufacturing of high-efficiency heterojunction solar cells due to the superior advantages over p-type counterparts, its high manufacturing cost remains to be one of the most crucial factors, which impedes its market share growth with state-of-the-art silicon heterojunction (SHJ) solar cells demonstrating high conversion efficiencies from various configurations, the prospect of using an n-type wafer is debatable from a cost-efficiency point of view. Hence, a systematic comparison between p- and n-type SHJ solar cells was executed in this work using AFORS-HET numerical software. Front and rear-emitter architectures were selected for each type of wafer with ideal (without defects) and non-ideal (with defects) conditions.

High Quality CdS Thin Film Growth by Avoiding Anomalies in Chemical Bath Deposition for Large Area Thin Film Solar Cell Application.

Many high efficiency thin-film solar cells incorporate a thin layer of CdS in the device structure to form a heterojunction. Chemical bath deposition (CBD) is the most preferred method of deposition especially for large area thin film solar cells. This study explored the effects of ammonium sulfate on the CdS film produced by CBD using cadmium sulfate as the cadmium source.