Revealing the Structural Organization of Gamma-irradiated Starch Granules Using Polarization-resolved Second Harmonic Generation Microscopy.

Starch is a semi-crystalline macromolecule with the presence of amorphous and crystalline components. The amorphous amylose and crystalline amylopectin regions in starch granules are susceptible to certain physical modifications, such as gamma irradiation. Polarization-resolved second harmonic generation (P-SHG) microscopy in conjunction with SHG-circular dichroism (CD) was used to assess the three-dimensional molecular order and inherent chirality of starch granules and their reaction to different dosages of gamma irradiation.

Isolation, Detection and Analysis of Circulating Tumour Cells: A Nanotechnological Bioscope.

Cancer is one of the dreaded diseases to which a sizeable proportion of the population succumbs every year. Despite the tremendous growth of the health sector, spanning diagnostics to treatment, early diagnosis is still in its infancy. In this regard, circulating tumour cells (CTCs) have of late grabbed the attention of researchers in the detection of metastasis and there has been a huge surge in the surrounding research activities.

The revolution of PDMS microfluidics in cellular biology.

Microfluidics is revolutionizing the way research on cellular biology has been traditionally conducted. The ability to control the cell physicochemical environment by adjusting flow conditions, while performing cellular analysis at single-cell resolution and high-throughput, has made microfluidics the ideal choice to replace traditional models. However, such a revolution only truly started with the advent of polydimethylsiloxane (PDMS) as a microfluidic structural material and soft-lithography as a rapid manufacturing technology.

Low-frequency meandering piezoelectric vibration energy harvester.

The design, fabrication, and characterization of a novel low-frequency meandering piezoelectric vibration energy harvester is presented. The energy harvester is designed for sensor node applications where the node targets a width-to-length aspect ratio close to 1:1 while simultaneously achieving a low resonant frequency. The measured power output and normalized power density are 118 μW and 5.

Control of current saturation and threshold voltage shift in indium oxide nanowire transistors with femtosecond laser annealing.

Transistors based on various types of nonsilicon nanowires have shown great potential for a variety of applications, especially for those that require transparency and low-temperature substrates. However, critical requirements for circuit functionality, such as saturated source-drain current and matched threshold voltages of individual nanowire transistors in a way that is compatible with low temperature substrates, have not been achieved. Here we show that femtosecond laser pulses can anneal individual transistors based on In(2)O(3) nanowires, improve the saturation of the source-drain current, and permanently shift the threshold voltage to the positive direction.

Optimization of modified volume Fresnel zone plates.

Modified volume Fresnel zone plates (MVFZPs) fabricated with laser direct writing were optimized for higher diffraction efficiencies. The Fresnel radii in each layer of a volume zone plate were iteratively adjusted by a simulation-based direct search optimization. The results show that optimization is effective but depends strongly on the starting diffraction efficiencies determined by the MVFZP parameters.

Beam propagation modeling of modified volume Fresnel zone plates fabricated by femtosecond laser direct writing.

Light diffraction by volume Fresnel zone plates (VFZPs) is simulated by the Hankel transform beam propagation method (Hankel BPM). The method utilizes circularly symmetric geometry and small step propagation to calculate the diffracted wave fields by VFZP layers. It is shown that fast and accurate diffraction results can be obtained with the Hankel BPM.

Measurement of metal/carbon nanotube contact resistance by adjusting contact length using laser ablation.

A technique of measuring contact resistance between an individual nanotube and a deposited metallic film is described. Using laser ablation to sequentially shorten the contact length between a nanotube and the evaporated metallic film, the linear resistivity of the nanotube as well as the specific contact resistivity between the nanotube and metallic film can be determined. This technique can be generally used to measure the specific contact resistance that develops between a metallic film and a variety of different nanowires and nanotubes.